static void
ar9285WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
freqIndex = 2;
if (IEEE80211_IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IEEE80211_IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
modesIndex, regWrites);
if (AR_SREV_KITE_12_OR_LATER(ah)) {
regWrites = ath_hal_ini_write(ah, &AH9285(ah)->ah_ini_txgain,
modesIndex, regWrites);
}
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
1, regWrites);
}
static void
ar9280WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
if (IEEE80211_IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IEEE80211_IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
} else {
freqIndex = 1;
if (IEEE80211_IS_CHAN_HT40(chan) ||
IEEE80211_IS_CHAN_TURBO(chan))
modesIndex = 2;
else
modesIndex = 1;
}
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
/* XXX Merlin ini fixups */
/* XXX Merlin 100us delay for shift registers */
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
modesIndex, regWrites);
if (AR_SREV_MERLIN_20_OR_LATER(ah)) {
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_rxgain,
modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_txgain,
modesIndex, regWrites);
}
/* XXX Merlin 100us delay for shift registers */
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
1, regWrites);
if (AR_SREV_MERLIN_20(ah) && IS_5GHZ_FAST_CLOCK_EN(ah, chan)) {
/* 5GHz channels w/ Fast Clock use different modal values */
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_xmodes,
modesIndex, regWrites);
}
}
static void
ar9287WriteRegs(struct ath_hal *ah, u_int modesIndex, u_int freqIndex,
int writes)
{
(void) ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_bb_rfgain,
freqIndex, writes);
}
static void
ar9285ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore)
{
if (AH_PRIVATE(ah)->ah_ispcie && !restore) {
ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_pcieserdes, 1, 0);
OS_DELAY(1000);
OS_REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
OS_REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT);
}
}
static void
ar9285WriteIni(struct ath_hal *ah, HAL_CHANNEL_INTERNAL *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
freqIndex = 2;
if (IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
modesIndex, regWrites);
if (AR_SREV_KITE_12_OR_LATER(ah)) {
regWrites = ath_hal_ini_write(ah, &AH9285(ah)->ah_ini_txgain,
modesIndex, regWrites);
}
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
1, regWrites);
OS_REG_SET_BIT(ah, AR_DIAG_SW, (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
if (AR_SREV_MERLIN_10_OR_LATER(ah)) {
uint32_t val;
val = OS_REG_READ(ah, AR_PCU_MISC_MODE2) &
(~AR_PCU_MISC_MODE2_HWWAR1);
OS_REG_WRITE(ah, AR_PCU_MISC_MODE2, val);
OS_REG_WRITE(ah, 0x9800 + (651 << 2), 0x11);
}
}
static void
ar9285AniSetup(struct ath_hal *ah)
{
/*
* These are the parameters from the AR5416 ANI code;
* they likely need quite a bit of adjustment for the
* AR9285.
*/
static const struct ar5212AniParams aniparams = {
.maxNoiseImmunityLevel = 4, /* levels 0..4 */
.totalSizeDesired = { -55, -55, -55, -55, -62 },
.coarseHigh = { -14, -14, -14, -14, -12 },
.coarseLow = { -64, -64, -64, -64, -70 },
.firpwr = { -78, -78, -78, -78, -80 },
.maxSpurImmunityLevel = 7,
.cycPwrThr1 = { 2, 4, 6, 8, 10, 12, 14, 16 },
.maxFirstepLevel = 2, /* levels 0..2 */
.firstep = { 0, 4, 8 },
.ofdmTrigHigh = 500,
.ofdmTrigLow = 200,
.cckTrigHigh = 200,
.cckTrigLow = 100,
.rssiThrHigh = 40,
.rssiThrLow = 7,
.period = 100,
};
/* NB: disable ANI noise immmunity for reliable RIFS rx */
AH5416(ah)->ah_ani_function &= ~(1 << HAL_ANI_NOISE_IMMUNITY_LEVEL);
ar5416AniAttach(ah, &aniparams, &aniparams, AH_TRUE);
}
static const char * ar9285_lna_conf[] = {
"LNA1-LNA2",
"LNA2",
"LNA1",
"LNA1+LNA2",
};
static void
ar9285_eeprom_print_diversity_settings(struct ath_hal *ah)
{
const HAL_EEPROM_v4k *ee = AH_PRIVATE(ah)->ah_eeprom;
const MODAL_EEP4K_HEADER *pModal = &ee->ee_base.modalHeader;
ath_hal_printf(ah, "[ath] AR9285 Main LNA config: %s\n",
ar9285_lna_conf[(pModal->antdiv_ctl2 >> 2) & 0x3]);
ath_hal_printf(ah, "[ath] AR9285 Alt LNA config: %s\n",
ar9285_lna_conf[pModal->antdiv_ctl2 & 0x3]);
ath_hal_printf(ah, "[ath] LNA diversity %s, Diversity %s\n",
((pModal->antdiv_ctl1 & 0x1) ? "enabled" : "disabled"),
((pModal->antdiv_ctl1 & 0x8) ? "enabled" : "disabled"));
}
/*
* Attach for an AR9285 part.
*/
static struct ath_hal *
ar9285Attach(uint16_t devid, HAL_SOFTC sc,
HAL_BUS_TAG st, HAL_BUS_HANDLE sh, uint16_t *eepromdata,
HAL_STATUS *status)
{
struct ath_hal_9285 *ahp9285;
struct ath_hal_5212 *ahp;
struct ath_hal *ah;
uint32_t val;
HAL_STATUS ecode;
HAL_BOOL rfStatus;
HALDEBUG(AH_NULL, HAL_DEBUG_ATTACH, "%s: sc %p st %p sh %p\n",
__func__, sc, (void*) st, (void*) sh);
/* NB: memory is returned zero'd */
ahp9285 = ath_hal_malloc(sizeof (struct ath_hal_9285));
if (ahp9285 == AH_NULL) {
HALDEBUG(AH_NULL, HAL_DEBUG_ANY,
"%s: cannot allocate memory for state block\n", __func__);
*status = HAL_ENOMEM;
return AH_NULL;
}
ahp = AH5212(ahp9285);
ah = &ahp->ah_priv.h;
ar5416InitState(AH5416(ah), devid, sc, st, sh, status);
/*
* Use the "local" EEPROM data given to us by the higher layers.
* This is a private copy out of system flash. The Linux ath9k
* commit for the initial AR9130 support mentions MMIO flash
* access is "unreliable." -adrian
*/
if (eepromdata != AH_NULL) {
AH_PRIVATE(ah)->ah_eepromRead = ath_hal_EepromDataRead;
AH_PRIVATE(ah)->ah_eepromWrite = NULL;
ah->ah_eepromdata = eepromdata;
}
/* override with 9285 specific state */
AH5416(ah)->ah_initPLL = ar9280InitPLL;
AH5416(ah)->ah_btCoexSetDiversity = ar9285BTCoexAntennaDiversity;
ah->ah_setAntennaSwitch = ar9285SetAntennaSwitch;
ah->ah_configPCIE = ar9285ConfigPCIE;
ah->ah_disablePCIE = ar9285DisablePCIE;
ah->ah_setTxPower = ar9285SetTransmitPower;
ah->ah_setBoardValues = ar9285SetBoardValues;
ah->ah_btCoexSetParameter = ar9285BTCoexSetParameter;
ah->ah_divLnaConfGet = ar9285_antdiv_comb_conf_get;
ah->ah_divLnaConfSet = ar9285_antdiv_comb_conf_set;
AH5416(ah)->ah_cal.iqCalData.calData = &ar9280_iq_cal;
AH5416(ah)->ah_cal.adcGainCalData.calData = &ar9280_adc_gain_cal;
AH5416(ah)->ah_cal.adcDcCalData.calData = &ar9280_adc_dc_cal;
AH5416(ah)->ah_cal.adcDcCalInitData.calData = &ar9280_adc_init_dc_cal;
AH5416(ah)->ah_cal.suppCals = ADC_GAIN_CAL | ADC_DC_CAL | IQ_MISMATCH_CAL;
AH5416(ah)->ah_spurMitigate = ar9280SpurMitigate;
AH5416(ah)->ah_writeIni = ar9285WriteIni;
AH5416(ah)->ah_rx_chainmask = AR9285_DEFAULT_RXCHAINMASK;
AH5416(ah)->ah_tx_chainmask = AR9285_DEFAULT_TXCHAINMASK;
ahp->ah_maxTxTrigLev = MAX_TX_FIFO_THRESHOLD >> 1;
if (!ar5416SetResetReg(ah, HAL_RESET_POWER_ON)) {
/* reset chip */
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't reset chip\n",
__func__);
ecode = HAL_EIO;
goto bad;
}
if (!ar5416SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't wakeup chip\n",
__func__);
ecode = HAL_EIO;
goto bad;
}
/* Read Revisions from Chips before taking out of reset */
val = OS_REG_READ(ah, AR_SREV);
HALDEBUG(ah, HAL_DEBUG_ATTACH,
"%s: ID 0x%x VERSION 0x%x TYPE 0x%x REVISION 0x%x\n",
__func__, MS(val, AR_XSREV_ID), MS(val, AR_XSREV_VERSION),
MS(val, AR_XSREV_TYPE), MS(val, AR_XSREV_REVISION));
/* NB: include chip type to differentiate from pre-Sowl versions */
AH_PRIVATE(ah)->ah_macVersion =
(val & AR_XSREV_VERSION) >> AR_XSREV_TYPE_S;
AH_PRIVATE(ah)->ah_macRev = MS(val, AR_XSREV_REVISION);
AH_PRIVATE(ah)->ah_ispcie = (val & AR_XSREV_TYPE_HOST_MODE) == 0;
/* setup common ini data; rf backends handle remainder */
if (AR_SREV_KITE_12_OR_LATER(ah)) {
HAL_INI_INIT(&ahp->ah_ini_modes, ar9285Modes_v2, 6);
HAL_INI_INIT(&ahp->ah_ini_common, ar9285Common_v2, 2);
HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
ar9285PciePhy_clkreq_always_on_L1_v2, 2);
} else {
HAL_INI_INIT(&ahp->ah_ini_modes, ar9285Modes, 6);
HAL_INI_INIT(&ahp->ah_ini_common, ar9285Common, 2);
HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
ar9285PciePhy_clkreq_always_on_L1, 2);
}
ar5416AttachPCIE(ah);
/* Attach methods that require MAC version/revision info */
if (AR_SREV_KITE_12_OR_LATER(ah))
AH5416(ah)->ah_cal_initcal = ar9285InitCalHardware;
if (AR_SREV_KITE_11_OR_LATER(ah))
AH5416(ah)->ah_cal_pacal = ar9002_hw_pa_cal;
ecode = ath_hal_v4kEepromAttach(ah);
if (ecode != HAL_OK)
goto bad;
if (!ar5416ChipReset(ah, AH_NULL)) { /* reset chip */
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n",
__func__);
ecode = HAL_EIO;
goto bad;
}
AH_PRIVATE(ah)->ah_phyRev = OS_REG_READ(ah, AR_PHY_CHIP_ID);
if (!ar5212ChipTest(ah)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: hardware self-test failed\n",
__func__);
ecode = HAL_ESELFTEST;
goto bad;
}
/*
* Set correct Baseband to analog shift
* setting to access analog chips.
*/
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
/* Read Radio Chip Rev Extract */
AH_PRIVATE(ah)->ah_analog5GhzRev = ar5416GetRadioRev(ah);
switch (AH_PRIVATE(ah)->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR) {
case AR_RAD2133_SREV_MAJOR: /* Sowl: 2G/3x3 */
case AR_RAD5133_SREV_MAJOR: /* Sowl: 2+5G/3x3 */
break;
default:
if (AH_PRIVATE(ah)->ah_analog5GhzRev == 0) {
AH_PRIVATE(ah)->ah_analog5GhzRev =
AR_RAD5133_SREV_MAJOR;
break;
}
#ifdef AH_DEBUG
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: 5G Radio Chip Rev 0x%02X is not supported by "
"this driver\n", __func__,
AH_PRIVATE(ah)->ah_analog5GhzRev);
ecode = HAL_ENOTSUPP;
goto bad;
#endif
}
rfStatus = ar9285RfAttach(ah, &ecode);
if (!rfStatus) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: RF setup failed, status %u\n",
__func__, ecode);
goto bad;
}
HAL_INI_INIT(&ahp9285->ah_ini_rxgain, ar9280Modes_original_rxgain_v2,
6);
if (AR_SREV_9285E_20(ah))
ath_hal_printf(ah, "[ath] AR9285E_20 detected; using XE TX gain tables\n");
/* setup txgain table */
switch (ath_hal_eepromGet(ah, AR_EEP_TXGAIN_TYPE, AH_NULL)) {
case AR5416_EEP_TXGAIN_HIGH_POWER:
if (AR_SREV_9285E_20(ah))
HAL_INI_INIT(&ahp9285->ah_ini_txgain,
ar9285Modes_XE2_0_high_power, 6);
else
HAL_INI_INIT(&ahp9285->ah_ini_txgain,
ar9285Modes_high_power_tx_gain_v2, 6);
break;
case AR5416_EEP_TXGAIN_ORIG:
if (AR_SREV_9285E_20(ah))
HAL_INI_INIT(&ahp9285->ah_ini_txgain,
ar9285Modes_XE2_0_normal_power, 6);
else
HAL_INI_INIT(&ahp9285->ah_ini_txgain,
ar9285Modes_original_tx_gain_v2, 6);
break;
default:
HALASSERT(AH_FALSE);
goto bad; /* XXX ? try to continue */
}
/*
* Got everything we need now to setup the capabilities.
*/
if (!ar9285FillCapabilityInfo(ah)) {
ecode = HAL_EEREAD;
goto bad;
}
/*
* Print out the EEPROM antenna configuration mapping.
* Some devices have a hard-coded LNA configuration profile;
* others enable diversity.
*/
ar9285_eeprom_print_diversity_settings(ah);
/* Print out whether the EEPROM settings enable AR9285 diversity */
if (ar9285_check_div_comb(ah)) {
ath_hal_printf(ah, "[ath] Enabling diversity for Kite\n");
}
/* Disable 11n for the AR2427 */
if (devid == AR2427_DEVID_PCIE)
AH_PRIVATE(ah)->ah_caps.halHTSupport = AH_FALSE;
ecode = ath_hal_eepromGet(ah, AR_EEP_MACADDR, ahp->ah_macaddr);
if (ecode != HAL_OK) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error getting mac address from EEPROM\n", __func__);
goto bad;
}
/* XXX How about the serial number ? */
/* Read Reg Domain */
AH_PRIVATE(ah)->ah_currentRD =
ath_hal_eepromGet(ah, AR_EEP_REGDMN_0, AH_NULL);
/*
* For Kite and later chipsets, the following bits are not
* programmed in EEPROM and so are set as enabled always.
*/
AH_PRIVATE(ah)->ah_currentRDext = AR9285_RDEXT_DEFAULT;
/*
* ah_miscMode is populated by ar5416FillCapabilityInfo()
* starting from griffin. Set here to make sure that
* AR_MISC_MODE_MIC_NEW_LOC_ENABLE is set before a GTK is
* placed into hardware.
*/
if (ahp->ah_miscMode != 0)
OS_REG_WRITE(ah, AR_MISC_MODE, OS_REG_READ(ah, AR_MISC_MODE) | ahp->ah_miscMode);
ar9285AniSetup(ah); /* Anti Noise Immunity */
/* Setup noise floor min/max/nominal values */
AH5416(ah)->nf_2g.max = AR_PHY_CCA_MAX_GOOD_VAL_9285_2GHZ;
AH5416(ah)->nf_2g.min = AR_PHY_CCA_MIN_GOOD_VAL_9285_2GHZ;
AH5416(ah)->nf_2g.nominal = AR_PHY_CCA_NOM_VAL_9285_2GHZ;
/* XXX no 5ghz values? */
ar5416InitNfHistBuff(AH5416(ah)->ah_cal.nfCalHist);
HALDEBUG(ah, HAL_DEBUG_ATTACH, "%s: return\n", __func__);
return ah;
bad:
if (ah != AH_NULL)
ah->ah_detach(ah);
if (status)
*status = ecode;
return AH_NULL;
}
static void
ar9285ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore, HAL_BOOL power_off)
{
uint32_t val;
/*
* This workaround needs some integration work with the HAL
* config parameters and the if_ath_pci.c glue.
* Specifically, read the value of the PCI register 0x70c
* (4 byte PCI config space register) and store it in ath_hal_war70c.
* Then if it's non-zero, the below WAR would override register
* 0x570c upon suspend/resume.
*/
#if 0
if (AR_SREV_9285E_20(ah)) {
val = AH_PRIVATE(ah)->ah_config.ath_hal_war70c;
if (val) {
val &= 0xffff00ff;
val |= 0x6f00;
OS_REG_WRITE(ah, 0x570c, val);
}
}
#endif
if (AH_PRIVATE(ah)->ah_ispcie && !restore) {
ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_pcieserdes, 1, 0);
OS_DELAY(1000);
}
/*
* Set PCIe workaround bits
*
* NOTE:
*
* In Merlin and Kite, bit 14 in WA register (disable L1) should only
* be set when device enters D3 and be cleared when device comes back
* to D0.
*/
if (power_off) { /* Power-off */
OS_REG_CLR_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
val = OS_REG_READ(ah, AR_WA);
/*
* Disable bit 6 and 7 before entering D3 to prevent
* system hang.
*/
val &= ~(AR_WA_BIT6 | AR_WA_BIT7);
/*
* See above: set AR_WA_D3_L1_DISABLE when entering D3 state.
*
* XXX The reference HAL does it this way - it only sets
* AR_WA_D3_L1_DISABLE if it's set in AR9280_WA_DEFAULT,
* which it (currently) isn't. So the following statement
* is currently a NOP.
*/
if (AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE)
val |= AR_WA_D3_L1_DISABLE;
if (AR_SREV_9285E_20(ah))
val |= AR_WA_BIT23;
OS_REG_WRITE(ah, AR_WA, val);
} else { /* Power-on */
val = AR9285_WA_DEFAULT;
/*
* See note above: make sure L1_DISABLE is not set.
*/
val &= (~AR_WA_D3_L1_DISABLE);
/* Software workaroud for ASPM system hang. */
val |= (AR_WA_BIT6 | AR_WA_BIT7);
if (AR_SREV_9285E_20(ah))
val |= AR_WA_BIT23;
OS_REG_WRITE(ah, AR_WA, val);
/* set bit 19 to allow forcing of pcie core into L1 state */
OS_REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
}
}
/*
* Take the MHz channel value and set the Channel value
*
* ASSUMES: Writes enabled to analog bus
*
* Actual Expression,
*
* For 2GHz channel,
* Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*
* For 5GHz channel,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10)
* (freq_ref = 40MHz/(24>>amodeRefSel))
*
* For 5GHz channels which are 5MHz spaced,
* Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17)
* (freq_ref = 40MHz)
*/
static HAL_BOOL
ar9287SetChannel(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
uint16_t bMode, fracMode, aModeRefSel = 0;
uint32_t freq, ndiv, channelSel = 0, channelFrac = 0, reg32 = 0;
CHAN_CENTERS centers;
uint32_t refDivA = 24;
OS_MARK(ah, AH_MARK_SETCHANNEL, chan->ic_freq);
ar5416GetChannelCenters(ah, chan, ¢ers);
freq = centers.synth_center;
reg32 = OS_REG_READ(ah, AR_PHY_SYNTH_CONTROL);
reg32 &= 0xc0000000;
if (freq < 4800) { /* 2 GHz, fractional mode */
uint32_t txctl;
int regWrites = 0;
bMode = 1;
fracMode = 1;
aModeRefSel = 0;
channelSel = (freq * 0x10000)/15;
if (AR_SREV_KIWI_11_OR_LATER(ah)) {
if (freq == 2484) {
ath_hal_ini_write(ah,
&AH9287(ah)->ah_ini_cckFirJapan2484, 1,
regWrites);
} else {
ath_hal_ini_write(ah,
&AH9287(ah)->ah_ini_cckFirNormal, 1,
regWrites);
}
}
txctl = OS_REG_READ(ah, AR_PHY_CCK_TX_CTRL);
if (freq == 2484) {
/* Enable channel spreading for channel 14 */
OS_REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
txctl | AR_PHY_CCK_TX_CTRL_JAPAN);
} else {
OS_REG_WRITE(ah, AR_PHY_CCK_TX_CTRL,
txctl &~ AR_PHY_CCK_TX_CTRL_JAPAN);
}
} else {
bMode = 0;
fracMode = 0;
if ((freq % 20) == 0) {
aModeRefSel = 3;
} else if ((freq % 10) == 0) {
aModeRefSel = 2;
} else {
aModeRefSel = 0;
/*
* Enable 2G (fractional) mode for channels which
* are 5MHz spaced
*/
fracMode = 1;
refDivA = 1;
channelSel = (freq * 0x8000)/15;
/* RefDivA setting */
OS_A_REG_RMW_FIELD(ah, AR_AN_SYNTH9,
AR_AN_SYNTH9_REFDIVA, refDivA);
}
if (!fracMode) {
ndiv = (freq * (refDivA >> aModeRefSel))/60;
channelSel = ndiv & 0x1ff;
channelFrac = (ndiv & 0xfffffe00) * 2;
channelSel = (channelSel << 17) | channelFrac;
}
}
static void
ar9280WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
int i;
const HAL_INI_ARRAY *ia;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
if (IEEE80211_IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IEEE80211_IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
} else {
freqIndex = 1;
if (IEEE80211_IS_CHAN_HT40(chan) ||
IEEE80211_IS_CHAN_TURBO(chan))
modesIndex = 2;
else
modesIndex = 1;
}
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
/*
* This is unwound because at the moment, there's a requirement
* for Merlin (and later, perhaps) to have a specific bit fixed
* in the AR_AN_TOP2 register before writing it.
*/
ia = &AH5212(ah)->ah_ini_modes;
#if 0
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes,
modesIndex, regWrites);
#endif
HALASSERT(modesIndex < ia->cols);
for (i = 0; i < ia->rows; i++) {
uint32_t reg = HAL_INI_VAL(ia, i, 0);
uint32_t val = HAL_INI_VAL(ia, i, modesIndex);
if (reg == AR_AN_TOP2 && AH5416(ah)->ah_need_an_top2_fixup)
val &= ~AR_AN_TOP2_PWDCLKIND;
OS_REG_WRITE(ah, reg, val);
/* Analog shift register delay seems needed for Merlin - PR kern/154220 */
if (reg >= 0x7800 && reg < 0x7900)
OS_DELAY(100);
DMA_YIELD(regWrites);
}
if (AR_SREV_MERLIN_20_OR_LATER(ah)) {
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_rxgain,
modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_txgain,
modesIndex, regWrites);
}
/* XXX Merlin 100us delay for shift registers */
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common,
1, regWrites);
if (AR_SREV_MERLIN_20(ah) && IS_5GHZ_FAST_CLOCK_EN(ah, chan)) {
/* 5GHz channels w/ Fast Clock use different modal values */
regWrites = ath_hal_ini_write(ah, &AH9280(ah)->ah_ini_xmodes,
modesIndex, regWrites);
}
}
static void
ar9287AniSetup(struct ath_hal *ah)
{
/*
* These are the parameters from the AR5416 ANI code;
* they likely need quite a bit of adjustment for the
* AR9280.
*/
static const struct ar5212AniParams aniparams = {
.maxNoiseImmunityLevel = 4, /* levels 0..4 */
.totalSizeDesired = { -55, -55, -55, -55, -62 },
.coarseHigh = { -14, -14, -14, -14, -12 },
.coarseLow = { -64, -64, -64, -64, -70 },
.firpwr = { -78, -78, -78, -78, -80 },
.maxSpurImmunityLevel = 2,
.cycPwrThr1 = { 2, 4, 6 },
.maxFirstepLevel = 2, /* levels 0..2 */
.firstep = { 0, 4, 8 },
.ofdmTrigHigh = 500,
.ofdmTrigLow = 200,
.cckTrigHigh = 200,
.cckTrigLow = 100,
.rssiThrHigh = 40,
.rssiThrLow = 7,
.period = 100,
};
/* NB: disable ANI noise immmunity for reliable RIFS rx */
AH5416(ah)->ah_ani_function &= ~ HAL_ANI_NOISE_IMMUNITY_LEVEL;
/* NB: ANI is not enabled yet */
ar5416AniAttach(ah, &aniparams, &aniparams, AH_TRUE);
}
/*
* Attach for an AR9287 part.
*/
static struct ath_hal *
ar9287Attach(uint16_t devid, HAL_SOFTC sc,
HAL_BUS_TAG st, HAL_BUS_HANDLE sh, uint16_t *eepromdata,
HAL_STATUS *status)
{
struct ath_hal_9287 *ahp9287;
struct ath_hal_5212 *ahp;
struct ath_hal *ah;
uint32_t val;
HAL_STATUS ecode;
HAL_BOOL rfStatus;
int8_t pwr_table_offset;
HALDEBUG(AH_NULL, HAL_DEBUG_ATTACH, "%s: sc %p st %p sh %p\n",
__func__, sc, (void*) st, (void*) sh);
/* NB: memory is returned zero'd */
ahp9287 = ath_hal_malloc(sizeof (struct ath_hal_9287));
if (ahp9287 == AH_NULL) {
HALDEBUG(AH_NULL, HAL_DEBUG_ANY,
"%s: cannot allocate memory for state block\n", __func__);
*status = HAL_ENOMEM;
return AH_NULL;
}
ahp = AH5212(ahp9287);
ah = &ahp->ah_priv.h;
ar5416InitState(AH5416(ah), devid, sc, st, sh, status);
/* XXX override with 9280 specific state */
/* override 5416 methods for our needs */
AH5416(ah)->ah_initPLL = ar9280InitPLL;
ah->ah_setAntennaSwitch = ar9287SetAntennaSwitch;
ah->ah_configPCIE = ar9287ConfigPCIE;
AH5416(ah)->ah_cal.iqCalData.calData = &ar9287_iq_cal;
AH5416(ah)->ah_cal.adcGainCalData.calData = &ar9287_adc_gain_cal;
AH5416(ah)->ah_cal.adcDcCalData.calData = &ar9287_adc_dc_cal;
AH5416(ah)->ah_cal.adcDcCalInitData.calData = &ar9287_adc_init_dc_cal;
/* Better performance without ADC Gain Calibration */
AH5416(ah)->ah_cal.suppCals = ADC_DC_CAL | IQ_MISMATCH_CAL;
AH5416(ah)->ah_spurMitigate = ar9280SpurMitigate;
AH5416(ah)->ah_writeIni = ar9287WriteIni;
ah->ah_setTxPower = ar9287SetTransmitPower;
ah->ah_setBoardValues = ar9287SetBoardValues;
AH5416(ah)->ah_olcInit = ar9287olcInit;
AH5416(ah)->ah_olcTempCompensation = ar9287olcTemperatureCompensation;
//AH5416(ah)->ah_setPowerCalTable = ar9287SetPowerCalTable;
AH5416(ah)->ah_cal_initcal = ar9287InitCalHardware;
AH5416(ah)->ah_cal_pacal = ar9287PACal;
/* XXX NF calibration */
/* XXX Ini override? (IFS vars - since the kiwi mac clock is faster?) */
/* XXX what else is kiwi-specific in the radio/calibration pathway? */
AH5416(ah)->ah_rx_chainmask = AR9287_DEFAULT_RXCHAINMASK;
AH5416(ah)->ah_tx_chainmask = AR9287_DEFAULT_TXCHAINMASK;
if (!ar5416SetResetReg(ah, HAL_RESET_POWER_ON)) {
/* reset chip */
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't reset chip\n",
__func__);
ecode = HAL_EIO;
goto bad;
}
if (!ar5416SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: couldn't wakeup chip\n",
__func__);
ecode = HAL_EIO;
goto bad;
}
/* Read Revisions from Chips before taking out of reset */
val = OS_REG_READ(ah, AR_SREV);
HALDEBUG(ah, HAL_DEBUG_ATTACH,
"%s: ID 0x%x VERSION 0x%x TYPE 0x%x REVISION 0x%x\n",
__func__, MS(val, AR_XSREV_ID), MS(val, AR_XSREV_VERSION),
MS(val, AR_XSREV_TYPE), MS(val, AR_XSREV_REVISION));
/* NB: include chip type to differentiate from pre-Sowl versions */
AH_PRIVATE(ah)->ah_macVersion =
(val & AR_XSREV_VERSION) >> AR_XSREV_TYPE_S;
AH_PRIVATE(ah)->ah_macRev = MS(val, AR_XSREV_REVISION);
AH_PRIVATE(ah)->ah_ispcie = (val & AR_XSREV_TYPE_HOST_MODE) == 0;
/* Don't support Kiwi < 1.2; those are pre-release chips */
if (! AR_SREV_KIWI_12_OR_LATER(ah)) {
ath_hal_printf(ah, "[ath]: Kiwi < 1.2 is not supported\n");
ecode = HAL_EIO;
goto bad;
}
/* setup common ini data; rf backends handle remainder */
HAL_INI_INIT(&ahp->ah_ini_modes, ar9287Modes_9287_1_1, 6);
HAL_INI_INIT(&ahp->ah_ini_common, ar9287Common_9287_1_1, 2);
/* If pcie_clock_req */
HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
ar9287PciePhy_clkreq_always_on_L1_9287_1_1, 2);
/* XXX WoW ini values */
/* Else */
#if 0
HAL_INI_INIT(&AH5416(ah)->ah_ini_pcieserdes,
ar9287PciePhy_clkreq_off_L1_9287_1_1, 2);
#endif
/* Initialise Japan arrays */
HAL_INI_INIT(&ahp9287->ah_ini_cckFirNormal,
ar9287Common_normal_cck_fir_coeff_9287_1_1, 2);
HAL_INI_INIT(&ahp9287->ah_ini_cckFirJapan2484,
ar9287Common_japan_2484_cck_fir_coeff_9287_1_1, 2);
ar5416AttachPCIE(ah);
ecode = ath_hal_9287EepromAttach(ah);
if (ecode != HAL_OK)
goto bad;
if (!ar5416ChipReset(ah, AH_NULL)) { /* reset chip */
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n", __func__);
ecode = HAL_EIO;
goto bad;
}
AH_PRIVATE(ah)->ah_phyRev = OS_REG_READ(ah, AR_PHY_CHIP_ID);
if (!ar5212ChipTest(ah)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: hardware self-test failed\n",
__func__);
ecode = HAL_ESELFTEST;
goto bad;
}
/*
* Set correct Baseband to analog shift
* setting to access analog chips.
*/
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
/* Read Radio Chip Rev Extract */
AH_PRIVATE(ah)->ah_analog5GhzRev = ar5416GetRadioRev(ah);
switch (AH_PRIVATE(ah)->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR) {
case AR_RAD2133_SREV_MAJOR: /* Sowl: 2G/3x3 */
case AR_RAD5133_SREV_MAJOR: /* Sowl: 2+5G/3x3 */
break;
default:
if (AH_PRIVATE(ah)->ah_analog5GhzRev == 0) {
AH_PRIVATE(ah)->ah_analog5GhzRev =
AR_RAD5133_SREV_MAJOR;
break;
}
#ifdef AH_DEBUG
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: 5G Radio Chip Rev 0x%02X is not supported by "
"this driver\n", __func__,
AH_PRIVATE(ah)->ah_analog5GhzRev);
ecode = HAL_ENOTSUPP;
goto bad;
#endif
}
rfStatus = ar9287RfAttach(ah, &ecode);
if (!rfStatus) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: RF setup failed, status %u\n",
__func__, ecode);
goto bad;
}
/*
* We only implement open-loop TX power control
* for the AR9287 in this codebase.
*/
if (! ath_hal_eepromGetFlag(ah, AR_EEP_OL_PWRCTRL)) {
ath_hal_printf(ah, "[ath] AR9287 w/ closed-loop TX power control"
" isn't supported.\n");
ecode = HAL_ENOTSUPP;
goto bad;
}
/*
* Check whether the power table offset isn't the default.
* This can occur with eeprom minor V21 or greater on Merlin.
*/
(void) ath_hal_eepromGet(ah, AR_EEP_PWR_TABLE_OFFSET, &pwr_table_offset);
if (pwr_table_offset != AR5416_PWR_TABLE_OFFSET_DB)
ath_hal_printf(ah, "[ath]: default pwr offset: %d dBm != EEPROM pwr offset: %d dBm; curves will be adjusted.\n",
AR5416_PWR_TABLE_OFFSET_DB, (int) pwr_table_offset);
/* setup rxgain table */
HAL_INI_INIT(&ahp9287->ah_ini_rxgain, ar9287Modes_rx_gain_9287_1_1, 6);
/* setup txgain table */
HAL_INI_INIT(&ahp9287->ah_ini_txgain, ar9287Modes_tx_gain_9287_1_1, 6);
/*
* Got everything we need now to setup the capabilities.
*/
if (!ar9287FillCapabilityInfo(ah)) {
ecode = HAL_EEREAD;
goto bad;
}
ecode = ath_hal_eepromGet(ah, AR_EEP_MACADDR, ahp->ah_macaddr);
if (ecode != HAL_OK) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error getting mac address from EEPROM\n", __func__);
goto bad;
}
/* XXX How about the serial number ? */
/* Read Reg Domain */
AH_PRIVATE(ah)->ah_currentRD =
ath_hal_eepromGet(ah, AR_EEP_REGDMN_0, AH_NULL);
AH_PRIVATE(ah)->ah_currentRDext = AR9287_RDEXT_DEFAULT;
/*
* ah_miscMode is populated by ar5416FillCapabilityInfo()
* starting from griffin. Set here to make sure that
* AR_MISC_MODE_MIC_NEW_LOC_ENABLE is set before a GTK is
* placed into hardware.
*/
if (ahp->ah_miscMode != 0)
OS_REG_WRITE(ah, AR_MISC_MODE, OS_REG_READ(ah, AR_MISC_MODE) | ahp->ah_miscMode);
ar9287AniSetup(ah); /* Anti Noise Immunity */
/* Setup noise floor min/max/nominal values */
AH5416(ah)->nf_2g.max = AR_PHY_CCA_MAX_GOOD_VAL_9287_2GHZ;
AH5416(ah)->nf_2g.min = AR_PHY_CCA_MIN_GOOD_VAL_9287_2GHZ;
AH5416(ah)->nf_2g.nominal = AR_PHY_CCA_NOM_VAL_9287_2GHZ;
AH5416(ah)->nf_5g.max = AR_PHY_CCA_MAX_GOOD_VAL_9287_5GHZ;
AH5416(ah)->nf_5g.min = AR_PHY_CCA_MIN_GOOD_VAL_9287_5GHZ;
AH5416(ah)->nf_5g.nominal = AR_PHY_CCA_NOM_VAL_9287_5GHZ;
ar5416InitNfHistBuff(AH5416(ah)->ah_cal.nfCalHist);
HALDEBUG(ah, HAL_DEBUG_ATTACH, "%s: return\n", __func__);
return ah;
bad:
if (ah != AH_NULL)
ah->ah_detach(ah);
if (status)
*status = ecode;
return AH_NULL;
}
static void
ar9287ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore)
{
if (AH_PRIVATE(ah)->ah_ispcie && !restore) {
ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_pcieserdes, 1, 0);
OS_DELAY(1000);
OS_REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
OS_REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT); /* Yes, Kiwi uses the Kite PCIe PHY WA */
}
}
static void
ar9287WriteIni(struct ath_hal *ah, const struct ieee80211_channel *chan)
{
u_int modesIndex, freqIndex;
int regWrites = 0;
/* Setup the indices for the next set of register array writes */
/* XXX Ignore 11n dynamic mode on the AR5416 for the moment */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
if (IEEE80211_IS_CHAN_HT40(chan))
modesIndex = 3;
else if (IEEE80211_IS_CHAN_108G(chan))
modesIndex = 5;
else
modesIndex = 4;
} else {
freqIndex = 1;
if (IEEE80211_IS_CHAN_HT40(chan) ||
IEEE80211_IS_CHAN_TURBO(chan))
modesIndex = 2;
else
modesIndex = 1;
}
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
OS_REG_WRITE(ah, AR_PHY_ADC_SERIAL_CTL, AR_PHY_SEL_INTERNAL_ADDAC);
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_modes, modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH9287(ah)->ah_ini_rxgain, modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH9287(ah)->ah_ini_txgain, modesIndex, regWrites);
regWrites = ath_hal_ini_write(ah, &AH5212(ah)->ah_ini_common, 1, regWrites);
}
/*
* Places the device in and out of reset and then places sane
* values in the registers based on EEPROM config, initialization
* vectors (as determined by the mode), and station configuration
*
* bChannelChange is used to preserve DMA/PCU registers across
* a HW Reset during channel change.
*/
HAL_BOOL
ar5312Reset(struct ath_hal *ah, HAL_OPMODE opmode,
struct ieee80211_channel *chan,
HAL_BOOL bChannelChange,
HAL_RESET_TYPE resetType,
HAL_STATUS *status)
{
#define N(a) (sizeof (a) / sizeof (a[0]))
#define FAIL(_code) do { ecode = _code; goto bad; } while (0)
struct ath_hal_5212 *ahp = AH5212(ah);
HAL_CHANNEL_INTERNAL *ichan;
const HAL_EEPROM *ee;
uint32_t saveFrameSeqCount, saveDefAntenna;
uint32_t macStaId1, synthDelay, txFrm2TxDStart;
uint16_t rfXpdGain[MAX_NUM_PDGAINS_PER_CHANNEL];
int16_t cckOfdmPwrDelta = 0;
u_int modesIndex, freqIndex;
HAL_STATUS ecode;
int i, regWrites = 0;
uint32_t testReg;
uint32_t saveLedState = 0;
HALASSERT(ah->ah_magic == AR5212_MAGIC);
ee = AH_PRIVATE(ah)->ah_eeprom;
OS_MARK(ah, AH_MARK_RESET, bChannelChange);
/*
* Map public channel to private.
*/
ichan = ath_hal_checkchannel(ah, chan);
if (ichan == AH_NULL) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: invalid channel %u/0x%x; no mapping\n",
__func__, chan->ic_freq, chan->ic_flags);
FAIL(HAL_EINVAL);
}
switch (opmode) {
case HAL_M_STA:
case HAL_M_IBSS:
case HAL_M_HOSTAP:
case HAL_M_MONITOR:
break;
default:
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: invalid operating mode %u\n",
__func__, opmode);
FAIL(HAL_EINVAL);
break;
}
HALASSERT(ahp->ah_eeversion >= AR_EEPROM_VER3);
/* Preserve certain DMA hardware registers on a channel change */
if (bChannelChange) {
/*
* On Venice, the TSF is almost preserved across a reset;
* it requires the doubling writes to the RESET_TSF
* bit in the AR_BEACON register; it also has the quirk
* of the TSF going back in time on the station (station
* latches onto the last beacon's tsf during a reset 50%
* of the times); the latter is not a problem for adhoc
* stations since as long as the TSF is behind, it will
* get resynchronized on receiving the next beacon; the
* TSF going backwards in time could be a problem for the
* sleep operation (supported on infrastructure stations
* only) - the best and most general fix for this situation
* is to resynchronize the various sleep/beacon timers on
* the receipt of the next beacon i.e. when the TSF itself
* gets resynchronized to the AP's TSF - power save is
* needed to be temporarily disabled until that time
*
* Need to save the sequence number to restore it after
* the reset!
*/
saveFrameSeqCount = OS_REG_READ(ah, AR_D_SEQNUM);
} else
saveFrameSeqCount = 0; /* NB: silence compiler */
/* If the channel change is across the same mode - perform a fast channel change */
if ((IS_2413(ah) || IS_5413(ah))) {
/*
* Channel change can only be used when:
* -channel change requested - so it's not the initial reset.
* -it's not a change to the current channel - often called when switching modes
* on a channel
* -the modes of the previous and requested channel are the same - some ugly code for XR
*/
if (bChannelChange &&
AH_PRIVATE(ah)->ah_curchan != AH_NULL &&
(chan->ic_freq != AH_PRIVATE(ah)->ah_curchan->ic_freq) &&
((chan->ic_flags & IEEE80211_CHAN_ALLTURBO) ==
(AH_PRIVATE(ah)->ah_curchan->ic_flags & IEEE80211_CHAN_ALLTURBO))) {
if (ar5212ChannelChange(ah, chan))
/* If ChannelChange completed - skip the rest of reset */
return AH_TRUE;
}
}
/*
* Preserve the antenna on a channel change
*/
saveDefAntenna = OS_REG_READ(ah, AR_DEF_ANTENNA);
if (saveDefAntenna == 0) /* XXX magic constants */
saveDefAntenna = 1;
/* Save hardware flag before chip reset clears the register */
macStaId1 = OS_REG_READ(ah, AR_STA_ID1) &
(AR_STA_ID1_BASE_RATE_11B | AR_STA_ID1_USE_DEFANT);
/* Save led state from pci config register */
if (!IS_5315(ah))
saveLedState = OS_REG_READ(ah, AR5312_PCICFG) &
(AR_PCICFG_LEDCTL | AR_PCICFG_LEDMODE | AR_PCICFG_LEDBLINK |
AR_PCICFG_LEDSLOW);
ar5312RestoreClock(ah, opmode); /* move to refclk operation */
/*
* Adjust gain parameters before reset if
* there's an outstanding gain updated.
*/
(void) ar5212GetRfgain(ah);
if (!ar5312ChipReset(ah, chan)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: chip reset failed\n", __func__);
FAIL(HAL_EIO);
}
/* Setup the indices for the next set of register array writes */
if (IEEE80211_IS_CHAN_2GHZ(chan)) {
freqIndex = 2;
modesIndex = IEEE80211_IS_CHAN_108G(chan) ? 5 :
IEEE80211_IS_CHAN_G(chan) ? 4 : 3;
} else {
freqIndex = 1;
modesIndex = IEEE80211_IS_CHAN_ST(chan) ? 2 : 1;
}
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
/* Set correct Baseband to analog shift setting to access analog chips. */
OS_REG_WRITE(ah, AR_PHY(0), 0x00000007);
regWrites = ath_hal_ini_write(ah, &ahp->ah_ini_modes, modesIndex, 0);
regWrites = write_common(ah, &ahp->ah_ini_common, bChannelChange,
regWrites);
ahp->ah_rfHal->writeRegs(ah, modesIndex, freqIndex, regWrites);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
if (IEEE80211_IS_CHAN_HALF(chan) || IEEE80211_IS_CHAN_QUARTER(chan))
ar5212SetIFSTiming(ah, chan);
/* Overwrite INI values for revised chipsets */
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_2) {
/* ADC_CTL */
OS_REG_WRITE(ah, AR_PHY_ADC_CTL,
SM(2, AR_PHY_ADC_CTL_OFF_INBUFGAIN) |
SM(2, AR_PHY_ADC_CTL_ON_INBUFGAIN) |
AR_PHY_ADC_CTL_OFF_PWDDAC |
AR_PHY_ADC_CTL_OFF_PWDADC);
/* TX_PWR_ADJ */
if (chan->channel == 2484) {
cckOfdmPwrDelta = SCALE_OC_DELTA(ee->ee_cckOfdmPwrDelta - ee->ee_scaledCh14FilterCckDelta);
} else {
cckOfdmPwrDelta = SCALE_OC_DELTA(ee->ee_cckOfdmPwrDelta);
}
if (IEEE80211_IS_CHAN_G(chan)) {
OS_REG_WRITE(ah, AR_PHY_TXPWRADJ,
SM((ee->ee_cckOfdmPwrDelta*-1), AR_PHY_TXPWRADJ_CCK_GAIN_DELTA) |
SM((cckOfdmPwrDelta*-1), AR_PHY_TXPWRADJ_CCK_PCDAC_INDEX));
} else {
OS_REG_WRITE(ah, AR_PHY_TXPWRADJ, 0);
}
/* Add barker RSSI thresh enable as disabled */
OS_REG_CLR_BIT(ah, AR_PHY_DAG_CTRLCCK,
AR_PHY_DAG_CTRLCCK_EN_RSSI_THR);
OS_REG_RMW_FIELD(ah, AR_PHY_DAG_CTRLCCK,
AR_PHY_DAG_CTRLCCK_RSSI_THR, 2);
/* Set the mute mask to the correct default */
OS_REG_WRITE(ah, AR_SEQ_MASK, 0x0000000F);
}
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_3) {
/* Clear reg to alllow RX_CLEAR line debug */
OS_REG_WRITE(ah, AR_PHY_BLUETOOTH, 0);
}
if (AH_PRIVATE(ah)->ah_phyRev >= AR_PHY_CHIP_ID_REV_4) {
#ifdef notyet
/* Enable burst prefetch for the data queues */
OS_REG_RMW_FIELD(ah, AR_D_FPCTL, ... );
/* Enable double-buffering */
OS_REG_CLR_BIT(ah, AR_TXCFG, AR_TXCFG_DBL_BUF_DIS);
#endif
}
if (IS_5312_2_X(ah)) {
/* ADC_CTRL */
OS_REG_WRITE(ah, AR_PHY_SIGMA_DELTA,
SM(2, AR_PHY_SIGMA_DELTA_ADC_SEL) |
SM(4, AR_PHY_SIGMA_DELTA_FILT2) |
SM(0x16, AR_PHY_SIGMA_DELTA_FILT1) |
SM(0, AR_PHY_SIGMA_DELTA_ADC_CLIP));
if (IEEE80211_IS_CHAN_2GHZ(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_RXGAIN, AR_PHY_RXGAIN_TXRX_RF_MAX, 0x0F);
/* CCK Short parameter adjustment in 11B mode */
if (IEEE80211_IS_CHAN_B(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_CCK_RXCTRL4, AR_PHY_CCK_RXCTRL4_FREQ_EST_SHORT, 12);
/* Set ADC/DAC select values */
OS_REG_WRITE(ah, AR_PHY_SLEEP_SCAL, 0x04);
/* Increase 11A AGC Settling */
if (IEEE80211_IS_CHAN_A(chan))
OS_REG_RMW_FIELD(ah, AR_PHY_SETTLING, AR_PHY_SETTLING_AGC, 32);
} else {
/* Set ADC/DAC select values */
OS_REG_WRITE(ah, AR_PHY_SLEEP_SCAL, 0x0e);
}
/* Setup the transmit power values. */
if (!ar5212SetTransmitPower(ah, chan, rfXpdGain)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error init'ing transmit power\n", __func__);
FAIL(HAL_EIO);
}
/* Write the analog registers */
if (!ahp->ah_rfHal->setRfRegs(ah, chan, modesIndex, rfXpdGain)) {
HALDEBUG(ah, HAL_DEBUG_ANY, "%s: ar5212SetRfRegs failed\n",
__func__);
FAIL(HAL_EIO);
}
/* Write delta slope for OFDM enabled modes (A, G, Turbo) */
if (IEEE80211_IS_CHAN_OFDM(chan)) {
if (IS_5413(ah) ||
AH_PRIVATE(ah)->ah_eeversion >= AR_EEPROM_VER5_3)
ar5212SetSpurMitigation(ah, chan);
ar5212SetDeltaSlope(ah, chan);
}
/* Setup board specific options for EEPROM version 3 */
if (!ar5212SetBoardValues(ah, chan)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: error setting board options\n", __func__);
FAIL(HAL_EIO);
}
/* Restore certain DMA hardware registers on a channel change */
if (bChannelChange)
OS_REG_WRITE(ah, AR_D_SEQNUM, saveFrameSeqCount);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
OS_REG_WRITE(ah, AR_STA_ID0, LE_READ_4(ahp->ah_macaddr));
OS_REG_WRITE(ah, AR_STA_ID1, LE_READ_2(ahp->ah_macaddr + 4)
| macStaId1
| AR_STA_ID1_RTS_USE_DEF
| ahp->ah_staId1Defaults
);
ar5212SetOperatingMode(ah, opmode);
/* Set Venice BSSID mask according to current state */
OS_REG_WRITE(ah, AR_BSSMSKL, LE_READ_4(ahp->ah_bssidmask));
OS_REG_WRITE(ah, AR_BSSMSKU, LE_READ_2(ahp->ah_bssidmask + 4));
/* Restore previous led state */
if (!IS_5315(ah))
OS_REG_WRITE(ah, AR5312_PCICFG, OS_REG_READ(ah, AR_PCICFG) | saveLedState);
/* Restore previous antenna */
OS_REG_WRITE(ah, AR_DEF_ANTENNA, saveDefAntenna);
/* then our BSSID */
OS_REG_WRITE(ah, AR_BSS_ID0, LE_READ_4(ahp->ah_bssid));
OS_REG_WRITE(ah, AR_BSS_ID1, LE_READ_2(ahp->ah_bssid + 4));
/* Restore bmiss rssi & count thresholds */
OS_REG_WRITE(ah, AR_RSSI_THR, ahp->ah_rssiThr);
OS_REG_WRITE(ah, AR_ISR, ~0); /* cleared on write */
if (!ar5212SetChannel(ah, chan))
FAIL(HAL_EIO);
OS_MARK(ah, AH_MARK_RESET_LINE, __LINE__);
ar5212SetCoverageClass(ah, AH_PRIVATE(ah)->ah_coverageClass, 1);
ar5212SetRateDurationTable(ah, chan);
/* Set Tx frame start to tx data start delay */
if (IS_RAD5112_ANY(ah) &&
(IEEE80211_IS_CHAN_HALF(chan) || IEEE80211_IS_CHAN_QUARTER(chan))) {
txFrm2TxDStart =
IEEE80211_IS_CHAN_HALF(chan) ?
TX_FRAME_D_START_HALF_RATE:
TX_FRAME_D_START_QUARTER_RATE;
OS_REG_RMW_FIELD(ah, AR_PHY_TX_CTL,
AR_PHY_TX_FRAME_TO_TX_DATA_START, txFrm2TxDStart);
}
/*
* Setup fast diversity.
* Fast diversity can be enabled or disabled via regadd.txt.
* Default is enabled.
* For reference,
* Disable: reg val
* 0x00009860 0x00009d18 (if 11a / 11g, else no change)
* 0x00009970 0x192bb514
* 0x0000a208 0xd03e4648
*
* Enable: 0x00009860 0x00009d10 (if 11a / 11g, else no change)
* 0x00009970 0x192fb514
* 0x0000a208 0xd03e6788
*/
/* XXX Setup pre PHY ENABLE EAR additions */
/* flush SCAL reg */
if (IS_5312_2_X(ah)) {
(void) OS_REG_READ(ah, AR_PHY_SLEEP_SCAL);
}
/*
* Wait for the frequency synth to settle (synth goes on
* via AR_PHY_ACTIVE_EN). Read the phy active delay register.
* Value is in 100ns increments.
*/
synthDelay = OS_REG_READ(ah, AR_PHY_RX_DELAY) & AR_PHY_RX_DELAY_DELAY;
if (IEEE80211_IS_CHAN_B(chan)) {
synthDelay = (4 * synthDelay) / 22;
} else {
synthDelay /= 10;
}
/* Activate the PHY (includes baseband activate and synthesizer on) */
OS_REG_WRITE(ah, AR_PHY_ACTIVE, AR_PHY_ACTIVE_EN);
/*
* There is an issue if the AP starts the calibration before
* the base band timeout completes. This could result in the
* rx_clear false triggering. As a workaround we add delay an
* extra BASE_ACTIVATE_DELAY usecs to ensure this condition
* does not happen.
*/
if (IEEE80211_IS_CHAN_HALF(chan)) {
OS_DELAY((synthDelay << 1) + BASE_ACTIVATE_DELAY);
} else if (IEEE80211_IS_CHAN_QUARTER(chan)) {
OS_DELAY((synthDelay << 2) + BASE_ACTIVATE_DELAY);
} else {
OS_DELAY(synthDelay + BASE_ACTIVATE_DELAY);
}
/*
* The udelay method is not reliable with notebooks.
* Need to check to see if the baseband is ready
*/
testReg = OS_REG_READ(ah, AR_PHY_TESTCTRL);
/* Selects the Tx hold */
OS_REG_WRITE(ah, AR_PHY_TESTCTRL, AR_PHY_TESTCTRL_TXHOLD);
i = 0;
while ((i++ < 20) &&
(OS_REG_READ(ah, 0x9c24) & 0x10)) /* test if baseband not ready */ OS_DELAY(200);
OS_REG_WRITE(ah, AR_PHY_TESTCTRL, testReg);
/* Calibrate the AGC and start a NF calculation */
OS_REG_WRITE(ah, AR_PHY_AGC_CONTROL,
OS_REG_READ(ah, AR_PHY_AGC_CONTROL)
| AR_PHY_AGC_CONTROL_CAL
| AR_PHY_AGC_CONTROL_NF);
if (!IEEE80211_IS_CHAN_B(chan) && ahp->ah_bIQCalibration != IQ_CAL_DONE) {
/* Start IQ calibration w/ 2^(INIT_IQCAL_LOG_COUNT_MAX+1) samples */
OS_REG_RMW_FIELD(ah, AR_PHY_TIMING_CTRL4,
AR_PHY_TIMING_CTRL4_IQCAL_LOG_COUNT_MAX,
INIT_IQCAL_LOG_COUNT_MAX);
OS_REG_SET_BIT(ah, AR_PHY_TIMING_CTRL4,
AR_PHY_TIMING_CTRL4_DO_IQCAL);
ahp->ah_bIQCalibration = IQ_CAL_RUNNING;
} else
ahp->ah_bIQCalibration = IQ_CAL_INACTIVE;
/* Setup compression registers */
ar5212SetCompRegs(ah);
/* Set 1:1 QCU to DCU mapping for all queues */
for (i = 0; i < AR_NUM_DCU; i++)
OS_REG_WRITE(ah, AR_DQCUMASK(i), 1 << i);
ahp->ah_intrTxqs = 0;
for (i = 0; i < AH_PRIVATE(ah)->ah_caps.halTotalQueues; i++)
ar5212ResetTxQueue(ah, i);
/*
* Setup interrupt handling. Note that ar5212ResetTxQueue
* manipulates the secondary IMR's as queues are enabled
* and disabled. This is done with RMW ops to insure the
* settings we make here are preserved.
*/
ahp->ah_maskReg = AR_IMR_TXOK | AR_IMR_TXERR | AR_IMR_TXURN
| AR_IMR_RXOK | AR_IMR_RXERR | AR_IMR_RXORN
| AR_IMR_HIUERR
;
if (opmode == HAL_M_HOSTAP)
ahp->ah_maskReg |= AR_IMR_MIB;
OS_REG_WRITE(ah, AR_IMR, ahp->ah_maskReg);
/* Enable bus errors that are OR'd to set the HIUERR bit */
OS_REG_WRITE(ah, AR_IMR_S2,
OS_REG_READ(ah, AR_IMR_S2)
| AR_IMR_S2_MCABT | AR_IMR_S2_SSERR | AR_IMR_S2_DPERR);
if (AH_PRIVATE(ah)->ah_rfkillEnabled)
ar5212EnableRfKill(ah);
if (!ath_hal_wait(ah, AR_PHY_AGC_CONTROL, AR_PHY_AGC_CONTROL_CAL, 0)) {
HALDEBUG(ah, HAL_DEBUG_ANY,
"%s: offset calibration failed to complete in 1ms;"
" noisy environment?\n", __func__);
}
/*
* Set clocks back to 32kHz if they had been using refClk, then
* use an external 32kHz crystal when sleeping, if one exists.
*/
ar5312SetupClock(ah, opmode);
/*
* Writing to AR_BEACON will start timers. Hence it should
* be the last register to be written. Do not reset tsf, do
* not enable beacons at this point, but preserve other values
* like beaconInterval.
*/
OS_REG_WRITE(ah, AR_BEACON,
(OS_REG_READ(ah, AR_BEACON) &~ (AR_BEACON_EN | AR_BEACON_RESET_TSF)));
/* XXX Setup post reset EAR additions */
/* QoS support */
if (AH_PRIVATE(ah)->ah_macVersion > AR_SREV_VERSION_VENICE ||
(AH_PRIVATE(ah)->ah_macVersion == AR_SREV_VERSION_VENICE &&
AH_PRIVATE(ah)->ah_macRev >= AR_SREV_GRIFFIN_LITE)) {
OS_REG_WRITE(ah, AR_QOS_CONTROL, 0x100aa); /* XXX magic */
OS_REG_WRITE(ah, AR_QOS_SELECT, 0x3210); /* XXX magic */
}
/* Turn on NOACK Support for QoS packets */
OS_REG_WRITE(ah, AR_NOACK,
SM(2, AR_NOACK_2BIT_VALUE) |
SM(5, AR_NOACK_BIT_OFFSET) |
SM(0, AR_NOACK_BYTE_OFFSET));
/* Restore user-specified settings */
if (ahp->ah_miscMode != 0)
OS_REG_WRITE(ah, AR_MISC_MODE, ahp->ah_miscMode);
if (ahp->ah_slottime != (u_int) -1)
ar5212SetSlotTime(ah, ahp->ah_slottime);
if (ahp->ah_acktimeout != (u_int) -1)
ar5212SetAckTimeout(ah, ahp->ah_acktimeout);
if (ahp->ah_ctstimeout != (u_int) -1)
ar5212SetCTSTimeout(ah, ahp->ah_ctstimeout);
if (ahp->ah_sifstime != (u_int) -1)
ar5212SetSifsTime(ah, ahp->ah_sifstime);
if (AH_PRIVATE(ah)->ah_diagreg != 0)
OS_REG_WRITE(ah, AR_DIAG_SW, AH_PRIVATE(ah)->ah_diagreg);
AH_PRIVATE(ah)->ah_opmode = opmode; /* record operating mode */
if (bChannelChange && !IEEE80211_IS_CHAN_DFS(chan))
chan->ic_state &= ~IEEE80211_CHANSTATE_CWINT;
HALDEBUG(ah, HAL_DEBUG_RESET, "%s: done\n", __func__);
OS_MARK(ah, AH_MARK_RESET_DONE, 0);
return AH_TRUE;
bad:
OS_MARK(ah, AH_MARK_RESET_DONE, ecode);
if (status != AH_NULL)
*status = ecode;
return AH_FALSE;
#undef FAIL
#undef N
}
static void
ar9280ConfigPCIE(struct ath_hal *ah, HAL_BOOL restore, HAL_BOOL power_off)
{
uint32_t val;
if (AH_PRIVATE(ah)->ah_ispcie && !restore) {
ath_hal_ini_write(ah, &AH5416(ah)->ah_ini_pcieserdes, 1, 0);
OS_DELAY(1000);
}
/*
* Set PCIe workaround bits
*
* NOTE:
*
* In Merlin and Kite, bit 14 in WA register (disable L1) should only
* be set when device enters D3 and be cleared when device comes back
* to D0.
*/
if (power_off) { /* Power-off */
OS_REG_CLR_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
val = OS_REG_READ(ah, AR_WA);
/*
* Disable bit 6 and 7 before entering D3 to prevent
* system hang.
*/
val &= ~(AR_WA_BIT6 | AR_WA_BIT7);
/*
* XXX Not sure, is specified in the reference HAL.
*/
val |= AR_WA_BIT22;
/*
* See above: set AR_WA_D3_L1_DISABLE when entering D3 state.
*
* XXX The reference HAL does it this way - it only sets
* AR_WA_D3_L1_DISABLE if it's set in AR9280_WA_DEFAULT,
* which it (currently) isn't. So the following statement
* is currently a NOP.
*/
if (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE)
val |= AR_WA_D3_L1_DISABLE;
OS_REG_WRITE(ah, AR_WA, val);
} else { /* Power-on */
val = AR9280_WA_DEFAULT;
/*
* See note above: make sure L1_DISABLE is not set.
*/
val &= (~AR_WA_D3_L1_DISABLE);
OS_REG_WRITE(ah, AR_WA, val);
/* set bit 19 to allow forcing of pcie core into L1 state */
OS_REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
}
}
