static int
isp1301_set_peripheral(struct otg_transceiver *otg, struct usb_gadget *gadget)
{
struct isp1301 *isp = container_of(otg, struct isp1301, otg);
if (!otg || isp != the_transceiver)
return -ENODEV;
if (!gadget) {
OTG_IRQ_EN_REG = 0;
if (!isp->otg.default_a)
enable_vbus_draw(isp, 0);
usb_gadget_vbus_disconnect(isp->otg.gadget);
isp->otg.gadget = 0;
power_down(isp);
return 0;
}
#ifdef CONFIG_USB_OTG
isp->otg.gadget = gadget;
dev_dbg(&isp->client.dev, "registered gadget\n");
/* gadget driver may be suspended until vbus_connect () */
if (isp->otg.host)
return isp1301_otg_enable(isp);
return 0;
#elif !defined(CONFIG_USB_OHCI_HCD) && !defined(CONFIG_USB_OHCI_HCD_MODULE)
isp->otg.gadget = gadget;
// FIXME update its refcount
OTG_CTRL_REG = (OTG_CTRL_REG & OTG_CTRL_MASK
& ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS))
| OTG_ID;
power_up(isp);
isp->otg.state = OTG_STATE_B_IDLE;
if (machine_is_omap_h2())
isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
INTR_SESS_VLD);
isp1301_set_bits(isp, ISP1301_INTERRUPT_FALLING,
INTR_VBUS_VLD);
dev_info(&isp->client.dev, "B-Peripheral sessions ok\n");
dump_regs(isp, __func__);
/* If this has a Mini-AB connector, this mode is highly
* nonstandard ... but can be handy for testing, so long
* as you don't plug a Mini-A cable into the jack.
*/
if (isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE) & INTR_VBUS_VLD)
b_peripheral(isp);
return 0;
#else
dev_dbg(&isp->client.dev, "peripheral sessions not allowed\n");
return -EINVAL;
#endif
}
static void isp_update_otg(struct isp1301 *isp, u8 stat)
{
u8 isp_stat, isp_bstat;
enum usb_otg_state state = isp->otg.state;
if (stat & INTR_BDIS_ACON)
pr_debug("OTG: BDIS_ACON, %s\n", state_name(isp));
/* start certain state transitions right away */
isp_stat = isp1301_get_u8(isp, ISP1301_INTERRUPT_SOURCE);
if (isp_stat & INTR_ID_GND) {
if (isp->otg.default_a) {
switch (state) {
case OTG_STATE_B_IDLE:
a_idle(isp, "idle");
/* FALLTHROUGH */
case OTG_STATE_A_IDLE:
enable_vbus_source(isp);
/* FALLTHROUGH */
case OTG_STATE_A_WAIT_VRISE:
/* we skip over OTG_STATE_A_WAIT_BCON, since
* the HC will transition to A_HOST (or
* A_SUSPEND!) without our noticing except
* when HNP is used.
*/
if (isp_stat & INTR_VBUS_VLD)
isp->otg.state = OTG_STATE_A_HOST;
break;
case OTG_STATE_A_WAIT_VFALL:
if (!(isp_stat & INTR_SESS_VLD))
a_idle(isp, "vfell");
break;
default:
if (!(isp_stat & INTR_VBUS_VLD))
isp->otg.state = OTG_STATE_A_VBUS_ERR;
break;
}
isp_bstat = isp1301_get_u8(isp, ISP1301_OTG_STATUS);
} else {
switch (state) {
case OTG_STATE_B_PERIPHERAL:
case OTG_STATE_B_HOST:
case OTG_STATE_B_WAIT_ACON:
usb_gadget_vbus_disconnect(isp->otg.gadget);
break;
default:
break;
}
if (state != OTG_STATE_A_IDLE)
a_idle(isp, "id");
if (isp->otg.host && state == OTG_STATE_A_IDLE)
isp1301_defer_work(isp, WORK_HOST_RESUME);
isp_bstat = 0;
}
} else {
u32 l;
/* if user unplugged mini-A end of cable,
* don't bypass A_WAIT_VFALL.
*/
if (isp->otg.default_a) {
switch (state) {
default:
isp->otg.state = OTG_STATE_A_WAIT_VFALL;
break;
case OTG_STATE_A_WAIT_VFALL:
state = OTG_STATE_A_IDLE;
/* khubd may take a while to notice and
* handle this disconnect, so don't go
* to B_IDLE quite yet.
*/
break;
case OTG_STATE_A_IDLE:
host_suspend(isp);
isp1301_clear_bits(isp, ISP1301_MODE_CONTROL_1,
MC1_BDIS_ACON_EN);
isp->otg.state = OTG_STATE_B_IDLE;
l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
l &= ~OTG_CTRL_BITS;
omap_writel(l, OTG_CTRL);
break;
case OTG_STATE_B_IDLE:
break;
}
}
isp_bstat = isp1301_get_u8(isp, ISP1301_OTG_STATUS);
switch (isp->otg.state) {
case OTG_STATE_B_PERIPHERAL:
case OTG_STATE_B_WAIT_ACON:
case OTG_STATE_B_HOST:
if (likely(isp_bstat & OTG_B_SESS_VLD))
break;
enable_vbus_draw(isp, 0);
#ifndef CONFIG_USB_OTG
/* UDC driver will clear OTG_BSESSVLD */
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DP_PULLDOWN);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1,
OTG1_DP_PULLUP);
dump_regs(isp, __func__);
#endif
/* FALLTHROUGH */
case OTG_STATE_B_SRP_INIT:
b_idle(isp, __func__);
l = omap_readl(OTG_CTRL) & OTG_XCEIV_OUTPUTS;
omap_writel(l, OTG_CTRL);
/* FALLTHROUGH */
case OTG_STATE_B_IDLE:
if (isp->otg.gadget && (isp_bstat & OTG_B_SESS_VLD)) {
#ifdef CONFIG_USB_OTG
update_otg1(isp, isp_stat);
update_otg2(isp, isp_bstat);
#endif
b_peripheral(isp);
} else if (!(isp_stat & (INTR_VBUS_VLD|INTR_SESS_VLD)))
isp_bstat |= OTG_B_SESS_END;
break;
case OTG_STATE_A_WAIT_VFALL:
break;
default:
pr_debug("otg: unsupported b-device %s\n",
state_name(isp));
break;
}
}
if (state != isp->otg.state)
pr_debug(" isp, %s -> %s\n",
state_string(state), state_name(isp));
#ifdef CONFIG_USB_OTG
/* update the OTG controller state to match the isp1301; may
* trigger OPRT_CHG irqs for changes going to the isp1301.
*/
update_otg1(isp, isp_stat);
update_otg2(isp, isp_bstat);
check_state(isp, __func__);
#endif
dump_regs(isp, "isp1301->otg");
}
