// Single-Ended 10bit, highbyte aligned.
// 3.85 V -> adval=192, adc_l = 128 -> 3 Red, 8 Green, 5 blue pulses.
static void blink_voltage(uint8_t adval, uint8_t adc_l)
{
set_led(L_WH1, 0xff); set_led(L_YL1, 0xff);
_delay_ms(200.0);
_delay_ms(200.0);
while (adval >= 50)
{
adval -= 50;
blink_once(L_RD2, 25); // 2Hz
}
adval = (adval<<1)+((adc_l & 0x80)?1:0);
led_off(L_WH1); led_off(L_YL1);
_delay_ms(200.0);
set_led(L_WH1, 0xff); set_led(L_YL1, 0xff);
_delay_ms(200.0);
while (adval >= 10)
{
adval -=10;
blink_once(L_GN1, 17); // 3Hz
}
led_off(L_WH1); led_off(L_YL1);
_delay_ms(200.0);
set_led(L_WH1, 0xff); set_led(L_YL1, 0xff);
_delay_ms(200.0);
while (adval-- > 0)
{
blink_once(L_BL2, 12); // 4hz
}
led_off(L_WH1); led_off(L_YL1);
_delay_ms(200.0);
}
int main(void)
{
bool cmd_ok = false;
wdt_enable(WDTO_8S);
// ADC enable; prescaler: 128 (156 KHz @ 20MHz)
ADCSRA |= (_BV(ADEN) | _BV(ADPS2) | _BV(ADPS1) | _BV(ADPS0));
DDRC |= _BV(DDC0); // LED:OUTPUT
// NLOCK: locked
DDRC |= _BV(DDC2); // OUTPUT
PORTC &= ~_BV(PORTC2); // LOW
#ifdef DEBUG
int m = DEBUG_CMD_DELAY; // ms
fdevopen(&serial_putc, 0); // open the stdout and stderr streams
#endif
sys_serial.begin(57600);
IF_DEBUG(printf_P(PSTR("BOOT\r\n")));
// initiate a sync with the daemon after boot
// there is a 1:65536 chance that sync will not be lost
// the daemon will initialize the device by the command
cmd.set(CMD_COMMON, COMMON_RESET, 0, 0);
common_device.confirm_boot(&cmd);
//cmd.reset(); // look to the SerialCommand::read
sys_log.begin();
SPI.begin();
if (radio.begin()) {
network.begin(RF24_CHANEL, rx_node);
nrf_device.setup(&network);
}
while(true)
{
wdt_reset();
// CMD_NRF_FORWARD
if (nrf_device.read(&cmd)) {
if (!nrf_device.run(&cmd)) cmd.send_header(-1);
//cmd.reset();
}
// CMD_RNG_SEND
for (int i = 0; i < WDT_BITS_PER_CYCLE; i++) {
if (rng_device.read(&cmd)) {
if (!rng_device.run(&cmd)) cmd.send_header(-1);
//cmd.reset();
}
}
// watchdog trigger
wdt_device.update();
#ifdef DEBUG
if (--m <= 0) {
m = DEBUG_CMD_DELAY;
//cmd.set(CMD_COMMON, 1, 1460792071, 0); // look to the SerialCommand::read
//sys_log.write(sys_time.now(), LOG_BOOT);
}
//_delay_ms(1);
#endif
// serial commands
if (cmd.read()) {
#ifdef DEBUG
blink_once();
#endif
cmd_ok = false;
switch (cmd.get_type()) {
case CMD_COMMON:
cmd_ok = common_device.run(&cmd);
break;
case CMD_WDT:
cmd_ok = wdt_device.run(&cmd);
break;
case CMD_RNG:
cmd_ok = rng_device.run(&cmd);
break;
case CMD_NRF:
cmd_ok = nrf_device.run(&cmd);
break;
default:
break;
}
if (!cmd_ok) cmd.send_header(-1);
//cmd.reset();
}
} // while(true)
sys_serial.end();
return 0;
} // main
void blink(uint16_t period_ms, uint16_t count)
{
uint16_t n = count;
while (n-- || count == 0)
blink_once(period_ms);
}
