static int e1000_set_settings(struct net_device *netdev,
struct ethtool_cmd *ecmd)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
/*
* When SoL/IDER sessions are active, autoneg/speed/duplex
* cannot be changed
*/
if (e1000_check_reset_block(hw)) {
e_err("Cannot change link characteristics when SoL/IDER is "
"active.\n");
return -EINVAL;
}
while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
msleep(1);
if (ecmd->autoneg == AUTONEG_ENABLE) {
hw->mac.autoneg = 1;
if (hw->phy.media_type == e1000_media_type_fiber)
hw->phy.autoneg_advertised = ADVERTISED_1000baseT_Full |
ADVERTISED_FIBRE |
ADVERTISED_Autoneg;
else
hw->phy.autoneg_advertised = ecmd->advertising |
ADVERTISED_TP |
ADVERTISED_Autoneg;
ecmd->advertising = hw->phy.autoneg_advertised;
if (adapter->fc_autoneg)
hw->fc.requested_mode = e1000_fc_default;
} else {
if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) {
clear_bit(__E1000_RESETTING, &adapter->state);
return -EINVAL;
}
}
/* reset the link */
if (netif_running(adapter->netdev)) {
e1000e_down(adapter);
e1000e_up(adapter);
} else {
e1000e_reset(adapter);
}
clear_bit(__E1000_RESETTING, &adapter->state);
return 0;
}
/**
* e1000_probe - Initial configuration of e1000 NIC
*
* @v pci PCI device
* @v id PCI IDs
*
* @ret rc Return status code
**/
int e1000_probe ( struct pci_device *pdev )
{
int i, err;
struct net_device *netdev;
struct e1000_adapter *adapter;
unsigned long mmio_start, mmio_len;
DBG ( "e1000_probe\n" );
err = -ENOMEM;
/* Allocate net device ( also allocates memory for netdev->priv
and makes netdev-priv point to it ) */
netdev = alloc_etherdev ( sizeof ( struct e1000_adapter ) );
if ( ! netdev )
goto err_alloc_etherdev;
/* Associate e1000-specific network operations operations with
* generic network device layer */
netdev_init ( netdev, &e1000_operations );
/* Associate this network device with given PCI device */
pci_set_drvdata ( pdev, netdev );
netdev->dev = &pdev->dev;
/* Initialize driver private storage */
adapter = netdev_priv ( netdev );
memset ( adapter, 0, ( sizeof ( *adapter ) ) );
adapter->pdev = pdev;
adapter->ioaddr = pdev->ioaddr;
adapter->hw.io_base = pdev->ioaddr;
adapter->irqno = pdev->irq;
adapter->netdev = netdev;
adapter->hw.back = adapter;
adapter->tx_ring_size = sizeof ( *adapter->tx_base ) * NUM_TX_DESC;
adapter->rx_ring_size = sizeof ( *adapter->rx_base ) * NUM_RX_DESC;
mmio_start = pci_bar_start ( pdev, PCI_BASE_ADDRESS_0 );
mmio_len = pci_bar_size ( pdev, PCI_BASE_ADDRESS_0 );
DBG ( "mmio_start: %#08lx\n", mmio_start );
DBG ( "mmio_len: %#08lx\n", mmio_len );
/* Fix up PCI device */
adjust_pci_device ( pdev );
err = -EIO;
adapter->hw.hw_addr = ioremap ( mmio_start, mmio_len );
DBG ( "adapter->hw.hw_addr: %p\n", adapter->hw.hw_addr );
if ( ! adapter->hw.hw_addr )
goto err_ioremap;
/* Hardware features, flags and workarounds */
if (adapter->hw.mac.type >= e1000_82540) {
adapter->flags |= E1000_FLAG_HAS_SMBUS;
adapter->flags |= E1000_FLAG_HAS_INTR_MODERATION;
}
if (adapter->hw.mac.type == e1000_82543)
adapter->flags |= E1000_FLAG_BAD_TX_CARRIER_STATS_FD;
adapter->hw.phy.autoneg_wait_to_complete = true;
adapter->hw.mac.adaptive_ifs = true;
/* setup the private structure */
if ( ( err = e1000_sw_init ( adapter ) ) )
goto err_sw_init;
if ((err = e1000_init_mac_params(&adapter->hw)))
goto err_hw_init;
if ((err = e1000_init_nvm_params(&adapter->hw)))
goto err_hw_init;
/* Force auto-negotiated speed and duplex */
adapter->hw.mac.autoneg = 1;
if ((err = e1000_init_phy_params(&adapter->hw)))
goto err_hw_init;
DBG ( "adapter->hw.mac.type: %#08x\n", adapter->hw.mac.type );
/* before reading the EEPROM, reset the controller to
* put the device in a known good starting state
*/
err = e1000_reset_hw ( &adapter->hw );
if ( err < 0 ) {
DBG ( "Hardware Initialization Failed\n" );
goto err_reset;
}
/* make sure the NVM is good */
if ( e1000_validate_nvm_checksum(&adapter->hw) < 0 ) {
DBG ( "The NVM Checksum Is Not Valid\n" );
err = -EIO;
goto err_eeprom;
}
/* copy the MAC address out of the EEPROM */
if ( e1000_read_mac_addr ( &adapter->hw ) )
DBG ( "EEPROM Read Error\n" );
memcpy ( netdev->hw_addr, adapter->hw.mac.perm_addr, ETH_ALEN );
/* reset the hardware with the new settings */
e1000_reset ( adapter );
if ( ( err = register_netdev ( netdev ) ) != 0)
goto err_register;
/* Mark as link up; we don't yet handle link state */
netdev_link_up ( netdev );
for (i = 0; i < 6; i++)
DBG ("%02x%s", netdev->ll_addr[i], i == 5 ? "\n" : ":");
DBG ( "e1000_probe succeeded!\n" );
/* No errors, return success */
return 0;
/* Error return paths */
err_reset:
err_register:
err_hw_init:
err_eeprom:
if (!e1000_check_reset_block(&adapter->hw))
e1000_phy_hw_reset(&adapter->hw);
if (adapter->hw.flash_address)
iounmap(adapter->hw.flash_address);
err_sw_init:
iounmap ( adapter->hw.hw_addr );
err_ioremap:
netdev_put ( netdev );
err_alloc_etherdev:
return err;
}
