コード例 #1
0
ファイル: main.c プロジェクト: Darthsternie/PSP
int main() 
{

   	pspDebugScreenInit();
	int devkit = sceKernelDevkitVersion(),
	cursor = 0;
	
		if(devkit != 0x06060010)
		Exit("This program supports only 6.60!");

    printf("USB Mod Flasher\n\n");    
	setcolor(RED);
	printf("This Mod is only for the TN-V8 eCFW for the PS Vita!");
	setcolor(WHITE);
	printf("\n\n\n\n\n\n\n\n\n\n\n\nCredits:\nXMB Mod by The Z\nInstaller Port by KanadeEngel\n\nSpecial Thanks to:\nfrostegater");

	while(1)
	{
		if(cursor > 2)
			cursor = 0;
		else if(cursor < 0)
			cursor = 2;

		if(cursor == 0) setbcolor(GRAY);
		printfc(3, 4, " Install XMB Mod.                       ");
		setbcolor(BLACK);
		if(cursor == 1) setbcolor(GRAY);
		printfc(3, 5, " Restore Original Files.                ");
		setbcolor(BLACK);
		if(cursor == 2) setbcolor(GRAY);
		printfc(3, 6, " Exit.                                  ");
		setbcolor(BLACK);

		int i;
		for(i = 0; i < 4; i++)
			printfc(1, 4 + i, " ");

		setcolor(BLUE);
		printfc(1, 4 + cursor, ">");

		unsigned int Buttons = wait_press(PSP_CTRL_CROSS | PSP_CTRL_UP | PSP_CTRL_DOWN);
		wait_release(PSP_CTRL_CROSS | PSP_CTRL_UP | PSP_CTRL_DOWN);

		SceCtrlData pad;
		sceCtrlReadBufferPositive(&pad, 1);

		if(Buttons & PSP_CTRL_CROSS)
		{
			if(cursor != 2)
			{
				setc(0, 9);
				if(assign_flash_zero() < 0)
					Exit("\n Error in 'flash0:/' assign.");
	

					{
						if(cursor == 0)//Install Mod Module
						{
							flash_file("flash0:/vsh/resource/topmenu_icon.rco", _660_install_X_icon, size__660_install_X_icon);
						}
	                    else if(cursor == 1)//Restore Original Module
							flash_file("flash0:/vsh/resource/topmenu_icon.rco", _660_original_X_icon, size__660_original_X_icon);
						}
					}
			else
				Exit("");

			break;
		}
		else if(Buttons & PSP_CTRL_UP)
			cursor--;
		else if(Buttons & PSP_CTRL_DOWN)
			cursor++;
	}

	Exit("Done.");
   sceKernelExitGame();
	return 0;
}
コード例 #2
0
ファイル: main.c プロジェクト: 69yuan/sd2snes
int main(void) {
  SNES_CIC_PAIR_REG->FIODIR = BV(SNES_CIC_PAIR_BIT);
  BITBAND(SNES_CIC_PAIR_REG->FIOSET, SNES_CIC_PAIR_BIT) = 1;
/*  LPC_GPIO2->FIODIR = BV(0) | BV(1) | BV(2); */
//  LPC_GPIO0->FIODIR = BV(16);

 /* connect UART3 on P0[25:26] + SSP0 on P0[15:18] + MAT3.0 on P0[10] */
  LPC_PINCON->PINSEL1 = BV(18) | BV(19) | BV(20) | BV(21) /* UART3 */
                      | BV(3) | BV(5);                    /* SSP0 (FPGA) except SS */
  LPC_PINCON->PINSEL0 = BV(31);                            /* SSP0 */
/*                      | BV(13) | BV(15) | BV(17) | BV(19)  SSP1 (SD) */

 /* pull-down CIC data lines */
  LPC_PINCON->PINMODE0 = BV(0) | BV(1) | BV(2) | BV(3);

  clock_disconnect();
  power_init();
  timer_init();
  DBG_UART uart_init();
  led_init();
  readled(0);
  rdyled(1);
  writeled(0);
 /* do this last because the peripheral init()s change PCLK dividers */
  clock_init();
//  LPC_PINCON->PINSEL0 |= BV(20) | BV(21);                  /* MAT3.0 (FPGA clock) */
  sdn_init();
  DBG_BL printf("chksum=%08lx\n", *(uint32_t*)28);
  DBG_BL printf("\n\nsd2snes mk.2 bootloader\nver.: " VER "\ncpu clock: %ld Hz\n", CONFIG_CPU_FREQUENCY);
DBG_BL printf("PCONP=%lx\n", LPC_SC->PCONP);
/* setup timer (fpga clk) */
  LPC_TIM3->CTCR=0;
  LPC_TIM3->EMR=EMC0TOGGLE;
  LPC_TIM3->MCR=MR0R;
  LPC_TIM3->MR0=1;
  LPC_TIM3->TCR=1;
  NVIC->ICER[0] = 0xffffffff;
  NVIC->ICER[1] = 0xffffffff;
  FLASH_RES res = flash_file((uint8_t*)"/sd2snes/firmware.img");
  if(res == ERR_FLASHPREP || res == ERR_FLASHERASE || res == ERR_FLASH) {
    rdyled(0);
    writeled(1);
  }
  if(res == ERR_FILEHD || res == ERR_FILECHK) {
    rdyled(0);
    readled(1);
  }
  DBG_BL printf("flash result = %d\n", res);
  if(res != ERR_OK) {
    if((res = check_flash()) != ERR_OK) {
      DBG_BL printf("check_flash() failed with error %d, not booting.\n", res);
      while(1) {
        toggle_rdy_led();
        delay_ms(500);
      }
    }
  }
  NVIC_DisableIRQ(RIT_IRQn);
  NVIC_DisableIRQ(UART_IRQ);

  SCB->VTOR=FW_START+0x00000100;
  chain = (void*)(*((uint32_t*)(FW_START+0x00000104)));
  uart_putc("0123456789abcdef"[((uint32_t)chain>>28)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>24)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>20)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>16)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>12)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>8)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain>>4)&15]);
  uart_putc("0123456789abcdef"[((uint32_t)chain)&15]);
  uart_putc('\n');
  chain();
  while(1);
}