コード例 #1
0
ファイル: pic18f458_i2c_setup.c プロジェクト: gntoni/projectM
/*
 * MAIN
 */
int main(int argc, char** argv) {

    // RA1 as DO
    LATA = 0;
    ADCON1 = 0x06;
    TRISA1 = 0;
    LATA1 = 1;

    // I2C configuration
    i2c_setup();

    unsigned char w;
    for(w=0;w<20;w++)
        I2C_Recv[w]=0;

    unsigned int temps = 25;
    unsigned char temp, length=0;
    while(1){
        LATA1 = ~LATA1;
        Delay10KTCYx(temps);
        check_interruptions();
        if (DataRdyI2C()==1) {
            temps += 25;
            temp = ReadI2C();
            //********************* Data reception from master by slave *********************
            do {
                while(DataRdyI2C()==0);        // WAIT UNTILL THE DATA IS TRANSMITTED FROM master
                I2C_Recv[length++]=getcI2C();  // save byte received
            }
            while(length!=20);
        }
    }

    //******************** write sequence from slave *******************************
    while(SSPSTATbits.S!=1); //wait untill STOP CONDITION

    //********************* Read the address sent by master from buffer **************
    while(DataRdyI2C()==0); //WAIT UNTILL THE DATA IS TRANSMITTED FROM master
    temp = ReadI2C();

    //********************* Slave transmission ************************************
    if(SSPSTAT & 0x04) //check if master is ready for reception
        while(putsI2C(I2C_Send));			// send the data to master

    //-------------TERMINATE COMMUNICATION FROM MASTER SIDE---------------
    CloseI2C(); //close I2C module
    
    while(1) {
        LATA1 = ~LATA1;
        Delay10KTCYx(100);
    }; //End of program


    return (EXIT_SUCCESS);
}
コード例 #2
0
ファイル: I2CEEPROM.c プロジェクト: Cougar/HomeAutomation
/*********************************************************************
 * Function:        XEE_RESULT XEERead(void)
 *
 * PreCondition:    XEEInit() && XEEBeginRead() are already called.
 *
 * Input:           None
 *
 * Output:          XEE_SUCCESS if successful
 *                  other value if failed.
 *
 * Side Effects:    None
 *
 * Overview:        Reads next byte from EEPROM; internal address
 *                  is incremented by one.
 *
 * Note:            This function does not release I2C bus.
 *                  User must call XEEEndRead() when read is not longer
 *                  needed; I2C bus will released after XEEEndRead()
 *                  is called.
 ********************************************************************/
unsigned char XEERead(void)
{
    getcI2C();
    while( EEPROM_SPICON2bits.RCEN );  // check that receive sequence is over.

    EEPROM_SPICON2bits.ACKDT = 0;      // Set ack bit
    EEPROM_SPICON2bits.ACKEN = 1;
    while( EEPROM_SPICON2bits.ACKEN );

    return EEPROM_SSPBUF;
}
コード例 #3
0
ファイル: I2CEEPROM.c プロジェクト: Cougar/HomeAutomation
/*********************************************************************
 * Function:        XEE_RESULT XEEEndRead(void)
 *
 * PreCondition:    XEEInit() && XEEBeginRead() are already called.
 *
 * Input:           None
 *
 * Output:          XEE_SUCCESS if successful
 *                  other value if failed.
 *
 * Side Effects:    None
 *
 * Overview:        Ends sequential read cycle.
 *
 * Note:            This function ends seuential cycle that was in
 *                  progress.  It releases I2C bus.
 ********************************************************************/
XEE_RESULT XEEEndRead(void)
{
    getcI2C();
    while( EEPROM_SPICON2bits.RCEN );  // check that receive sequence is over.

    NotAckI2C();
    while( EEPROM_SPICON2bits.ACKEN );

    StopI2C();
    while( EEPROM_SPICON2bits.PEN );

    return XEE_SUCCESS;
}