void hsi_softreset_driver(struct hsi_dev *hsi_ctrl)
{
struct platform_device *pd = to_platform_device(hsi_ctrl->dev);
struct hsi_platform_data *pdata = pd->dev.platform_data;
struct hsi_port *hsi_p;
unsigned int port;
u32 revision;
/* HSI port reset */
for (port = 0; port < hsi_ctrl->max_p; port++) {
hsi_p = &hsi_ctrl->hsi_port[port];
hsi_p->counters_on = 1;
hsi_p->reg_counters = pdata->ctx->pctx[port].hsr.counters;
hsi_port_channels_reset(&hsi_ctrl->hsi_port[port]);
}
hsi_set_pm_default(hsi_ctrl);
/* Re-Configure HSI ports */
hsi_set_ports_default(hsi_ctrl, pd);
/* Gather info from registers for the driver.(REVISION) */
revision = hsi_inl(hsi_ctrl->base, HSI_SYS_REVISION_REG);
if (hsi_driver_device_is_hsi(pd))
dev_info(hsi_ctrl->dev, "HSI Hardware REVISION 0x%x\n",
revision);
else
dev_info(hsi_ctrl->dev, "SSI Hardware REVISION %d.%d\n",
(revision & HSI_SSI_REV_MAJOR) >> 4,
(revision & HSI_SSI_REV_MINOR));
}
/**
* hsi_ioctl - HSI I/O control
* @dev - hsi device channel reference to apply the I/O control
* (or port associated to it)
* @command - HSI I/O control command
* @arg - parameter associated to the control command. NULL, if no parameter.
*
* Return 0 on success, a negative value on failure.
*
*/
int hsi_ioctl(struct hsi_device *dev, unsigned int command, void *arg)
{
struct hsi_channel *ch;
struct hsi_dev *hsi_ctrl;
struct hsi_port *pport;
void __iomem *base;
unsigned int port, channel;
u32 acwake;
int err = 0;
int fifo = 0;
u8 ret;
struct hsi_platform_data *pdata;
if (unlikely((!dev) ||
(!dev->ch) ||
(!dev->ch->hsi_port) ||
(!dev->ch->hsi_port->hsi_controller)) ||
(!(dev->ch->flags & HSI_CH_OPEN))) {
pr_err(LOG_NAME "HSI IOCTL Invalid parameter\n");
return -EINVAL;
}
ch = dev->ch;
pport = ch->hsi_port;
hsi_ctrl = ch->hsi_port->hsi_controller;
port = ch->hsi_port->port_number;
channel = ch->channel_number;
base = hsi_ctrl->base;
dev_dbg(hsi_ctrl->dev, "IOCTL: ch %d, command %d\n", channel, command);
spin_lock_bh(&hsi_ctrl->lock);
hsi_clocks_enable_channel(hsi_ctrl->dev, channel, __func__);
switch (command) {
case HSI_IOCTL_ACWAKE_UP:
/* Wake up request to Modem (typically OMAP initiated) */
/* Symetrical disable will be done in HSI_IOCTL_ACWAKE_DOWN */
if (ch->flags & HSI_CH_ACWAKE) {
dev_dbg(hsi_ctrl->dev, "Duplicate ACWAKE UP\n");
err = -EPERM;
goto out;
}
ch->flags |= HSI_CH_ACWAKE;
pport->acwake_status |= BIT(channel);
/* We only claim once the wake line per channel */
acwake = hsi_inl(base, HSI_SYS_WAKE_REG(port));
if (!(acwake & HSI_WAKE(channel))) {
hsi_outl(HSI_SET_WAKE(channel), base,
HSI_SYS_SET_WAKE_REG(port));
}
goto out;
break;
case HSI_IOCTL_ACWAKE_DOWN:
/* Low power request initiation (OMAP initiated, typically */
/* following inactivity timeout) */
/* ACPU HSI block shall still be capable of receiving */
if (!(ch->flags & HSI_CH_ACWAKE)) {
dev_dbg(hsi_ctrl->dev, "Duplicate ACWAKE DOWN\n");
err = -EPERM;
goto out;
}
acwake = hsi_inl(base, HSI_SYS_WAKE_REG(port));
if (unlikely(pport->acwake_status !=
(acwake & HSI_WAKE_MASK))) {
dev_warn(hsi_ctrl->dev,
"ACWAKE shadow register mismatch"
" acwake_status: 0x%x, HSI_SYS_WAKE_REG: 0x%x",
pport->acwake_status, acwake);
pport->acwake_status = acwake & HSI_WAKE_MASK;
}
/* SSI_TODO: add safety check for SSI also */
ch->flags &= ~HSI_CH_ACWAKE;
pport->acwake_status &= ~BIT(channel);
/* Release the wake line per channel */
if ((acwake & HSI_WAKE(channel))) {
hsi_outl(HSI_CLEAR_WAKE(channel), base,
HSI_SYS_CLEAR_WAKE_REG(port));
}
goto out;
break;
case HSI_IOCTL_SEND_BREAK:
hsi_outl(1, base, HSI_HST_BREAK_REG(port));
/*HSI_TODO : need to deactivate clock after BREAK frames sent*/
/*Use interrupt ? (if TX BREAK INT exists)*/
break;
case HSI_IOCTL_GET_ACWAKE:
if (!arg) {
err = -EINVAL;
goto out;
}
*(u32 *)arg = hsi_inl(base, HSI_SYS_WAKE_REG(port));
break;
case HSI_IOCTL_FLUSH_RX:
ret = hsi_hsr_fifo_flush_channel(hsi_ctrl, port, channel);
if (arg)
*(size_t *)arg = ret;
/* Ack the RX Int */
hsi_outl_and(~HSI_HSR_DATAAVAILABLE(channel), base,
HSI_SYS_MPU_STATUS_CH_REG(port, pport->n_irq,
channel));
break;
case HSI_IOCTL_FLUSH_TX:
ret = hsi_hst_fifo_flush_channel(hsi_ctrl, port, channel);
if (arg)
*(size_t *)arg = ret;
/* Ack the TX Int */
hsi_outl_and(~HSI_HST_DATAACCEPT(channel), base,
HSI_SYS_MPU_STATUS_CH_REG(port, pport->n_irq,
channel));
break;
case HSI_IOCTL_GET_CAWAKE:
if (!arg) {
err = -EINVAL;
goto out;
}
err = hsi_get_cawake(dev->ch->hsi_port);
if (err < 0) {
err = -ENODEV;
goto out;
}
*(u32 *)arg = err;
break;
case HSI_IOCTL_SET_RX:
if (!arg) {
err = -EINVAL;
goto out;
}
err = hsi_set_rx(dev->ch->hsi_port, (struct hsr_ctx *)arg);
break;
case HSI_IOCTL_GET_RX:
if (!arg) {
err = -EINVAL;
goto out;
}
hsi_get_rx(dev->ch->hsi_port, (struct hsr_ctx *)arg);
break;
case HSI_IOCTL_SET_TX:
if (!arg) {
err = -EINVAL;
goto out;
}
err = hsi_set_tx(dev->ch->hsi_port, (struct hst_ctx *)arg);
break;
case HSI_IOCTL_GET_TX:
if (!arg) {
err = -EINVAL;
goto out;
}
hsi_get_tx(dev->ch->hsi_port, (struct hst_ctx *)arg);
break;
case HSI_IOCTL_SW_RESET:
dev_info(hsi_ctrl->dev, "SW Reset\n");
err = hsi_softreset(hsi_ctrl);
/* Reset HSI config to default */
hsi_softreset_driver(hsi_ctrl);
break;
case HSI_IOCTL_GET_FIFO_OCCUPANCY:
if (!arg) {
err = -EINVAL;
goto out;
}
fifo = hsi_fifo_get_id(hsi_ctrl, channel, port);
if (unlikely(fifo < 0)) {
dev_err(hsi_ctrl->dev, "No valid FIFO id found for "
"channel %d.\n", channel);
err = -EFAULT;
goto out;
}
*(size_t *)arg = hsi_get_rx_fifo_occupancy(hsi_ctrl, fifo);
break;
case HSI_IOCTL_SET_WAKE_RX_3WIRES_MODE:
dev_info(hsi_ctrl->dev,
"Entering RX wakeup in 3 wires mode (no CAWAKE)\n");
pport->wake_rx_3_wires_mode = 1;
/* HSI-C1BUG00085: ixxx: HSI wakeup issue in 3 wires mode
* HSI will NOT generate the Swakeup for 2nd frame if it entered
* IDLE after 1st received frame */
if (is_hsi_errata(hsi_ctrl, HSI_ERRATUM_ixxx_3WIRES_NO_SWAKEUP))
if (hsi_driver_device_is_hsi(to_platform_device
(hsi_ctrl->dev)))
hsi_set_pm_force_hsi_on(hsi_ctrl);
/* When WAKE is not available, ACREADY must be set to 1 at
* reset else remote will never have a chance to transmit. */
hsi_outl_or(HSI_SET_WAKE_3_WIRES | HSI_SET_WAKE_READY_LVL_1,
base, HSI_SYS_SET_WAKE_REG(port));
hsi_driver_disable_interrupt(pport, HSI_CAWAKEDETECTED);
break;
case HSI_IOCTL_SET_WAKE_RX_4WIRES_MODE:
dev_info(hsi_ctrl->dev, "Entering RX wakeup in 4 wires mode\n");
pport->wake_rx_3_wires_mode = 0;
/* HSI-C1BUG00085: ixxx: HSI wakeup issue in 3 wires mode
* HSI will NOT generate the Swakeup for 2nd frame if it entered
* IDLE after 1st received frame */
if (is_hsi_errata(hsi_ctrl, HSI_ERRATUM_ixxx_3WIRES_NO_SWAKEUP))
if (hsi_driver_device_is_hsi(to_platform_device
(hsi_ctrl->dev)))
hsi_set_pm_default(hsi_ctrl);
hsi_driver_enable_interrupt(pport, HSI_CAWAKEDETECTED);
hsi_outl_and(HSI_SET_WAKE_3_WIRES_MASK, base,
HSI_SYS_SET_WAKE_REG(port));
break;
case HSI_IOCTL_SET_HI_SPEED:
if (!arg) {
err = -EINVAL;
goto out;
}
hsi_ctrl->hsi_fclk_req = *(unsigned int *)arg ?
HSI_FCLK_HI_SPEED : HSI_FCLK_LOW_SPEED;
if (hsi_ctrl->hsi_fclk_req == hsi_ctrl->hsi_fclk_current) {
dev_dbg(hsi_ctrl->dev, "HSI FClk already @%ldHz\n",
hsi_ctrl->hsi_fclk_current);
goto out;
}
if (hsi_is_controller_transfer_ongoing(hsi_ctrl)) {
err = -EBUSY;
goto out;
}
hsi_ctrl->clock_change_ongoing = true;
spin_unlock_bh(&hsi_ctrl->lock);
pdata = dev_get_platdata(hsi_ctrl->dev);
/* Set the HSI FCLK to requested value. */
err = pdata->device_scale(hsi_ctrl->dev, hsi_ctrl->dev,
hsi_ctrl->hsi_fclk_req);
if (err < 0) {
dev_err(hsi_ctrl->dev, "%s: Cannot set HSI FClk to"
" %ldHz, err %d\n", __func__,
hsi_ctrl->hsi_fclk_req, err);
} else {
dev_info(hsi_ctrl->dev, "HSI FClk changed from %ldHz to"
" %ldHz\n", hsi_ctrl->hsi_fclk_current,
hsi_ctrl->hsi_fclk_req);
hsi_ctrl->hsi_fclk_current = hsi_ctrl->hsi_fclk_req;
}
spin_lock_bh(&hsi_ctrl->lock);
hsi_ctrl->clock_change_ongoing = false;
break;
case HSI_IOCTL_GET_SPEED:
if (!arg) {
err = -EINVAL;
goto out;
}
*(unsigned long *)arg = hsi_ctrl->hsi_fclk_current;
break;
default:
err = -ENOIOCTLCMD;
break;
}
out:
/* All IOCTL end by disabling the clocks, except ACWAKE high. */
hsi_clocks_disable_channel(hsi_ctrl->dev, channel, __func__);
spin_unlock_bh(&hsi_ctrl->lock);
return err;
}
/* HSI Platform Device probing & hsi_device registration */
static int __init hsi_platform_device_probe(struct platform_device *pd)
{
struct hsi_platform_data *pdata = pd->dev.platform_data;
struct hsi_dev *hsi_ctrl;
u32 revision;
int err;
dev_dbg(&pd->dev, "HSI DRIVER : hsi_platform_device_probe\n");
dev_dbg(&pd->dev, "The platform device probed is an %s\n",
hsi_driver_device_is_hsi(pd) ? "HSI" : "SSI");
if (!pdata) {
pr_err(LOG_NAME "No platform_data found on hsi device\n");
return -ENXIO;
}
hsi_ctrl = kzalloc(sizeof(*hsi_ctrl), GFP_KERNEL);
if (hsi_ctrl == NULL) {
dev_err(&pd->dev, "Could not allocate memory for"
" struct hsi_dev\n");
return -ENOMEM;
}
platform_set_drvdata(pd, hsi_ctrl);
err = hsi_controller_init(hsi_ctrl, pd);
if (err < 0) {
dev_err(&pd->dev, "Could not initialize hsi controller:"
" %d\n", err);
goto rollback1;
}
pm_runtime_enable(hsi_ctrl->dev);
hsi_clocks_enable(hsi_ctrl->dev, __func__);
/* Non critical SW Reset */
err = hsi_softreset(hsi_ctrl);
if (err < 0)
goto rollback2;
hsi_set_pm_default(hsi_ctrl);
/* Configure HSI ports */
hsi_set_ports_default(hsi_ctrl, pd);
/* Gather info from registers for the driver.(REVISION) */
revision = hsi_inl(hsi_ctrl->base, HSI_SYS_REVISION_REG);
if (hsi_driver_device_is_hsi(pd))
dev_info(hsi_ctrl->dev, "HSI Hardware REVISION 0x%x\n",
revision);
else
dev_info(hsi_ctrl->dev, "SSI Hardware REVISION %d.%d\n",
(revision & HSI_SSI_REV_MAJOR) >> 4,
(revision & HSI_SSI_REV_MINOR));
err = hsi_debug_add_ctrl(hsi_ctrl);
if (err < 0) {
dev_err(&pd->dev,
"Could not add hsi controller to debugfs: %d\n", err);
goto rollback2;
}
err = register_hsi_devices(hsi_ctrl);
if (err < 0) {
dev_err(&pd->dev, "Could not register hsi_devices: %d\n", err);
goto rollback3;
}
/* From here no need for HSI HW access */
hsi_clocks_disable(hsi_ctrl->dev, __func__);
/* Allow HSI to wake up the platform */
device_init_wakeup(hsi_ctrl->dev, 1);
/* Set the HSI FCLK to default. */
err = omap_device_set_rate(hsi_ctrl->dev, hsi_ctrl->dev,
pdata->default_hsi_fclk);
if (err)
dev_err(&pd->dev, "Cannot set HSI FClk to default value: %ld\n",
pdata->default_hsi_fclk);
return err;
rollback3:
hsi_debug_remove_ctrl(hsi_ctrl);
rollback2:
hsi_controller_exit(hsi_ctrl);
/* From here no need for HSI HW access */
hsi_clocks_disable(hsi_ctrl->dev, __func__);
rollback1:
kfree(hsi_ctrl);
return err;
}
