/* The port lock is not held. */
static void
ip22zilog_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
unsigned long flags;
int baud, brg;
baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
spin_lock_irqsave(&up->port.lock, flags);
brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
else
up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
uart_update_timeout(port, termios->c_cflag, baud);
spin_unlock_irqrestore(&up->port.lock, flags);
}
/* The port lock is held and interrupts are disabled. */
static void ip22zilog_stop_rx(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
if (ZS_IS_CONS(up))
return;
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable all RX interrupts. */
up->curregs[R1] &= ~RxINT_MASK;
ip22zilog_maybe_update_regs(up, channel);
}
static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
{
struct zilog_channel *channel;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
up->prev_status = readb(&channel->control);
/* Enable receiver and transmitter. */
up->curregs[R3] |= RxENAB;
up->curregs[R5] |= TxENAB;
up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
ip22zilog_maybe_update_regs(up, channel);
}
static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
{
struct zilog_channel *channel;
channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
__ip22zilog_reset(up);
__load_zsregs(channel, up->curregs);
/* set master interrupt enable */
write_zsreg(channel, R9, up->curregs[R9]);
up->prev_status = readb(&channel->control);
/* Enable receiver and transmitter. */
up->curregs[R3] |= RxENAB;
up->curregs[R5] |= TxENAB;
up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
ip22zilog_maybe_update_regs(up, channel);
}
/*
* The test for ZS_IS_CONS is explained by the following e-mail:
*****
* From: Russell King <*****@*****.**>
* Date: Sun, 8 Dec 2002 10:18:38 +0000
*
* On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
* > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
* > and I noticed that something is not right with reference
* > counting in this case. It seems that when the console
* > is open by kernel initially, this is not accounted
* > as an open, and uart_startup is not called.
*
* That is correct. We are unable to call uart_startup when the serial
* console is initialised because it may need to allocate memory (as
* request_irq does) and the memory allocators may not have been
* initialised.
*
* 1. initialise the port into a state where it can send characters in the
* console write method.
*
* 2. don't do the actual hardware shutdown in your shutdown() method (but
* do the normal software shutdown - ie, free irqs etc)
*****
*/
static void ip22zilog_shutdown(struct uart_port *port)
{
struct uart_ip22zilog_port *up = UART_ZILOG(port);
struct zilog_channel *channel;
unsigned long flags;
if (ZS_IS_CONS(up))
return;
spin_lock_irqsave(&port->lock, flags);
channel = ZILOG_CHANNEL_FROM_PORT(port);
/* Disable receiver and transmitter. */
up->curregs[R3] &= ~RxENAB;
up->curregs[R5] &= ~TxENAB;
/* Disable all interrupts and BRK assertion. */
up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
up->curregs[R5] &= ~SND_BRK;
ip22zilog_maybe_update_regs(up, channel);
spin_unlock_irqrestore(&port->lock, flags);
}
