int up_prioritize_irq(int irq, int priority)
{
uint32_t regaddr;
uint32_t regval;
int shift;
DEBUGASSERT(irq >= LPC43_IRQ_MEMFAULT && irq < NR_IRQS &&
(unsigned)priority <= NVIC_SYSH_PRIORITY_MIN);
if (irq < LPC43_IRQ_EXTINT)
{
/* NVIC_SYSH_PRIORITY() maps {0..15} to one of three priority
* registers (0-3 are invalid)
*/
regaddr = NVIC_SYSH_PRIORITY(irq);
irq -= 4;
}
else
{
/* NVIC_IRQ_PRIORITY() maps {0..} to one of many priority registers */
irq -= LPC43_IRQ_EXTINT;
regaddr = NVIC_IRQ_PRIORITY(irq);
}
regval = getreg32(regaddr);
shift = ((irq & 3) << 3);
regval &= ~(0xff << shift);
regval |= (priority << shift);
putreg32(regval, regaddr);
lpc43_dumpnvic("prioritize", irq);
return OK;
}
void up_enable_irq(int irq)
{
uintptr_t regaddr;
uint32_t regval;
uint32_t bit;
if (lpc43_irqinfo(irq, ®addr, &bit, NVIC_ENA_OFFSET) == 0)
{
/* Modify the appropriate bit in the register to enable the interrupt.
* For normal interrupts, we need to set the bit in the associated
* Interrupt Set Enable register. For other exceptions, we need to
* set the bit in the System Handler Control and State Register.
*/
if (irq >= LPC43_IRQ_EXTINT)
{
putreg32(bit, regaddr);
}
else
{
regval = getreg32(regaddr);
regval |= bit;
putreg32(regval, regaddr);
}
}
lpc43_dumpnvic("enable", irq);
}
void up_enable_irq(int irq)
{
uintptr_t regaddr;
uint32_t regval;
uint32_t bit;
if (lpc43_irqinfo(irq, ®addr, &bit, NVIC_ENA_OFFSET) == 0)
{
/* Modify the appropriate bit in the register to enable the interrupt.
* For normal interrupts, we need to set the bit in the associated
* Interrupt Set Enable register. For other exceptions, we need to
* set the bit in the System Handler Control and State Register.
*/
if (irq >= LPC43_IRQ_EXTINT)
{
putreg32(bit, regaddr);
}
else
{
regval = getreg32(regaddr);
regval |= bit;
putreg32(regval, regaddr);
}
}
#ifdef CONFIG_GPIO_IRQ
else if (irq >= LPC43_VALID_FIRST0L)
{
/* Maybe it is a (derived) GPIO IRQ */
lpc43_gpioint_enable(irq);
}
#endif
lpc43_dumpnvic("enable", irq);
}
void up_irqinitialize(void)
{
uint32_t regaddr;
#ifdef CONFIG_DEBUG
uint32_t regval;
#endif
int num_priority_registers;
/* Disable all interrupts */
putreg32(0, NVIC_IRQ0_31_ENABLE);
putreg32(0, NVIC_IRQ32_63_ENABLE);
/* Make sure that we are using the correct vector table. The default
* vector address is 0x0000:0000 but if we are executing code that is
* positioned in SRAM or in external FLASH, then we may need to reset
* the interrupt vector so that it refers to the table in SRAM or in
* external FLASH.
*
* If CONFIG_ARCH_RAMVECTORS is defined, then we are using a RAM-based
* vector table that requires special initialization.
*/
#ifdef CONFIG_ARCH_RAMVECTORS
up_ramvec_initialize();
#else
putreg32((uint32_t)_vectors, NVIC_VECTAB);
#endif
/* Set all interrupts (and exceptions) to the default priority */
putreg32(DEFPRIORITY32, NVIC_SYSH4_7_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH8_11_PRIORITY);
putreg32(DEFPRIORITY32, NVIC_SYSH12_15_PRIORITY);
/* The NVIC ICTR register (bits 0-4) holds the number of of interrupt
* lines that the NVIC supports:
*
* 0 -> 32 interrupt lines, 8 priority registers
* 1 -> 64 " " " ", 16 priority registers
* 2 -> 96 " " " ", 32 priority registers
* ...
*/
num_priority_registers = (getreg32(NVIC_ICTR) + 1) * 8;
/* Now set all of the interrupt lines to the default priority */
regaddr = NVIC_IRQ0_3_PRIORITY;
while (num_priority_registers--)
{
putreg32(DEFPRIORITY32, regaddr);
regaddr += 4;
}
/* currents_regs is non-NULL only while processing an interrupt */
current_regs = NULL;
/* Attach the SVCall and Hard Fault exception handlers. The SVCall
* exception is used for performing context switches; The Hard Fault
* must also be caught because a SVCall may show up as a Hard Fault
* under certain conditions.
*/
irq_attach(LPC43_IRQ_SVCALL, up_svcall);
irq_attach(LPC43_IRQ_HARDFAULT, up_hardfault);
/* Set the priority of the SVCall interrupt */
#ifdef CONFIG_ARCH_IRQPRIO
/* up_prioritize_irq(LPC43_IRQ_PENDSV, NVIC_SYSH_PRIORITY_MIN); */
#endif
#ifdef CONFIG_ARMV7M_USEBASEPRI
lpc43_prioritize_syscall(NVIC_SYSH_SVCALL_PRIORITY);
#endif
/* If the MPU is enabled, then attach and enable the Memory Management
* Fault handler.
*/
#ifdef CONFIG_ARMV7M_MPU
irq_attach(LPC43_IRQ_MEMFAULT, up_memfault);
up_enable_irq(LPC43_IRQ_MEMFAULT);
#endif
/* Attach all other processor exceptions (except reset and sys tick) */
#ifdef CONFIG_DEBUG
irq_attach(LPC43_IRQ_NMI, lpc43_nmi);
#ifndef CONFIG_ARMV7M_MPU
irq_attach(LPC43_IRQ_MEMFAULT, up_memfault);
#endif
irq_attach(LPC43_IRQ_BUSFAULT, lpc43_busfault);
irq_attach(LPC43_IRQ_USAGEFAULT, lpc43_usagefault);
irq_attach(LPC43_IRQ_PENDSV, lpc43_pendsv);
irq_attach(LPC43_IRQ_DBGMONITOR, lpc43_dbgmonitor);
irq_attach(LPC43_IRQ_RESERVED, lpc43_reserved);
#endif
lpc43_dumpnvic("initial", LPC43M4_IRQ_NIRQS);
/* If a debugger is connected, try to prevent it from catching hardfaults.
* If CONFIG_ARMV7M_USEBASEPRI, no hardfaults are expected in normal
* operation.
*/
#if defined(CONFIG_DEBUG) && !defined(CONFIG_ARMV7M_USEBASEPRI)
regval = getreg32(NVIC_DEMCR);
regval &= ~NVIC_DEMCR_VCHARDERR;
putreg32(regval, NVIC_DEMCR);
#endif
/* And finally, enable interrupts */
#ifndef CONFIG_SUPPRESS_INTERRUPTS
irqenable();
#endif
}
