static unsigned int msm_AR600X_setup_power(bool on)
{
int rc = 0;
static bool init_done;
if (wlan_powered_up) {
pr_info("WLAN already powered up\n");
return 0;
}
if (unlikely(!init_done)) {
gpio_wlan_config();
rc = qrf6285_init_regs();
if (rc) {
pr_err("%s: qrf6285 init failed = %d\n", __func__, rc);
return rc;
} else {
init_done = true;
}
}
rc = wlan_switch_regulators(on);
if (rc) {
pr_err("%s: wlan_switch_regulators error = %d\n", __func__, rc);
goto out;
}
/* GPIO_WLAN_3V3_EN is only required for the QRD7627a */
if (machine_is_msm7627a_qrd1()) {
rc = gpio_tlmm_config(GPIO_CFG(GPIO_WLAN_3V3_EN, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s gpio_tlmm_config 119 failed,error = %d\n",
__func__, rc);
goto reg_disable;
}
gpio_set_value(GPIO_WLAN_3V3_EN, 1);
}
/*
* gpio_wlan_sys_rest_en is not from the GPIO expander for QRD7627a,
* EVB1.0 and QRD8625,so the below step is required for those devices.
*/
if (machine_is_msm7627a_qrd1() || machine_is_msm7627a_evb()
|| machine_is_msm8625_evb()
|| machine_is_msm8625_evt()
|| machine_is_msm7627a_qrd3()
|| machine_is_msm8625_qrd7()) {
rc = gpio_tlmm_config(GPIO_CFG(gpio_wlan_sys_rest_en, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s gpio_tlmm_config 119 failed,error = %d\n",
__func__, rc);
goto qrd_gpio_fail;
}
gpio_set_value(gpio_wlan_sys_rest_en, 1);
} else {
#if 1
rc = gpio_tlmm_config(GPIO_CFG(gpio_wlan_sys_rest_en, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s gpio_tlmm_config 119 failed,error = %d\n",
__func__, rc);
goto qrd_gpio_fail;
}
gpio_set_value(gpio_wlan_sys_rest_en, 1);
#else
rc = gpio_request(gpio_wlan_sys_rest_en, "WLAN_DEEP_SLEEP_N");
if (rc) {
pr_err("%s: WLAN sys_rest_en GPIO %d request failed %d\n",
__func__,
gpio_wlan_sys_rest_en, rc);
goto qrd_gpio_fail;
}
rc = setup_wlan_gpio(on);
if (rc) {
pr_err("%s: wlan_set_gpio = %d\n", __func__, rc);
goto gpio_fail;
}
#endif
}
/* Enable the A0 clock */
rc = setup_wlan_clock(on);
if (rc) {
pr_err("%s: setup_wlan_clock = %d\n", __func__, rc);
goto set_gpio_fail;
}
/* Configure A0 clock to be slave to WLAN_CLK_PWR_REQ */
rc = pmapp_clock_vote(id, PMAPP_CLOCK_ID_A0,
PMAPP_CLOCK_VOTE_PIN_CTRL);
if (rc) {
pr_err("%s: Configuring A0 to Pin controllable failed %d\n",
__func__, rc);
goto set_clock_fail;
}
pr_info("WLAN power-up success\n");
wlan_powered_up = true;
return 0;
set_clock_fail:
setup_wlan_clock(0);
set_gpio_fail:
setup_wlan_gpio(0);
//gpio_fail:
// gpio_free(gpio_wlan_sys_rest_en);
qrd_gpio_fail:
/* GPIO_WLAN_3V3_EN is only required for the QRD7627a */
if (machine_is_msm7627a_qrd1())
gpio_free(GPIO_WLAN_3V3_EN);
reg_disable:
wlan_switch_regulators(0);
out:
pr_info("WLAN power-up failed\n");
wlan_powered_up = false;
return rc;
}
void __init msm7627a_camera_init(void)
{
#ifndef CONFIG_MSM_CAMERA_V4L2
int rc;
#endif
pr_debug("msm7627a_camera_init Entered\n");
/* LCD and camera power (VREG & LDO) init */
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()) {
lcd_camera_power_init();
evb_camera_gpio_cfg();
}
#ifndef CONFIG_MSM_CAMERA_V4L2
if (machine_is_msm7627a_qrd1()) {
qrd1_camera_gpio_cfg();
platform_add_devices(camera_devices_qrd,
ARRAY_SIZE(camera_devices_qrd));
} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()) {
platform_add_devices(camera_devices_evb,
ARRAY_SIZE(camera_devices_evb));
} else if (machine_is_msm7627a_qrd3())
return;
else
platform_add_devices(camera_devices_msm,
ARRAY_SIZE(camera_devices_msm));
#endif
if (!machine_is_msm7627a_qrd1() || !machine_is_msm7627a_evb()
|| !machine_is_msm8625_evb())
register_i2c_devices();
#ifndef CONFIG_MSM_CAMERA_V4L2
rc = regulator_bulk_get(NULL, ARRAY_SIZE(regs_camera), regs_camera);
if (rc) {
pr_err("%s: could not get regulators: %d\n", __func__, rc);
return;
}
rc = regulator_bulk_set_voltage(ARRAY_SIZE(regs_camera), regs_camera);
if (rc) {
pr_err("%s: could not set voltages: %d\n", __func__, rc);
return;
}
#endif
#if defined(CONFIG_MSM_CAMERA_V4L2)
msm7x27a_init_cam();
#endif
#ifndef CONFIG_MSM_CAMERA_V4L2
if (machine_is_msm7627a_qrd1()) {
i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID,
i2c_camera_devices_qrd,
ARRAY_SIZE(i2c_camera_devices_qrd));
} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()) {
pr_debug("machine_is_msm7627a_evb i2c_register_board_info\n");
i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID,
i2c_camera_devices_evb,
ARRAY_SIZE(i2c_camera_devices_evb));
} else
#endif
pr_debug("i2c_register_board_info\n");
i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID,
i2c_camera_devices,
ARRAY_SIZE(i2c_camera_devices));
}
static unsigned int wlan_switch_regulators(int on)
{
int rc = 0, index = 0;
if (machine_is_msm7627a_qrd1())
index = 2;
for ( ; index < ARRAY_SIZE(vreg_info); index++) {
if (on) {
rc = regulator_set_voltage(vreg_info[index].reg,
vreg_info[index].level_min,
vreg_info[index].level_max);
if (rc) {
pr_err("%s:%s set voltage failed %d\n",
__func__, vreg_info[index].vreg_id, rc);
goto reg_disable;
}
rc = regulator_enable(vreg_info[index].reg);
if (rc) {
pr_err("%s:%s vreg enable failed %d\n",
__func__, vreg_info[index].vreg_id, rc);
goto reg_disable;
}
if (vreg_info[index].is_vreg_pin_controlled) {
rc = pmapp_vreg_lpm_pincntrl_vote(id,
vreg_info[index].pmapp_id,
PMAPP_CLOCK_ID_A0, 1);
if (rc) {
pr_err("%s:%s pincntrl failed %d\n",
__func__,
vreg_info[index].vreg_id, rc);
goto pin_cnt_fail;
}
}
} else {
if (vreg_info[index].is_vreg_pin_controlled) {
rc = pmapp_vreg_lpm_pincntrl_vote(id,
vreg_info[index].pmapp_id,
PMAPP_CLOCK_ID_A0, 0);
if (rc) {
pr_err("%s:%s pincntrl failed %d\n",
__func__,
vreg_info[index].vreg_id, rc);
goto pin_cnt_fail;
}
}
rc = regulator_disable(vreg_info[index].reg);
if (rc) {
pr_err("%s:%s vreg disable failed %d\n",
__func__,
vreg_info[index].vreg_id, rc);
goto reg_disable;
}
}
}
return 0;
pin_cnt_fail:
if (on)
regulator_disable(vreg_info[index].reg);
reg_disable:
if (!machine_is_msm7627a_qrd1()) {
while (index) {
if (on) {
index--;
regulator_disable(vreg_info[index].reg);
regulator_put(vreg_info[index].reg);
}
}
}
return rc;
}
static unsigned int msm_AR600X_shutdown_power(bool on)
{
int rc = 0;
if (!wlan_powered_up) {
pr_info("WLAN is not powered up, returning success\n");
return 0;
}
/* Disable the A0 clock */
rc = setup_wlan_clock(on);
if (rc) {
pr_err("%s: setup_wlan_clock = %d\n", __func__, rc);
goto set_gpio_fail;
}
/*
* gpio_wlan_sys_rest_en is not from the GPIO expander for QRD7627a,
* EVB1.0 and QRD8625,so the below step is required for those devices.
*/
if (machine_is_msm7627a_qrd1() || machine_is_msm7627a_evb()
|| machine_is_msm8625_evb()
|| machine_is_msm8625_evt()
|| machine_is_msm7627a_qrd3()
|| machine_is_msm8625_qrd7()) {
rc = gpio_tlmm_config(GPIO_CFG(gpio_wlan_sys_rest_en, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s gpio_tlmm_config 119 failed,error = %d\n",
__func__, rc);
goto gpio_fail;
}
gpio_set_value(gpio_wlan_sys_rest_en, 0);
} else {
rc = setup_wlan_gpio(on);
if (rc) {
pr_err("%s: setup_wlan_gpio = %d\n", __func__, rc);
goto set_gpio_fail;
}
gpio_free(gpio_wlan_sys_rest_en);
}
/* GPIO_WLAN_3V3_EN is only required for the QRD7627a */
if (machine_is_msm7627a_qrd1()) {
rc = gpio_tlmm_config(GPIO_CFG(GPIO_WLAN_3V3_EN, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s gpio_tlmm_config 119 failed,error = %d\n",
__func__, rc);
goto qrd_gpio_fail;
}
gpio_set_value(GPIO_WLAN_3V3_EN, 0);
}
rc = wlan_switch_regulators(on);
if (rc) {
pr_err("%s: wlan_switch_regulators error = %d\n",
__func__, rc);
goto reg_disable;
}
wlan_powered_up = false;
pr_info("WLAN power-down success\n");
return 0;
set_gpio_fail:
setup_wlan_gpio(0);
gpio_fail:
if (!(machine_is_msm7627a_qrd1() || machine_is_msm7627a_evb() ||
machine_is_msm8625_evb() || machine_is_msm8625_evt() ||
machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7() ||
machine_is_msm8625q_evbd() || machine_is_qrd_skud_prime()))
gpio_free(gpio_wlan_sys_rest_en);
qrd_gpio_fail:
/* GPIO_WLAN_3V3_EN is only required for the QRD7627a */
if (machine_is_msm7627a_qrd1())
gpio_free(GPIO_WLAN_3V3_EN);
reg_disable:
wlan_switch_regulators(0);
wlan_powered_up = false;
pr_info("WLAN power-down failed\n");
return rc;
}
void __init qrd7627a_add_io_devices(void)
{
int rc;
/* touchscreen */
if (machine_is_msm7627a_qrd1()) {
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
synaptic_i2c_clearpad3k,
ARRAY_SIZE(synaptic_i2c_clearpad3k));
} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_evt()) {
/* Use configuration data for EVT */
if (machine_is_msm8625_evt()) {
mxt_config_array[0].config = mxt_config_data_evt;
mxt_config_array[0].config_length =
ARRAY_SIZE(mxt_config_data_evt);
mxt_platform_data.panel_maxy = 875;
mxt_vkey_setup();
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_IRQ_GPIO, 0,
GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_IRQ_GPIO);
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_RESET_GPIO);
}
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
mxt_device_info,
ARRAY_SIZE(mxt_device_info));
} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) {
ft5x06_touchpad_setup();
}
/* headset */
platform_device_register(&hs_pdev);
/* vibrator */
#ifdef CONFIG_MSM_RPC_VIBRATOR
msm_init_pmic_vibrator();
#endif
/* keypad */
if (machine_is_msm8625_evt())
kp_matrix_info_8625.keymap = keymap_8625_evt;
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_evt())
platform_device_register(&kp_pdev_8625);
else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7())
platform_device_register(&kp_pdev_sku3);
/* leds */
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_evt()) {
platform_device_register(&pmic_mpp_leds_pdev);
platform_device_register(&tricolor_leds_pdev);
}
}
/* FIH-SW-MM-VH-DISPLAY-JB00*[ */
void __init msm_fb_add_devices(void)
{
/* int rc = 0; */
msm7x27a_set_display_params(prim_panel_name);
if (machine_is_msm7627a_qrd1())
platform_add_devices(qrd_fb_devices,
ARRAY_SIZE(qrd_fb_devices));
else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_evt()) {
mipi_NT35510_pdata.bl_lock = 1;
mipi_NT35516_pdata.bl_lock = 1;
if (disable_splash)
mdp_pdata.cont_splash_enabled = 0x0;
platform_add_devices(evb_fb_devices,
ARRAY_SIZE(evb_fb_devices));
} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) {
sku3_lcdc_lcd_camera_power_init();
mdp_pdata.cont_splash_enabled = 0x0;
platform_add_devices(qrd3_fb_devices,
ARRAY_SIZE(qrd3_fb_devices));
} else {
mdp_pdata.cont_splash_enabled = 0x0;
platform_add_devices(msm_fb_devices,
ARRAY_SIZE(msm_fb_devices));
}
msm_fb_register_device("mdp", &mdp_pdata);
if (0){
if (machine_is_msm7625a_surf() || machine_is_msm7x27a_surf() ||
machine_is_msm8625_surf() || machine_is_msm7627a_qrd3()
|| machine_is_msm8625_qrd7())
msm_fb_register_device("lcdc", &lcdc_pdata);
}
#ifdef CONFIG_FB_MSM_MIPI_DSI
msm_fb_register_device("mipi_dsi", &mipi_dsi_pdata);
#endif
#if 0
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_evt()) {
gpio_reg_2p85v = regulator_get(&mipi_dsi_device.dev,
"lcd_vdd");
if (IS_ERR(gpio_reg_2p85v))
pr_err("%s:ext_2p85v regulator get failed", __func__);
gpio_reg_1p8v = regulator_get(&mipi_dsi_device.dev,
"lcd_vddi");
if (IS_ERR(gpio_reg_1p8v))
pr_err("%s:ext_1p8v regulator get failed", __func__);
if (mdp_pdata.cont_splash_enabled) {
/*Enable EXT_2.85 and 1.8 regulators*/
rc = regulator_enable(gpio_reg_2p85v);
if (rc < 0)
pr_err("%s: reg enable failed\n", __func__);
rc = regulator_enable(gpio_reg_1p8v);
if (rc < 0)
pr_err("%s: reg enable failed\n", __func__);
}
}
#endif
}
void __init qrd7627a_add_io_devices(void)
{
int rc;
int i; //hanjue
/* touchscreen */
if (machine_is_msm7627a_qrd1()) {
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
synaptic_i2c_clearpad3k,
ARRAY_SIZE(synaptic_i2c_clearpad3k));
} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
#if 1 //linxc 2012-12-21 +++
if (machine_is_msm8625_qrd5()) {
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
himax_ts_i2c_info,
ARRAY_SIZE(himax_ts_i2c_info));
}
#else
/* Use configuration data for sku5 */
if (machine_is_msm8625_qrd5()) {
mxt_config_array[0].config = mxt_config_data_qrd5;
mxt_config_array[0].config_length =
ARRAY_SIZE(mxt_config_data_qrd5);
mxt_platform_data.panel_maxy = 875;
mxt_platform_data.need_calibration = true;
mxt_vkey_setup();
}
if (machine_is_msm7x27a_qrd5a()) {
mxt_config_array[0].config = mxt_config_data_qrd5a;
mxt_config_array[0].config_length =
ARRAY_SIZE(mxt_config_data_qrd5a);
mxt_platform_data.panel_maxy = 875;
mxt_vkey_setup();
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_IRQ_GPIO, 0,
GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_IRQ_GPIO);
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_RESET_GPIO);
}
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
mxt_device_info,
ARRAY_SIZE(mxt_device_info));
#endif //linxc 2012-12-21 ---
} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7() || machine_is_msm8625q_skud() || machine_is_msm8625q_skue()) {
ft5x06_touchpad_setup();
}
/* headset */
platform_device_register(&hs_pdev);
/* vibrator */
#ifdef CONFIG_MSM_RPC_VIBRATOR
msm_init_pmic_vibrator();
#endif
//add by hanjue
/* change the keymap for qrd sku5 */
if(machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
kp_matrix_info_8625.keymap = keymap_8625_qrd5;
kp_matrix_info_8625.output_gpios = kp_row_gpios_8625_qrd5;
kp_matrix_info_8625.noutputs = ARRAY_SIZE(kp_row_gpios_8625_qrd5);
for (i = 0; i < kp_matrix_info_8625.noutputs; i++) {
rc = gpio_tlmm_config(GPIO_CFG(kp_matrix_info_8625.output_gpios[i], 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, kp_matrix_info_8625.output_gpios[i]);
}
}
for (i = 0; i < kp_matrix_info_8625.ninputs; i++) {
rc = gpio_tlmm_config(GPIO_CFG(kp_matrix_info_8625.input_gpios[i], 0,
GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
GPIO_CFG_2MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, kp_matrix_info_8625.input_gpios[i]);
}
}
}
/* keypad */
if (machine_is_msm7627a_evb() ||
machine_is_msm8625_evb()||
machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a() ||
machine_is_msm8625_qrd7())
platform_device_register(&kp_pdev_8625);
else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7())
platform_device_register(&kp_pdev_qrd3);
else if (machine_is_msm8625q_skud())
platform_device_register(&kp_pdev_skud);
#if 0
/* keypad */
if (machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a())
kp_matrix_info_8625.keymap = keymap_8625_qrd5;
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a())
platform_device_register(&kp_pdev_8625);
else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7())
platform_device_register(&kp_pdev_qrd3);
else if (machine_is_msm8625q_skud())
platform_device_register(&kp_pdev_skud);
#endif
/*start by lf 2012.12.26 */
#if 0
/* leds */
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
platform_device_register(&pmic_mpp_leds_pdev);
platform_device_register(&tricolor_leds_pdev);
} else if (machine_is_msm8625q_skud()) {
platform_device_register(&pmic_mpp_leds_pdev_skud);
/* enable the skud flash and torch by gpio leds driver */
platform_device_register(&gpio_flash_skud);
}
#endif
/*end by lf 2012.12.26 */
#ifdef CONFIG_LEDS_TRICOLOR_FLAHSLIGHT
/*tricolor leds init*/
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
platform_device_register(&msm_device_tricolor_leds);
tricolor_leds_gpio_setup();
}
#endif
}
static void __init msm7x27a_init_cam(void)
{
if (!(machine_is_msm7x27a_ffa() || machine_is_msm7625a_ffa()
|| machine_is_msm7627a_qrd1()
|| machine_is_msm8625_ffa())) {
/* LGE_CHANGE_S: 2012/11/2 [email protected] U0 Camera Bring Up */
#ifdef CONFIG_MACH_LGE
#ifdef CONFIG_HI542
sensor_board_info_hi542.cam_vreg = NULL;
sensor_board_info_hi542.num_vreg = 0;
#endif
#ifdef CONFIG_MT9E013_LGIT
mt9e013_lgit_sensor_info.cam_vreg = NULL;
mt9e013_lgit_sensor_info.num_vreg = 0;
#endif
#ifdef CONFIG_MT9V113
sensor_board_info_mt9v113.cam_vreg = NULL;
sensor_board_info_mt9v113.num_vreg = 0;
#endif
#else
#ifdef CONFIG_S5K4E1
sensor_board_info_s5k4e1.cam_vreg = NULL;
sensor_board_info_s5k4e1.num_vreg = 0;
#endif
#ifdef CONFIG_MT9E013
sensor_board_info_mt9e013.cam_vreg = NULL;
sensor_board_info_mt9e013.num_vreg = 0;
#endif
#ifdef CONFIG_WEBCAM_OV9726
sensor_board_info_ov9726.cam_vreg = NULL;
sensor_board_info_ov9726.num_vreg = 0;
#endif
#ifdef CONFIG_OV7692
sensor_board_info_ov7692.cam_vreg = NULL;
sensor_board_info_ov7692.num_vreg = 0;
#endif
#ifdef CONFIG_OV5647
sensor_board_info_ov5647.cam_vreg = NULL;
sensor_board_info_ov5647.num_vreg = 0;
#endif
sensor_board_info_ov8825.cam_vreg = NULL;
sensor_board_info_ov8825.num_vreg = 0;
#endif
/* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Camera Bring Up */
}
if (machine_is_msm8625_evb()
|| machine_is_msm8625_evt()) {
#ifdef CONFIG_OV7692
sensor_board_info_ov7692.cam_vreg =
ov7692_gpio_vreg;
sensor_board_info_ov7692.num_vreg =
ARRAY_SIZE(ov7692_gpio_vreg);
#endif
#ifdef CONFIG_OV5647
sensor_board_info_ov5647.cam_vreg =
ov5647_gpio_vreg;
sensor_board_info_ov5647.num_vreg =
ARRAY_SIZE(ov5647_gpio_vreg);
#endif
/* LGE_CHANGE_S: 2012/11/2 [email protected] U0 Camera Bring Up */
#ifndef CONFIG_MACH_LGE
sensor_board_info_ov8825.cam_vreg =
ov8825_gpio_vreg;
sensor_board_info_ov8825.num_vreg =
ARRAY_SIZE(ov8825_gpio_vreg);
#endif
/* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Camera Bring Up */
}
platform_device_register(&msm_camera_server);
/* LGE_CHANGE_S: 2012/11/2 [email protected] U0 Camera Bring Up */
#ifndef CONFIG_MACH_LGE
if (machine_is_msm8625_surf() || machine_is_msm8625_evb()
|| machine_is_msm8625_evt()
|| machine_is_msm8625_qrd7()
|| machine_is_msm7x27a_u0()) {
platform_device_register(&msm8625_device_csic0);
platform_device_register(&msm8625_device_csic1);
} else {
platform_device_register(&msm7x27a_device_csic0);
platform_device_register(&msm7x27a_device_csic1);
}
#endif
platform_device_register(&msm7x27a_device_csic0);
platform_device_register(&msm7x27a_device_csic1);
/* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Camera Bring Up */
if (machine_is_msm8625_evb()
|| machine_is_msm8625_evt()
|| machine_is_msm8625_qrd7())
*(int *) msm7x27a_device_clkctl.dev.platform_data = 1;
platform_device_register(&msm7x27a_device_clkctl);
platform_device_register(&msm7x27a_device_vfe);
}
/* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Flash Porting */ void __init msm7627a_camera_init(void) { #ifndef CONFIG_MSM_CAMERA_V4L2 int rc; #endif pr_debug("msm7627a_camera_init Entered\n"); if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) { #ifdef CONFIG_OV7692 ov7692_cam_req_gpio[0].gpio = GPIO_SKU7_CAM_VGA_SHDN; ov7692_cam_gpio_set_tbl[0].gpio = GPIO_SKU7_CAM_VGA_SHDN; ov7692_cam_gpio_set_tbl[1].gpio = GPIO_SKU7_CAM_VGA_SHDN; msm_camera_sensor_ov5647_data.sensor_pwd = GPIO_SKU7_CAM_5MP_SHDN_N; msm_camera_sensor_ov5647_data.sensor_reset = GPIO_SKU7_CAM_5MP_CAMIF_RESET; #endif } /* LCD and camera power (VREG & LDO) init */ if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() || machine_is_msm8625_evt() || machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) { #ifndef CONFIG_MSM_CAMERA_V4L2 lcd_camera_power_init(); #endif #ifdef CONFIG_OV5647 evb_camera_gpio_cfg(); #endif } #ifndef CONFIG_MSM_CAMERA_V4L2 if (machine_is_msm7627a_qrd1()) { qrd1_camera_gpio_cfg(); platform_add_devices(camera_devices_qrd, ARRAY_SIZE(camera_devices_qrd)); } else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() || machine_is_msm8625_evt() || machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) { platform_add_devices(camera_devices_evb, ARRAY_SIZE(camera_devices_evb)); } else if (machine_is_msm7627a_qrd3()) return; else platform_add_devices(camera_devices_msm, ARRAY_SIZE(camera_devices_msm)); #endif /* LGE_CHANGE_S: 2012/11/2 [email protected] U0 Camera Bring Up */ #ifndef CONFIG_MACH_LGE if (!machine_is_msm7627a_qrd1() || !machine_is_msm7627a_evb() || !machine_is_msm8625_evb() || !machine_is_msm8625_evt() || !machine_is_msm7627a_qrd3() || !machine_is_msm8625_qrd7()) register_i2c_devices(); #endif /* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Camera Bring Up */ #ifndef CONFIG_MSM_CAMERA_V4L2 rc = regulator_bulk_get(NULL, ARRAY_SIZE(regs_camera), regs_camera); if (rc) { pr_err("%s: could not get regulators: %d\n", __func__, rc); return; } rc = regulator_bulk_set_voltage(ARRAY_SIZE(regs_camera), regs_camera); if (rc) { pr_err("%s: could not set voltages: %d\n", __func__, rc); return; } #endif #if defined(CONFIG_MSM_CAMERA_V4L2) msm7x27a_init_cam(); #endif #ifndef CONFIG_MSM_CAMERA_V4L2 if (machine_is_msm7627a_qrd1()) { i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID, i2c_camera_devices_qrd, ARRAY_SIZE(i2c_camera_devices_qrd)); } else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() || machine_is_msm8625_evt() || machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()) { pr_debug("machine_is_msm7627a_evb i2c_register_board_info\n"); i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID, i2c_camera_devices_evb, ARRAY_SIZE(i2c_camera_devices_evb)); } else #endif pr_debug("i2c_register_board_info\n"); i2c_register_board_info(MSM_GSBI0_QUP_I2C_BUS_ID, i2c_camera_devices, ARRAY_SIZE(i2c_camera_devices)); /* LGE_CHANGE_S: 2012/11/2 [email protected] U0 Camera Bring Up */ #ifdef CONFIG_LEDS_AS364X lge_add_gpio_i2c_device(lge_init_i2c_camera); #endif /* LGE_CHANGE_E: 2012/11/2 [email protected] U0 Camera Bring Up */ }
void __init qrd7627a_add_io_devices(void)
{
int rc;
/* touchscreen */
if (machine_is_msm7627a_qrd1()) {
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
synaptic_i2c_clearpad3k,
ARRAY_SIZE(synaptic_i2c_clearpad3k));
} else if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
/* Use configuration data for sku5 */
if (machine_is_msm8625_qrd5()) {
mxt_config_array[0].config = mxt_config_data_qrd5;
mxt_config_array[0].config_length =
ARRAY_SIZE(mxt_config_data_qrd5);
mxt_platform_data.panel_maxy = 875;
mxt_platform_data.need_calibration = true;
mxt_vkey_setup();
}
if (machine_is_msm7x27a_qrd5a()) {
mxt_config_array[0].config = mxt_config_data_qrd5a;
mxt_config_array[0].config_length =
ARRAY_SIZE(mxt_config_data_qrd5a);
mxt_platform_data.panel_maxy = 875;
mxt_vkey_setup();
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_IRQ_GPIO, 0,
GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_IRQ_GPIO);
}
rc = gpio_tlmm_config(GPIO_CFG(MXT_TS_RESET_GPIO, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
if (rc) {
pr_err("%s: gpio_tlmm_config for %d failed\n",
__func__, MXT_TS_RESET_GPIO);
}
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
mxt_device_info,
ARRAY_SIZE(mxt_device_info));
} else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7()
|| machine_is_msm8625q_skud()
|| machine_is_msm8625q_evbd()
|| machine_is_msm8625q_skue()) {
ft5x06_touchpad_setup();
/* evbd+ can support synaptic as well */
if (machine_is_msm8625q_evbd() &&
(socinfo_get_platform_type() == 0x13)) {
/* for QPR EVBD+ with synaptic touch panel */
/* TODO: Add gpio request to the driver
to support proper dynamic touch detection */
gpio_tlmm_config(
GPIO_CFG(CLEARPAD3000_ATTEN_GPIO_EVBD_PLUS, 0,
GPIO_CFG_INPUT, GPIO_CFG_NO_PULL,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
gpio_tlmm_config(
GPIO_CFG(CLEARPAD3000_RESET_GPIO, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
gpio_set_value(CLEARPAD3000_RESET_GPIO, 0);
usleep(10000);
gpio_set_value(CLEARPAD3000_RESET_GPIO, 1);
usleep(50000);
i2c_register_board_info(MSM_GSBI1_QUP_I2C_BUS_ID,
rmi4_i2c_devices,
ARRAY_SIZE(rmi4_i2c_devices));
}
}
/* headset */
platform_device_register(&hs_pdev);
/* vibrator */
#ifdef CONFIG_MSM_RPC_VIBRATOR
msm_init_pmic_vibrator();
#endif
/* keypad */
if (machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a())
kp_matrix_info_8625.keymap = keymap_8625_qrd5;
/* keypad info for EVBD+ */
if (machine_is_msm8625q_evbd() &&
(socinfo_get_platform_type() == 13)) {
gpio_tlmm_config(GPIO_CFG(37, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
gpio_tlmm_config(GPIO_CFG(42, 0,
GPIO_CFG_OUTPUT, GPIO_CFG_PULL_DOWN,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
gpio_tlmm_config(GPIO_CFG(31, 0,
GPIO_CFG_INPUT, GPIO_CFG_PULL_UP,
GPIO_CFG_8MA), GPIO_CFG_ENABLE);
kp_matrix_info_skud.output_gpios = kp_row_gpios_evbdp;
kp_matrix_info_skud.input_gpios = kp_col_gpios_evbdp;
kp_matrix_info_skud.noutputs = ARRAY_SIZE(kp_row_gpios_evbdp);
kp_matrix_info_skud.ninputs = ARRAY_SIZE(kp_col_gpios_evbdp);
}
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb() ||
machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a())
platform_device_register(&kp_pdev_8625);
else if (machine_is_msm7627a_qrd3() || machine_is_msm8625_qrd7())
platform_device_register(&kp_pdev_qrd3);
else if (machine_is_msm8625q_skud()||machine_is_msm8625q_evbd())
platform_device_register(&kp_pdev_skud);
else if (machine_is_msm8625q_skue())
platform_device_register(&kp_pdev_skue);
/* leds */
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
platform_device_register(&pmic_mpp_leds_pdev);
platform_device_register(&tricolor_leds_pdev);
} else if (machine_is_msm8625q_skud() || machine_is_msm8625q_evbd()) {
platform_device_register(&pmic_mpp_leds_pdev_skud);
/* enable the skud flash and torch by gpio leds driver */
platform_device_register(&gpio_flash_skud);
} else if (machine_is_msm8625q_skue()) {
/* enable the skue flashlight by gpio leds driver */
platform_device_register(&gpio_flash_skue);
}
#ifdef CONFIG_LEDS_TRICOLOR_FLAHSLIGHT
/*tricolor leds init*/
if (machine_is_msm7627a_evb() || machine_is_msm8625_evb()
|| machine_is_msm8625_qrd5() || machine_is_msm7x27a_qrd5a()) {
platform_device_register(&msm_device_tricolor_leds);
tricolor_leds_gpio_setup();
}
#endif
}
