static state_t menuLidOpenDur(button_t button)
{
if (button == BUTTON_ENTER)
{
lcdprint_P(PSTR("Lid open timer"), true);
editInt = pid.getLidOpenDuration();
}
else if (button == BUTTON_LEAVE)
{
storeLidParam(LIDPARAM_DURATION, editInt);
}
menuNumberEdit(button, 10, 0, 1000, PSTR("%3d seconds"));
return ST_AUTO;
}
static state_t menuProbeOffset(button_t button)
{
unsigned char probeIndex = Menus.getState() - ST_PROBEOFF0;
if (button == BUTTON_ENTER)
{
menuProbenameLine(probeIndex);
editInt = pid.Probes[probeIndex]->Offset;
}
else if (button == BUTTON_LEAVE)
storeAndReportProbeOffset(probeIndex, editInt);
menuNumberEdit(button, 1, -100, 100, PSTR("Offset %4d"DEGREE"%c"));
return ST_AUTO;
}
static state_t menuLidOpenOff(button_t button)
{
if (button == BUTTON_ENTER)
{
lcdprint_P(PSTR("Lid open offset"), true);
editInt = pid.LidOpenOffset;
}
else if (button == BUTTON_LEAVE)
{
storeLidParam(LIDPARAM_OFFSET, editInt);
}
menuNumberEdit(button, 1, 0, 100, PSTR("%3d%% below set"));
return ST_AUTO;
}
static state_t menuSetpoint(button_t button)
{
if (button == BUTTON_ENTER)
{
lcd.clear();
lcd.print(F("Cooling setpoint"));
editInt = g_SetPoint;
}
else if (isEditing && button == BUTTON_CENTER)
{
setSetPoint(editInt);
}
return menuNumberEdit(button, 1, -40, 100, PSTR(" %3d"DEGREE"%c "));
}
static state_t menuMaxFanSpeed(button_t button)
{
if (button == BUTTON_ENTER)
{
lcdprint_P(PSTR("Maximum auto fan"), true);
editInt = pid.getFanMaxSpeed();
}
else if (button == BUTTON_LEAVE)
{
if (editInt != pid.getFanMaxSpeed())
storeAndReportMaxFanSpeed(editInt);
}
menuNumberEdit(button, 5, 0, 100, PSTR("speed %3d%%"));
return ST_AUTO;
}
state_t menuLcdBrightness(button_t button)
{
if (button == BUTTON_ENTER)
{
lcd.clear();
lcd.print(F("LCD brightness"));
editInt = rgb.getBrightness();
}
else if (isEditing && button == BUTTON_CENTER)
configChanged();
state_t r = menuNumberEdit(button, 10, 10, 100, PSTR(" %3d%% "));
if (isEditing && button & (BUTTON_LEFT | BUTTON_RIGHT))
rgb.setBrightness(editInt);
return r;
}
static state_t menuMinRunTime(button_t button)
{
if (button == BUTTON_ENTER)
{
lcd.clear();
lcd.print(F("Min ON time"));
editInt = g_MinRunTime;
}
else if (isEditing && button == BUTTON_CENTER)
{
g_MinRunTime = editInt;
configChanged();
}
return menuNumberEdit(button, 1, 0, 30, PSTR(" %3d minutes "));
}
static state_t menuCutOutDifferential(button_t button)
{
if (button == BUTTON_ENTER)
{
lcd.clear();
lcd.print(F("Cutout diff"));
editInt = g_CutoutOffset;
}
else if (isEditing && button == BUTTON_CENTER)
{
g_CutoutOffset = editInt;
configChanged();
}
return menuNumberEdit(button, 1, 0, 30, PSTR(" %3d"DEGREE"%c "));
}
static state_t menuSetpoint(button_t button)
{
if (button == BUTTON_ENTER)
{
lcdprint_P(PSTR("Set temperature:"), true);
editInt = pid.getSetPoint();
}
else if (button == BUTTON_LEAVE)
{
// Check to see if it is different because the setPoint
// field stores either the setPoint or manual mode
if (editInt != pid.getSetPoint())
storeSetPoint(editInt);
}
menuNumberEdit(button, 5, 0, 1000, PSTR("%3d"DEGREE"%c"));
return ST_AUTO;
}
static state_t menuLcdBacklight(button_t button)
{
if (button == BUTTON_ENTER)
{
lcdprint_P(PSTR("LCD brightness"), true);
editInt = g_LcdBacklight;
}
else if (button == BUTTON_LEAVE)
{
if (editInt != g_LcdBacklight)
{
storeLcdBacklight(editInt);
reportLcdParameters();
}
}
menuNumberEdit(button, 10, 0, 100, PSTR("%3d%%"));
setLcdBacklight(0x80 | editInt);
return ST_AUTO;
}
