static int __init omap4_i2c_init(void)
{
omap_i2c_hwspinlock_init(1, 0, &sdp4430_i2c_1_bus_pdata);
omap_i2c_hwspinlock_init(2, 1, &sdp4430_i2c_2_bus_pdata);
omap_i2c_hwspinlock_init(3, 2, &sdp4430_i2c_3_bus_pdata);
omap_i2c_hwspinlock_init(4, 3, &sdp4430_i2c_4_bus_pdata);
omap_register_i2c_bus_board_data(1, &sdp4430_i2c_1_bus_pdata);
omap_register_i2c_bus_board_data(2, &sdp4430_i2c_2_bus_pdata);
omap_register_i2c_bus_board_data(3, &sdp4430_i2c_3_bus_pdata);
omap_register_i2c_bus_board_data(4, &sdp4430_i2c_4_bus_pdata);
omap4_pmic_init("twl6030", &tablet_twldata); // i2c_register_board_info(1, &sdp4430_i2c_boardinfo, 1);
#ifdef CONFIG_INPUT_KXTF9
kxtf9_gpio_for_irq = 66;
sdp4430_i2c_boardinfo[I2C_INDEX_1_KXTF9].irq = OMAP_GPIO_IRQ(kxtf9_gpio_for_irq);
kxtf9_dev_init();
#endif //CONFIG_INPUT_KXTF9
#ifdef CONFIG_BATTERY_MAX17042
max17042_gpio_for_irq = 65;
sdp4430_i2c_boardinfo[I2C_INDEX_1_MAX17042].irq = OMAP_GPIO_IRQ(max17042_gpio_for_irq);
max17042_dev_init();
#endif //CONFIG_BATTERY_MAX17042
i2c_register_board_info(1, sdp4430_i2c_boardinfo, ARRAY_SIZE(sdp4430_i2c_boardinfo));
i2c_register_board_info(2, tablet_i2c_3_boardinfo, ARRAY_SIZE(tablet_i2c_3_boardinfo));
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
omap_register_i2c_bus(4, 400, NULL, 0);
omap2_i2c_pullup(3, I2C_PULLUP_STD_860_OM_FAST_500_OM);
/*
* This will allow unused regulator to be shutdown. This flag
* should be set in the board file. Before regulators are registered.
*/
regulator_has_full_constraints();
/*
* Drive MSECURE high for TWL6030 write access.
*/
omap_mux_init_signal("fref_clk0_out.gpio_wk6", OMAP_PIN_OUTPUT);
gpio_request(6, "msecure");
gpio_direction_output(6, 1);
return 0;
}
static int __init omap4_i2c_init(void)
{
omap_i2c_hwspinlock_init(1, 0, &sdp4430_i2c_1_bus_pdata);
omap_i2c_hwspinlock_init(2, 1, &sdp4430_i2c_2_bus_pdata);
omap_i2c_hwspinlock_init(3, 2, &sdp4430_i2c_3_bus_pdata);
omap_i2c_hwspinlock_init(4, 3, &sdp4430_i2c_4_bus_pdata);
omap_register_i2c_bus_board_data(1, &sdp4430_i2c_1_bus_pdata);
omap_register_i2c_bus_board_data(2, &sdp4430_i2c_2_bus_pdata);
omap_register_i2c_bus_board_data(3, &sdp4430_i2c_3_bus_pdata);
omap_register_i2c_bus_board_data(4, &sdp4430_i2c_4_bus_pdata);
/*
* VCORE3 & VMEM are not used in 4460. By register it to regulator
* framework will ensures that resources are disabled.
*/
if (cpu_is_omap446x()) {
tablet_twldata.vdd3 = &tablet_vcore3;
tablet_twldata.vmem = &tablet_vmem;
}
omap4_pmic_init("twl6030", &tablet_twldata);
i2c_register_board_info(1, sdp4430_i2c_boardinfo,
ARRAY_SIZE(sdp4430_i2c_boardinfo));
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, tablet_i2c_3_boardinfo,
ARRAY_SIZE(tablet_i2c_3_boardinfo));
omap_register_i2c_bus(4, 400, NULL, 0);
omap2_i2c_pullup(3, I2C_PULLUP_STD_860_OM_FAST_500_OM);
/*
* This will allow unused regulator to be shutdown. This flag
* should be set in the board file. Before regulators are registered.
*/
regulator_has_full_constraints();
/*
* Drive MSECURE high for TWL6030 write access.
*/
omap_mux_init_signal("fref_clk0_out.gpio_wk6", OMAP_PIN_OUTPUT);
gpio_request(6, "msecure");
gpio_direction_output(6, 1);
return 0;
}
static int __init omap4_i2c_init(void)
{
omap_i2c_hwspinlock_init(1, 0, &sdp4430_i2c_1_bus_pdata);
omap_i2c_hwspinlock_init(2, 1, &sdp4430_i2c_2_bus_pdata);
omap_i2c_hwspinlock_init(3, 2, &sdp4430_i2c_3_bus_pdata);
omap_i2c_hwspinlock_init(4, 3, &sdp4430_i2c_4_bus_pdata);
omap_register_i2c_bus_board_data(1, &sdp4430_i2c_1_bus_pdata);
omap_register_i2c_bus_board_data(2, &sdp4430_i2c_2_bus_pdata);
omap_register_i2c_bus_board_data(3, &sdp4430_i2c_3_bus_pdata);
omap_register_i2c_bus_board_data(4, &sdp4430_i2c_4_bus_pdata);
omap4_pmic_init("twl6030", &sdp4430_twldata);
/*SW5, Jamestsai, 1213, enable cypress{*/
//omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(2, 400, sdp4430_i2c_2_boardinfo,
ARRAY_SIZE(sdp4430_i2c_2_boardinfo));
/*}SW5, Jamestsai, 1213, enable cypress*/
/* JossCheng, 20111221, change clock of i2c bus3 to be 400K Hz { */
omap_register_i2c_bus(3, 400, sdp4430_i2c_3_boardinfo,
ARRAY_SIZE(sdp4430_i2c_3_boardinfo));
/* JossCheng, 20111221, change clock of i2c bus3 to be 400K Hz } */
omap_register_i2c_bus(4, 400, sdp4430_i2c_4_boardinfo,
ARRAY_SIZE(sdp4430_i2c_4_boardinfo));
#ifdef CONFIG_MACH_OMAP4_BOWSER_SUBTYPE_JEM
omap2_i2c_pullup(3, I2C_PULLUP_STD_860_OM_FAST_500_OM);
#endif
/*
* This will allow unused regulator to be shutdown. This flag
* should be set in the board file. Before regulators are registered.
*/
regulator_has_full_constraints();
/*
* Drive MSECURE high for TWL6030/6032 write access.
*/
omap_mux_init_signal("fref_clk3_req.gpio_wk30", OMAP_PIN_OUTPUT);
gpio_request(30, "msecure");
gpio_direction_output(30, 1);
return 0;
}
static int __init acclaim_i2c_init(void)
{
int err;
acclaim_i2c_hwspinlock_init(1, 0, &acclaim_i2c_1_bus_pdata);
acclaim_i2c_hwspinlock_init(2, 1, &acclaim_i2c_2_bus_pdata);
acclaim_i2c_hwspinlock_init(3, 2, &acclaim_i2c_3_bus_pdata);
acclaim_i2c_hwspinlock_init(4, 3, &acclaim_i2c_4_bus_pdata);
omap_register_i2c_bus_board_data(1, &acclaim_i2c_1_bus_pdata);
omap_register_i2c_bus_board_data(2, &acclaim_i2c_2_bus_pdata);
omap_register_i2c_bus_board_data(3, &acclaim_i2c_3_bus_pdata);
omap_register_i2c_bus_board_data(4, &acclaim_i2c_4_bus_pdata);
omap4_pmic_init("twl6030", &acclaim_twldata);
err = i2c_register_board_info(1,
acclaim_i2c_1_boardinfo,
ARRAY_SIZE(acclaim_i2c_1_boardinfo));
if (err)
return err;
omap_register_i2c_bus(2, 400, acclaim_i2c_2_boardinfo,
ARRAY_SIZE(acclaim_i2c_2_boardinfo));
omap_register_i2c_bus(3, 400, NULL, 0);
omap_register_i2c_bus(4, 400, NULL, 0);
omap2_i2c_pullup(3, I2C_PULLUP_STD_860_OM_FAST_500_OM);
/*
* This will allow unused regulator to be shutdown. This flag
* should be set in the board file. Before regulators are registered.
*/
regulator_has_full_constraints();
return 0;
}
static int __init omap4_i2c_init(void)
{
omap_i2c_hwspinlock_init(1, 0, &sdp4430_i2c_1_bus_pdata);
omap_i2c_hwspinlock_init(2, 1, &sdp4430_i2c_2_bus_pdata);
omap_i2c_hwspinlock_init(3, 2, &sdp4430_i2c_3_bus_pdata);
omap_i2c_hwspinlock_init(4, 3, &sdp4430_i2c_4_bus_pdata);
omap_register_i2c_bus_board_data(1, &sdp4430_i2c_1_bus_pdata);
omap_register_i2c_bus_board_data(2, &sdp4430_i2c_2_bus_pdata);
omap_register_i2c_bus_board_data(3, &sdp4430_i2c_3_bus_pdata);
omap_register_i2c_bus_board_data(4, &sdp4430_i2c_4_bus_pdata);
omap4_power_init();
i2c_register_board_info(1, sdp4430_i2c_boardinfo,
ARRAY_SIZE(sdp4430_i2c_boardinfo));
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
omap_register_i2c_bus(4, 400, NULL, 0);
omap2_i2c_pullup(3, I2C_PULLUP_STD_860_OM_FAST_500_OM);
/*
* This will allow unused regulator to be shutdown. This flag
* should be set in the board file. Before regulators are registered.
*/
regulator_has_full_constraints();
/*
* Drive MSECURE high for TWL6030/6032 write access.
*/
omap_mux_init_signal("fref_clk0_out.gpio_wk6", OMAP_PIN_OUTPUT);
gpio_request(6, "msecure");
gpio_direction_output(6, 1);
return 0;
}
