void NcpSpi::PrepareNextSpiSendFrame(void)
{
otError error = OT_ERROR_NONE;
uint16_t frameLength;
uint16_t readLength;
SpiFrame sendFrame(mSendFrame);
VerifyOrExit(!mTxFrameBuffer.IsEmpty());
if (ShouldWakeHost())
{
otPlatWakeHost();
}
SuccessOrExit(error = mTxFrameBuffer.OutFrameBegin());
frameLength = mTxFrameBuffer.OutFrameGetLength();
assert(frameLength <= kSpiBufferSize - kSpiHeaderSize);
// The "accept length" in `mSendFrame` is already updated based
// on current state of receive. It is changed either from the
// `SpiTransactionComplete()` callback or from `HandleRxFrame()`.
readLength = mTxFrameBuffer.OutFrameRead(frameLength, sendFrame.GetData());
assert(readLength == frameLength);
sendFrame.SetHeaderDataLen(frameLength);
mSendFrameLength = frameLength + kSpiHeaderSize;
mTxState = kTxStateSending;
// Prepare new transaction by using `mSendFrame` as the output
// frame while keeping the input frame unchanged.
error = otPlatSpiSlavePrepareTransaction(mSendFrame, mSendFrameLength, NULL, 0, /* aRequestTrans */ true);
if (error == OT_ERROR_BUSY)
{
// Being busy is OK. We will get the transaction set up
// properly when the current transaction is completed.
error = OT_ERROR_NONE;
}
if (error != OT_ERROR_NONE)
{
mTxState = kTxStateIdle;
mPrepareTxFrameTask.Post();
ExitNow();
}
mTxFrameBuffer.OutFrameRemove();
exit:
return;
}
// This method encodes a frame from the tx frame buffer (mTxFrameBuffer) into the uart buffer and sends it over uart.
// If the uart buffer gets full, it sends the current encoded portion. This method remembers current state, so on
// sub-sequent calls, it restarts encoding the bytes from where it left of in the frame .
void NcpUart::EncodeAndSendToUart(void)
{
uint16_t len;
bool prevHostPowerState;
#if OPENTHREAD_ENABLE_NCP_SPINEL_ENCRYPTER
NcpFrameBufferEncrypterReader &txFrameBuffer = mTxFrameBufferEncrypterReader;
#else
NcpFrameBuffer &txFrameBuffer = mTxFrameBuffer;
#endif // OPENTHREAD_ENABLE_NCP_SPINEL_ENCRYPTER
while (!txFrameBuffer.IsEmpty() || (mState == kFinalizingFrame))
{
switch (mState)
{
case kStartingFrame:
if (super_t::ShouldWakeHost())
{
otPlatWakeHost();
}
VerifyOrExit(super_t::ShouldDeferHostSend() == false);
SuccessOrExit(mFrameEncoder.Init(mUartBuffer));
txFrameBuffer.OutFrameBegin();
mState = kEncodingFrame;
while (!txFrameBuffer.OutFrameHasEnded())
{
mByte = txFrameBuffer.OutFrameReadByte();
case kEncodingFrame:
SuccessOrExit(mFrameEncoder.Encode(mByte, mUartBuffer));
}
// track the change of mHostPowerStateInProgress by the
// call to OutFrameRemove.
prevHostPowerState = mHostPowerStateInProgress;
txFrameBuffer.OutFrameRemove();
if (prevHostPowerState && !mHostPowerStateInProgress)
{
// If mHostPowerStateInProgress transitioned from true -> false
// in the call to OutFrameRemove, then the frame should be sent
// out the UART without attempting to push any new frames into
// the mUartBuffer. This is necessary to avoid prematurely calling
// otPlatWakeHost.
mUartSendImmediate = true;
}
mState = kFinalizingFrame;
// fall through
case kFinalizingFrame:
SuccessOrExit(mFrameEncoder.Finalize(mUartBuffer));
mState = kStartingFrame;
if (mUartSendImmediate)
{
// clear state and break;
mUartSendImmediate = false;
break;
}
}
}
exit:
len = mUartBuffer.GetLength();
if (len > 0)
{
if (otPlatUartSend(mUartBuffer.GetBuffer(), len) != OT_ERROR_NONE)
{
assert(false);
}
}
}
