void spindle_run(uint8_t direction, float rpm)
{
if (sys.state == STATE_CHECK_MODE) { return; }
// Empty planner buffer to ensure spindle is set when programmed.
protocol_auto_cycle_start(); //temp fix for M3 lockup
protocol_buffer_synchronize();
if (direction == SPINDLE_DISABLE) {
spindle_stop();
} else {
#ifndef USE_SPINDLE_DIR_AS_ENABLE_PIN
if (direction == SPINDLE_ENABLE_CW) {
SPINDLE_DIRECTION_PORT &= ~(1<<SPINDLE_DIRECTION_BIT);
} else {
SPINDLE_DIRECTION_PORT |= (1<<SPINDLE_DIRECTION_BIT);
}
#endif
#ifdef VARIABLE_SPINDLE
// TODO: Install the optional capability for frequency-based output for servos.
#define SPINDLE_RPM_RANGE (SPINDLE_MAX_RPM-SPINDLE_MIN_RPM)
#define RC_SERVO_RANGE (RC_SERVO_LONG-RC_SERVO_SHORT)
#ifdef CPU_MAP_ATMEGA2560
TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x07 | (1<<WAVE2_REGISTER) | (1<<WAVE3_REGISTER); // set to 1/1024 Prescaler
OCR4A = 0xFFFF; // set the top 16bit value
uint16_t current_pwm;
#else
TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x07; // set to 1/1024 Prescaler
uint8_t current_pwm;
#endif
if ( rpm < SPINDLE_MIN_RPM ) { rpm = 0; }
else {
rpm -= SPINDLE_MIN_RPM;
if ( rpm > SPINDLE_RPM_RANGE ) { rpm = SPINDLE_RPM_RANGE; } // Prevent integer overflow
}
#ifdef RC_SERVO_INVERT
current_pwm = floor( RC_SERVO_LONG - rpm*(RC_SERVO_RANGE/SPINDLE_RPM_RANGE));
OCR_REGISTER = current_pwm;
#else
current_pwm = floor( rpm*(RC_SERVO_RANGE/SPINDLE_RPM_RANGE) + RC_SERVO_SHORT);
OCR_REGISTER = current_pwm;
#endif
#ifdef MINIMUM_SPINDLE_PWM
if (current_pwm < MINIMUM_SPINDLE_PWM) { current_pwm = MINIMUM_SPINDLE_PWM; }
OCR_REGISTER = current_pwm;
#endif
#endif
}
}
// Method to store coord data parameters into EEPROM
void settings_write_coord_data(uint8_t coord_select, float *coord_data)
{
#ifdef FORCE_BUFFER_SYNC_DURING_EEPROM_WRITE
protocol_buffer_synchronize();
#endif
uint32_t addr = coord_select*(sizeof(float)*N_AXIS+1) + EEPROM_ADDR_PARAMETERS;
memcpy_to_eeprom_with_checksum(addr,(char*)coord_data, sizeof(float)*N_AXIS);
}
// Method to store startup lines into EEPROM
void settings_store_startup_line(uint8_t n, char *line)
{
#ifdef FORCE_BUFFER_SYNC_DURING_EEPROM_WRITE
protocol_buffer_synchronize(); // A startup line may contain a motion and be executing.
#endif
uint32_t addr = n*(LINE_BUFFER_SIZE+1)+EEPROM_ADDR_STARTUP_BLOCK;
memcpy_to_eeprom_with_checksum(addr,(char*)line, LINE_BUFFER_SIZE);
}
// Execute dwell in seconds.
void mc_dwell(float seconds)
{
if (sys.state == STATE_CHECK_MODE) { return; }
uint16_t i = floor(1000/DWELL_TIME_STEP*seconds);
protocol_buffer_synchronize();
delay_ms(floor(1000*seconds-i*DWELL_TIME_STEP)); // Delay millisecond remainder.
while (i-- > 0) {
// NOTE: Check and execute realtime commands during dwell every <= DWELL_TIME_STEP milliseconds.
protocol_execute_realtime();
if (sys.abort) { return; }
_delay_ms(DWELL_TIME_STEP); // Delay DWELL_TIME_STEP increment
}
}
void coolant_run(uint8_t mode)
{
protocol_buffer_synchronize(); // Ensure coolant turns on when specified in program.
if (mode == COOLANT_FLOOD_ENABLE) {
COOLANT_FLOOD_PORT |= (1 << COOLANT_FLOOD_BIT);
#ifdef ENABLE_M7
} else if (mode == COOLANT_MIST_ENABLE) {
COOLANT_MIST_PORT |= (1 << COOLANT_MIST_BIT);
#endif
} else {
coolant_stop();
}
}
void spindle_run(uint8_t direction, float rpm)
{
if (sys.state == STATE_CHECK_MODE) {
return;
}
// Empty planner buffer to ensure spindle is set when programmed.
protocol_auto_cycle_start(); //temp fix for M3 lockup
protocol_buffer_synchronize();
// Halt or set spindle direction and rpm.
if (direction == SPINDLE_DISABLE) {
spindle_stop();
} else {
if (direction == SPINDLE_ENABLE_CW) {
SPINDLE_DIRECTION_PORT &= ~(1<<SPINDLE_DIRECTION_BIT);
} else {
SPINDLE_DIRECTION_PORT |= (1<<SPINDLE_DIRECTION_BIT);
}
#ifdef VARIABLE_SPINDLE
#define SPINDLE_RPM_RANGE (SPINDLE_MAX_RPM-SPINDLE_MIN_RPM)
TCCRA_REGISTER = (1<<COMB_BIT) | (1<<WAVE1_REGISTER) | (1<<WAVE0_REGISTER);
TCCRB_REGISTER = (TCCRB_REGISTER & 0b11111000) | 0x02; // set to 1/8 Prescaler
rpm -= SPINDLE_MIN_RPM;
if ( rpm > SPINDLE_RPM_RANGE ) {
rpm = SPINDLE_RPM_RANGE; // Prevent uint8 overflow
}
uint8_t current_pwm = floor( rpm*(255.0/SPINDLE_RPM_RANGE) + 0.5);
OCR_REGISTER = current_pwm;
#ifndef CPU_MAP_ATMEGA328P // On the Uno, spindle enable and PWM are shared.
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
#endif
#else
SPINDLE_ENABLE_PORT |= (1<<SPINDLE_ENABLE_BIT);
#endif
}
}
void punch()
{
if (sys.state == STATE_CHECK_MODE) {
return ;
}
punch_stop();
// wait for current awaited commands
protocol_buffer_synchronize();
// wait for the end of move
do {
protocol_execute_realtime();
if (sys.abort) {
return;
}
} while ( sys.state != STATE_IDLE );
punch_activate_actuator(COMMAND_PUNCH_UNACTIVATED);
punch_activate_actuator(COMMAND_PUNCH_DOWN);
// wait_a_bit();
punch_wait_sensor_state(PUNCH_SENSOR_DOWN_BIT);
// wait_a_bit();
punch_activate_actuator(COMMAND_PUNCH_UNACTIVATED);
// wait_a_bit();
// activate the punch up
punch_activate_actuator(COMMAND_PUNCH_UP);
// wait_a_bit();
// activate the punch up, and release the down
punch_wait_sensor_state(PUNCH_SENSOR_UP_BIT);
// wait_a_bit();
}
void mc_probe_cycle(float *target, float feed_rate, uint8_t invert_feed_rate, uint8_t is_probe_away,
uint8_t is_no_error)
#endif
{
// TODO: Need to update this cycle so it obeys a non-auto cycle start.
if (sys.state == STATE_CHECK_MODE) { return; }
// Finish all queued commands and empty planner buffer before starting probe cycle.
protocol_buffer_synchronize();
// Initialize probing control variables
sys.probe_succeeded = false; // Re-initialize probe history before beginning cycle.
probe_configure_invert_mask(is_probe_away);
// After syncing, check if probe is already triggered. If so, halt and issue alarm.
// NOTE: This probe initialization error applies to all probing cycles.
if ( probe_get_state() ) { // Check probe pin state.
bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_PROBE_FAIL);
protocol_execute_realtime();
}
if (sys.abort) { return; } // Return if system reset has been issued.
// Setup and queue probing motion. Auto cycle-start should not start the cycle.
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Activate the probing state monitor in the stepper module.
sys_probe_state = PROBE_ACTIVE;
// Perform probing cycle. Wait here until probe is triggered or motion completes.
bit_true_atomic(sys_rt_exec_state, EXEC_CYCLE_START);
do {
protocol_execute_realtime();
if (sys.abort) { return; } // Check for system abort
} while (sys.state != STATE_IDLE);
// Probing cycle complete!
// Set state variables and error out, if the probe failed and cycle with error is enabled.
if (sys_probe_state == PROBE_ACTIVE) {
if (is_no_error) { memcpy(sys.probe_position, sys.position, sizeof(float)*N_AXIS); }
else { bit_true_atomic(sys_rt_exec_alarm, EXEC_ALARM_PROBE_FAIL); }
} else {
sys.probe_succeeded = true; // Indicate to system the probing cycle completed successfully.
}
sys_probe_state = PROBE_OFF; // Ensure probe state monitor is disabled.
protocol_execute_realtime(); // Check and execute run-time commands
if (sys.abort) { return; } // Check for system abort
// Reset the stepper and planner buffers to remove the remainder of the probe motion.
st_reset(); // Reest step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure probing motion is cleared.
plan_sync_position(); // Sync planner position to current machine position.
// TODO: Update the g-code parser code to not require this target calculation but uses a gc_sync_position() call.
// NOTE: The target[] variable updated here will be sent back and synced with the g-code parser.
system_convert_array_steps_to_mpos(target, sys.position);
#ifdef MESSAGE_PROBE_COORDINATES
// All done! Output the probe position as message.
report_probe_parameters();
#endif
}
// Perform tool length probe cycle. Requires probe switch.
// NOTE: Upon probe failure, the program will be stopped and placed into ALARM state.
uint8_t mc_probe_cycle(float *target, plan_line_data_t *pl_data, uint8_t parser_flags)
{
// TODO: Need to update this cycle so it obeys a non-auto cycle start.
if (sys.state == STATE_CHECK_MODE) { return(GC_PROBE_CHECK_MODE); }
// Finish all queued commands and empty planner buffer before starting probe cycle.
protocol_buffer_synchronize();
if (sys.abort) { return(GC_PROBE_ABORT); } // Return if system reset has been issued.
// Initialize probing control variables
uint8_t is_probe_away = bit_istrue(parser_flags,GC_PARSER_PROBE_IS_AWAY);
uint8_t is_no_error = bit_istrue(parser_flags,GC_PARSER_PROBE_IS_NO_ERROR);
sys.probe_succeeded = false; // Re-initialize probe history before beginning cycle.
probe_configure_invert_mask(is_probe_away);
// After syncing, check if probe is already triggered. If so, halt and issue alarm.
// NOTE: This probe initialization error applies to all probing cycles.
if ( probe_get_state() ) { // Check probe pin state.
system_set_exec_alarm(EXEC_ALARM_PROBE_FAIL_INITIAL);
protocol_execute_realtime();
probe_configure_invert_mask(false); // Re-initialize invert mask before returning.
return(GC_PROBE_FAIL_INIT); // Nothing else to do but bail.
}
// Setup and queue probing motion. Auto cycle-start should not start the cycle.
mc_line(target, pl_data);
// Activate the probing state monitor in the stepper module.
sys_probe_state = PROBE_ACTIVE;
// Perform probing cycle. Wait here until probe is triggered or motion completes.
system_set_exec_state_flag(EXEC_CYCLE_START);
do {
protocol_execute_realtime();
if (sys.abort) { return(GC_PROBE_ABORT); } // Check for system abort
} while (sys.state != STATE_IDLE);
// Probing cycle complete!
// Set state variables and error out, if the probe failed and cycle with error is enabled.
if (sys_probe_state == PROBE_ACTIVE) {
if (is_no_error) { memcpy(sys_probe_position, sys_position, sizeof(sys_position)); }
else { system_set_exec_alarm(EXEC_ALARM_PROBE_FAIL_CONTACT); }
} else {
sys.probe_succeeded = true; // Indicate to system the probing cycle completed successfully.
}
sys_probe_state = PROBE_OFF; // Ensure probe state monitor is disabled.
probe_configure_invert_mask(false); // Re-initialize invert mask.
protocol_execute_realtime(); // Check and execute run-time commands
// Reset the stepper and planner buffers to remove the remainder of the probe motion.
st_reset(); // Reset step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure probing motion is cleared.
plan_sync_position(); // Sync planner position to current machine position.
#ifdef MESSAGE_PROBE_COORDINATES
// All done! Output the probe position as message.
report_probe_parameters();
#endif
if (sys.probe_succeeded) { return(GC_PROBE_FOUND); } // Successful probe cycle.
else { return(GC_PROBE_FAIL_END); } // Failed to trigger probe within travel. With or without error.
}
// Execute dwell in seconds.
void mc_dwell(float seconds)
{
if (sys.state == STATE_CHECK_MODE) { return; }
protocol_buffer_synchronize();
delay_sec(seconds, DELAY_MODE_DWELL);
}
// Homes the specified cycle axes, sets the machine position, and performs a pull-off motion after
// completing. Homing is a special motion case, which involves rapid uncontrolled stops to locate
// the trigger point of the limit switches. The rapid stops are handled by a system level axis lock
// mask, which prevents the stepper algorithm from executing step pulses. Homing motions typically
// circumvent the processes for executing motions in normal operation.
// NOTE: Only the abort runtime command can interrupt this process.
void limits_go_home(uint8_t cycle_mask)
{
if (sys.abort) { return; } // Block if system reset has been issued.
// Initialize homing in search mode to quickly engage the specified cycle_mask limit switches.
bool approach = true;
float homing_rate = settings.homing_seek_rate;
uint8_t invert_pin, idx;
uint8_t n_cycle = (2*N_HOMING_LOCATE_CYCLE+1); ///***5
float target[N_AXIS];
uint8_t limit_pin[N_AXIS], step_pin[N_AXIS];
float max_travel = 0.0;
for (idx=0; idx<N_AXIS; idx++) {
// Initialize limit and step pin masks
limit_pin[idx] = get_limit_pin_mask(idx); ///////****get the Pin of limit min x, y ,z , Limit OK
step_pin[idx] = get_step_pin_mask(idx); ///////****get the Pin of limit min x, y ,z now I let it 0, 1, 2
// Determine travel distance to the furthest homing switch based on user max travel settings.
// NOTE: settings.max_travel[] is stored as a negative value.
if (max_travel > settings.max_travel[idx]) { max_travel = settings.max_travel[idx]; }
}
max_travel *= -HOMING_AXIS_SEARCH_SCALAR; // Ensure homing switches engaged by over-estimating max travel.
plan_reset(); // Reset planner buffer to zero planner current position and to clear previous motions.
do {
// Initialize invert_pin boolean based on approach and invert pin user setting.
if (bit_isfalse(settings.flags,BITFLAG_INVERT_LIMIT_PINS)) { invert_pin = approach; }
else { invert_pin = !approach; }
// Initialize and declare variables needed for homing routine.
uint8_t n_active_axis = 0;
uint8_t axislock = 0;
for (idx=0; idx<N_AXIS; idx++) {
// Set target location for active axes and setup computation for homing rate.
if (bit_istrue(cycle_mask,bit(idx))) {
n_active_axis++;
if (!approach) { target[idx] = -max_travel; }
else { target[idx] = max_travel; }
} else {
target[idx] = 0.0;
}
// Set target direction based on cycle mask
if (bit_istrue(settings.homing_dir_mask,bit(idx))) { target[idx] = -target[idx]; }
// Apply axislock to the step port pins active in this cycle.
if (bit_istrue(cycle_mask,bit(idx))) { axislock |= step_pin[idx]; }
}
homing_rate *= sqrt(n_active_axis); // [sqrt(N_AXIS)] Adjust so individual axes all move at homing rate.
sys.homing_axis_lock = axislock;
// Perform homing cycle. Planner buffer should be empty, as required to initiate the homing cycle.
uint8_t limit_state;
#ifdef USE_LINE_NUMBERS
plan_buffer_line(target, homing_rate, false, HOMING_CYCLE_LINE_NUMBER); // Bypass mc_line(). Directly plan homing motion.
#else
plan_buffer_line(target, homing_rate, false); // Bypass mc_line(). Directly plan homing motion.
#endif
st_prep_buffer(); // Prep and fill segment buffer from newly planned block.
st_wake_up(); // Initiate motion
do {
// Check limit state. Lock out cycle axes when they change.
/////////////////########################################***********
#if MotherBoard==3 /////**MB==3
#ifdef limit_int_style
limit_state = LIMIT_PIN;
if (invert_pin) { limit_state ^= LIMIT_MASK; }
#else
//************Get Limit Pin State. PiBot get limit/endstop mask same with the step mask.
#if LIMIT_MAX_OPEN
if(isXMinEndstopHit()) { limit_state^= MASK(X_LIMIT_BIT);} ////***read X_endstop then write into limite_state
if(isYMinEndstopHit()) { limit_state^= MASK(Y_LIMIT_BIT);}
if(isZMinEndstopHit()) { limit_state^= MASK(Z_LIMIT_BIT);} ////*****add MAX limit
if(isXMaxEndstopHit()) { limit_state^= MASK(X_LIMIT_MAX_BIT);} ////***read X_endstop then write into limite_state
if(isYMaxEndstopHit()) { limit_state^= MASK(Y_LIMIT_MAX_BIT);}
if(isZMaxEndstopHit()) { limit_state^= MASK(Z_LIMIT_MAX_BIT);} ////*****add MAX limit
#else
if(isXMinEndstopHit()) { limit_state^= MASK(X_MASK);} ////***read X_endstop then write into limite_state
if(isYMinEndstopHit()) { limit_state^= MASK(Y_MASK);}
if(isZMinEndstopHit()) { limit_state^= MASK(Z_MASK);} ////*****add MAX limit
#endif
#endif
#else /////**MB!=3 ////////#################################################
limit_state = LIMIT_PIN;
if (invert_pin) { limit_state ^= LIMIT_MASK; }
#endif /////**MB==3
/////////////////////////////#####################################
for (idx=0; idx<N_AXIS; idx++) {
if (axislock & step_pin[idx]) {
if (limit_state & limit_pin[idx]) { axislock &= ~(step_pin[idx]); }
}
}
sys.homing_axis_lock = axislock;
st_prep_buffer(); // Check and prep segment buffer. NOTE: Should take no longer than 200us.
// Check only for user reset. No time to run protocol_execute_runtime() in this loop.
if (sys.execute & EXEC_RESET) { protocol_execute_runtime(); return; }
} while (STEP_MASK & axislock);
st_reset(); // Immediately force kill steppers and reset step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure homing motion is cleared.
delay_ms(settings.homing_debounce_delay); // Delay to allow transient dynamics to dissipate.
// Reverse direction and reset homing rate for locate cycle(s).
homing_rate = settings.homing_feed_rate;
approach = !approach;
} while (n_cycle-- > 0);
// The active cycle axes should now be homed and machine limits have been located. By
// default, grbl defines machine space as all negative, as do most CNCs. Since limit switches
// can be on either side of an axes, check and set axes machine zero appropriately. Also,
// set up pull-off maneuver from axes limit switches that have been homed. This provides
// some initial clearance off the switches and should also help prevent them from falsely
// triggering when hard limits are enabled or when more than one axes shares a limit pin.
for (idx=0; idx<N_AXIS; idx++) {
// Set up pull off targets and machine positions for limit switches homed in the negative
// direction, rather than the traditional positive. Leave non-homed positions as zero and
// do not move them.
// NOTE: settings.max_travel[] is stored as a negative value.
if (cycle_mask & bit(idx)) {
#ifdef HOMING_FORCE_SET_ORIGIN
sys.position[idx] = 0; // Set axis homed location as axis origin
target[idx] = settings.homing_pulloff;
if ( bit_isfalse(settings.homing_dir_mask,bit(idx)) ) { target[idx] = -target[idx]; }
#else
if ( bit_istrue(settings.homing_dir_mask,bit(idx)) ) {
target[idx] = settings.homing_pulloff+settings.max_travel[idx];
sys.position[idx] = lround(settings.max_travel[idx]*settings.steps_per_mm[idx]);
} else {
target[idx] = -settings.homing_pulloff;
sys.position[idx] = 0;
}
#endif
} else { // Non-active cycle axis. Set target to not move during pull-off.
target[idx] = (float)sys.position[idx]/settings.steps_per_mm[idx];
}
}
plan_sync_position(); // Sync planner position to current machine position for pull-off move.
#ifdef USE_LINE_NUMBERS
plan_buffer_line(target, settings.homing_seek_rate, false, HOMING_CYCLE_LINE_NUMBER); // Bypass mc_line(). Directly plan motion.
#else
plan_buffer_line(target, settings.homing_seek_rate, false); // Bypass mc_line(). Directly plan motion.
#endif
// Initiate pull-off using main motion control routines.
// TODO : Clean up state routines so that this motion still shows homing state.
sys.state = STATE_QUEUED;
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
protocol_execute_runtime();
protocol_buffer_synchronize(); // Complete pull-off motion.
// Set system state to homing before returning.
sys.state = STATE_HOMING;
}
void coolant_run(uint8_t mode)
{
if (sys.state == STATE_CHECK_MODE) { return; }
protocol_buffer_synchronize(); // Ensure coolant turns on when specified in program.
coolant_set_state(mode);
}
void mc_probe_cycle(float *target, float feed_rate, uint8_t invert_feed_rate)
#endif
{
// TODO: Need to update this cycle so it obeys a non-auto cycle start.
if (sys.state == STATE_CHECK_MODE) { return; }
// Finish all queued commands and empty planner buffer before starting probe cycle.
protocol_buffer_synchronize();
uint8_t auto_start_state = sys.auto_start; // Store run state
// After syncing, check if probe is already triggered. If so, halt and issue alarm.
if (probe_get_state()) {
bit_true_atomic(sys.execute, EXEC_CRIT_EVENT);
protocol_execute_runtime();
}
if (sys.abort) { return; } // Return if system reset has been issued.
// Setup and queue probing motion. Auto cycle-start should not start the cycle.
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Activate the probing monitor in the stepper module.
sys.probe_state = PROBE_ACTIVE;
// Perform probing cycle. Wait here until probe is triggered or motion completes.
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
do {
protocol_execute_runtime();
if (sys.abort) { return; } // Check for system abort
} while ((sys.state != STATE_IDLE) && (sys.state != STATE_QUEUED));
// Probing motion complete. If the probe has not been triggered, error out.
if (sys.probe_state == PROBE_ACTIVE) { bit_true_atomic(sys.execute, EXEC_CRIT_EVENT); }
protocol_execute_runtime(); // Check and execute run-time commands
if (sys.abort) { return; } // Check for system abort
// Reset the stepper and planner buffers to remove the remainder of the probe motion.
st_reset(); // Reest step segment buffer.
plan_reset(); // Reset planner buffer. Zero planner positions. Ensure probing motion is cleared.
plan_sync_position(); // Sync planner position to current machine position.
// Pull-off triggered probe to the trigger location since we had to decelerate a little beyond
// it to stop the machine in a controlled manner.
uint8_t idx;
for(idx=0; idx<N_AXIS; idx++){
// NOTE: The target[] variable updated here will be sent back and synced with the g-code parser.
target[idx] = (float)sys.probe_position[idx]/settings.steps_per_deg[idx];
}
#ifdef USE_LINE_NUMBERS
mc_line(target, feed_rate, invert_feed_rate, line_number);
#else
mc_line(target, feed_rate, invert_feed_rate);
#endif
// Execute pull-off motion and wait until it completes.
bit_true_atomic(sys.execute, EXEC_CYCLE_START);
protocol_buffer_synchronize();
if (sys.abort) { return; } // Return if system reset has been issued.
sys.auto_start = auto_start_state; // Restore run state before returning
#ifdef MESSAGE_PROBE_COORDINATES
// All done! Output the probe position as message.
report_probe_parameters();
#endif
}
void spindle_run(uint8_t state, float rpm)
{
if (sys.state == STATE_CHECK_MODE) { return; }
protocol_buffer_synchronize(); // Empty planner buffer to ensure spindle is set when programmed.
spindle_set_state(state, rpm);
}
// Executes one line of 0-terminated G-Code. The line is assumed to contain only uppercase
// characters and signed floating point values (no whitespace). Comments and block delete
// characters have been removed. In this function, all units and positions are converted and
// exported to grbl's internal functions in terms of (mm, mm/min) and absolute machine
// coordinates, respectively.
uint8_t gc_execute_line(char *line)
{
/* -------------------------------------------------------------------------------------
STEP 1: Initialize parser block struct and copy current g-code state modes. The parser
updates these modes and commands as the block line is parser and will only be used and
executed after successful error-checking. The parser block struct also contains a block
values struct, word tracking variables, and a non-modal commands tracker for the new
block. This struct contains all of the necessary information to execute the block. */
memset(&gc_block, 0, sizeof(gc_block)); // Initialize the parser block struct.
memcpy(&gc_block.modal,&gc_state.modal,sizeof(gc_modal_t)); // Copy current modes
uint8_t axis_command = AXIS_COMMAND_NONE;
uint8_t axis_0, axis_1, axis_linear;
uint8_t coord_select = 0; // Tracks G10 P coordinate selection for execution
float coordinate_data[N_AXIS]; // Multi-use variable to store coordinate data for execution
float parameter_data[N_AXIS]; // Multi-use variable to store parameter data for execution
// Initialize bitflag tracking variables for axis indices compatible operations.
uint8_t axis_words = 0; // XYZ tracking
// Initialize command and value words variables. Tracks words contained in this block.
uint16_t command_words = 0; // G and M command words. Also used for modal group violations.
uint16_t value_words = 0; // Value words.
/* -------------------------------------------------------------------------------------
STEP 2: Import all g-code words in the block line. A g-code word is a letter followed by
a number, which can either be a 'G'/'M' command or sets/assigns a command value. Also,
perform initial error-checks for command word modal group violations, for any repeated
words, and for negative values set for the value words F, N, P, T, and S. */
uint8_t word_bit; // Bit-value for assigning tracking variables
uint8_t char_counter = 0;
char letter;
float value;
uint8_t int_value = 0;
uint8_t mantissa = 0; // NOTE: For mantissa values > 255, variable type must be changed to uint16_t.
while (line[char_counter] != 0) { // Loop until no more g-code words in line.
// Import the next g-code word, expecting a letter followed by a value. Otherwise, error out.
letter = line[char_counter];
if((letter < 'A') || (letter > 'Z')) { FAIL(STATUS_EXPECTED_COMMAND_LETTER); } // [Expected word letter]
char_counter++;
if (!read_float(line, &char_counter, &value)) { FAIL(STATUS_BAD_NUMBER_FORMAT); } // [Expected word value]
// Convert values to smaller uint8 significand and mantissa values for parsing this word.
// NOTE: Mantissa is multiplied by 100 to catch non-integer command values. This is more
// accurate than the NIST gcode requirement of x10 when used for commands, but not quite
// accurate enough for value words that require integers to within 0.0001. This should be
// a good enough comprimise and catch most all non-integer errors. To make it compliant,
// we would simply need to change the mantissa to int16, but this add compiled flash space.
// Maybe update this later.
int_value = trunc(value);
mantissa = round(100*(value - int_value)); // Compute mantissa for Gxx.x commands.
// NOTE: Rounding must be used to catch small floating point errors.
// Check if the g-code word is supported or errors due to modal group violations or has
// been repeated in the g-code block. If ok, update the command or record its value.
switch(letter) {
/* 'G' and 'M' Command Words: Parse commands and check for modal group violations.
NOTE: Modal group numbers are defined in Table 4 of NIST RS274-NGC v3, pg.20 */
case 'G':
// Determine 'G' command and its modal group
switch(int_value) {
case 1:
if (axis_command) { FAIL(STATUS_GCODE_AXIS_COMMAND_CONFLICT); } // [Axis word/command conflict]
axis_command = AXIS_COMMAND_MOTION_MODE;
gc_block.modal.motion = MOTION_MODE_LINEAR;
word_bit = MODAL_GROUP_G1;
break;
default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported G command]
}
if (mantissa > 0) { FAIL(STATUS_GCODE_COMMAND_VALUE_NOT_INTEGER); } // [Unsupported or invalid Gxx.x command]
// Check for more than one command per modal group violations in the current block
// NOTE: Variable 'word_bit' is always assigned, if the command is valid.
if ( bit_istrue(command_words,bit(word_bit)) ) { FAIL(STATUS_GCODE_MODAL_GROUP_VIOLATION); }
command_words |= bit(word_bit);
break;
case 'M':
// Determine 'M' command and its modal group
if (mantissa > 0) { FAIL(STATUS_GCODE_COMMAND_VALUE_NOT_INTEGER); } // [No Mxx.x commands]
switch(int_value) {
case 0: case 2:
word_bit = MODAL_GROUP_M4;
switch(int_value) {
case 0: gc_block.modal.program_flow = PROGRAM_FLOW_PAUSED; break; // Program pause
case 2: gc_block.modal.program_flow = PROGRAM_FLOW_COMPLETED; break; // Program end and reset
}
break;
case 17: gc_block.modal.motor = MOTOR_ENABLE; break;
case 18: gc_block.modal.motor = MOTOR_DISABLE; break;
case 50: gc_block.modal.ldr = LDR_READ; break;
case 70: gc_block.modal.laser = LASER_DISABLE; break;
case 71: gc_block.modal.laser = LASER_ENABLE; break;
default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); // [Unsupported M command]
}
// Check for more than one command per modal group violations in the current block
// NOTE: Variable 'word_bit' is always assigned, if the command is valid.
if ( bit_istrue(command_words,bit(word_bit)) ) { FAIL(STATUS_GCODE_MODAL_GROUP_VIOLATION); }
command_words |= bit(word_bit);
break;
// NOTE: All remaining letters assign values.
default:
/* Non-Command Words: This initial parsing phase only checks for repeats of the remaining
legal g-code words and stores their value. Error-checking is performed later since some
words (I,J,K,L,P,R) have multiple connotations and/or depend on the issued commands. */
switch(letter){
case 'F': word_bit = WORD_F; gc_block.values.f = value; break;
case 'T': word_bit = WORD_T; gc_block.values.t = int_value; break; // gc.values.t = int_value;
case 'X': word_bit = WORD_X; gc_block.values.xyz[X_AXIS] = value; axis_words |= (1<<X_AXIS); break;
/*case 'Y': word_bit = WORD_Y; gc_block.values.xyz[Y_AXIS] = value; axis_words |= (1<<Y_AXIS); break;
case 'Z': word_bit = WORD_Z; gc_block.values.xyz[Z_AXIS] = value; axis_words |= (1<<Z_AXIS); break;*/
default: FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND);
}
// NOTE: Variable 'word_bit' is always assigned, if the non-command letter is valid.
if (bit_istrue(value_words,bit(word_bit))) { FAIL(STATUS_GCODE_WORD_REPEATED); } // [Word repeated]
// Check for invalid negative values for words F, N, P, T, and S.
// NOTE: Negative value check is done here simply for code-efficiency.
if ( bit(word_bit) & (bit(WORD_F)|bit(WORD_N)|bit(WORD_P)|bit(WORD_T)|bit(WORD_S)) ) {
if (value < 0.0) { FAIL(STATUS_NEGATIVE_VALUE); } // [Word value cannot be negative]
}
value_words |= bit(word_bit); // Flag to indicate parameter assigned.
}
}
// Parsing complete!
/* -------------------------------------------------------------------------------------
STEP 3: Error-check all commands and values passed in this block. This step ensures all of
the commands are valid for execution and follows the NIST standard as closely as possible.
If an error is found, all commands and values in this block are dumped and will not update
the active system g-code modes. If the block is ok, the active system g-code modes will be
updated based on the commands of this block, and signal for it to be executed.
Also, we have to pre-convert all of the values passed based on the modes set by the parsed
block. There are a number of error-checks that require target information that can only be
accurately calculated if we convert these values in conjunction with the error-checking.
This relegates the next execution step as only updating the system g-code modes and
performing the programmed actions in order. The execution step should not require any
conversion calculations and would only require minimal checks necessary to execute.
*/
/* NOTE: At this point, the g-code block has been parsed and the block line can be freed.
NOTE: It's also possible, at some future point, to break up STEP 2, to allow piece-wise
parsing of the block on a per-word basis, rather than the entire block. This could remove
the need for maintaining a large string variable for the entire block and free up some memory.
To do this, this would simply need to retain all of the data in STEP 1, such as the new block
data struct, the modal group and value bitflag tracking variables, and axis array indices
compatible variables. This data contains all of the information necessary to error-check the
new g-code block when the EOL character is received. However, this would break Grbl's startup
lines in how it currently works and would require some refactoring to make it compatible.
*/
// [0. Non-specific/common error-checks and miscellaneous setup]:
// Determine implicit axis command conditions. Axis words have been passed, but no explicit axis
// command has been sent. If so, set axis command to current motion mode.
if (axis_words) {
if (!axis_command) { axis_command = AXIS_COMMAND_MOTION_MODE; } // Assign implicit motion-mode
}
// Check for valid line number N value.
if (bit_istrue(value_words,bit(WORD_N))) {
// Line number value cannot be less than zero (done) or greater than max line number.
if (gc_block.values.n > MAX_LINE_NUMBER) { FAIL(STATUS_GCODE_INVALID_LINE_NUMBER); } // [Exceeds max line number]
}
// bit_false(value_words,bit(WORD_N)); // NOTE: Single-meaning value word. Set at end of error-checking.
// Track for unused words at the end of error-checking.
// NOTE: Single-meaning value words are removed all at once at the end of error-checking, because
// they are always used when present. This was done to save a few bytes of flash. For clarity, the
// single-meaning value words may be removed as they are used. Also, axis words are treated in the
// same way. If there is an explicit/implicit axis command, XYZ words are always used and are
// are removed at the end of error-checking.
// [1. Comments ]: MSG's NOT SUPPORTED. Comment handling performed by protocol.
// [2. Set feed rate mode ]: G93 F word missing with G1,G2/3 active, implicitly or explicitly. Feed rate
// is not defined after switching to G94 from G93.
if (gc_block.modal.feed_rate == FEED_RATE_MODE_INVERSE_TIME) { // = G93
// NOTE: G38 can also operate in inverse time, but is undefined as an error. Missing F word check added here.
if (axis_command == AXIS_COMMAND_MOTION_MODE) {
if ((gc_block.modal.motion != MOTION_MODE_NONE) || (gc_block.modal.motion != MOTION_MODE_SEEK)) {
if (bit_isfalse(value_words,bit(WORD_F))) { FAIL(STATUS_GCODE_UNDEFINED_FEED_RATE); } // [F word missing]
}
}
// NOTE: It seems redundant to check for an F word to be passed after switching from G94 to G93. We would
// accomplish the exact same thing if the feed rate value is always reset to zero and undefined after each
// inverse time block, since the commands that use this value already perform undefined checks. This would
// also allow other commands, following this switch, to execute and not error out needlessly. This code is
// combined with the above feed rate mode and the below set feed rate error-checking.
// [3. Set feed rate ]: F is negative (done.)
// - In inverse time mode: Always implicitly zero the feed rate value before and after block completion.
// NOTE: If in G93 mode or switched into it from G94, just keep F value as initialized zero or passed F word
// value in the block. If no F word is passed with a motion command that requires a feed rate, this will error
// out in the motion modes error-checking. However, if no F word is passed with NO motion command that requires
// a feed rate, we simply move on and the state feed rate value gets updated to zero and remains undefined.
} else { // = G94
// - In units per mm mode: If F word passed, ensure value is in mm/min, otherwise push last state value.
if (gc_state.modal.feed_rate == FEED_RATE_MODE_UNITS_PER_MIN) { // Last state is also G94
if (bit_istrue(value_words,bit(WORD_F))) {
if (gc_block.modal.units == UNITS_MODE_INCHES) { gc_block.values.f *= MM_PER_INCH; }
} else {
gc_block.values.f = gc_state.feed_rate/60; // Push last state feed rate. Convert deg/min to deg/sec
}
} // Else, switching to G94 from G93, so don't push last state feed rate. Its undefined or the passed F word value.
}
// bit_false(value_words,bit(WORD_F)); // NOTE: Single-meaning value word. Set at end of error-checking.
// [4. Set spindle speed ]: S is negative (done.)
if (bit_isfalse(value_words,bit(WORD_S))) { gc_block.values.s = gc_state.spindle_speed; }
// bit_false(value_words,bit(WORD_S)); // NOTE: Single-meaning value word. Set at end of error-checking.
// [5. Select tool ]: NOT SUPPORTED. Only tracks value. T is negative (done.) Not an integer. Greater than max tool value.
// bit_false(value_words,bit(WORD_T)); // NOTE: Single-meaning value word. Set at end of error-checking.
// [6. Change tool ]: N/A
// [7. Spindle control ]: N/A
// [8. Coolant control ]: N/A
// [9. Enable/disable feed rate or spindle overrides ]: NOT SUPPORTED.
// [10. Dwell ]: P value missing. P is negative (done.) NOTE: See below.
if (gc_block.non_modal_command == NON_MODAL_DWELL) {
if (bit_isfalse(value_words,bit(WORD_P))) { FAIL(STATUS_GCODE_VALUE_WORD_MISSING); } // [P word missing]
bit_false(value_words,bit(WORD_P));
}
// [11. Set active plane ]: N/A
switch (gc_block.modal.plane_select) {
case PLANE_SELECT_XY:
axis_0 = X_AXIS;
axis_1 = Y_AXIS;
axis_linear = Z_AXIS;
break;
case PLANE_SELECT_ZX:
axis_0 = Z_AXIS;
axis_1 = X_AXIS;
axis_linear = Y_AXIS;
break;
default: // case PLANE_SELECT_YZ:
axis_0 = Y_AXIS;
axis_1 = Z_AXIS;
axis_linear = X_AXIS;
}
// [12. Set length units ]: N/A
// Pre-convert XYZ coordinate values to millimeters, if applicable.
uint8_t idx;
if (gc_block.modal.units == UNITS_MODE_INCHES) {
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
if (bit_istrue(axis_words,bit(idx)) ) {
gc_block.values.xyz[idx] *= MM_PER_INCH;
}
}
}
// [13. Cutter radius compensation ]: NOT SUPPORTED. Error, if G53 is active.
// [14. Cutter length compensation ]: G43 NOT SUPPORTED, but G43.1 and G49 are.
// [G43.1 Errors]: Motion command in same line.
// NOTE: Although not explicitly stated so, G43.1 should be applied to only one valid
// axis that is configured (in config.h). There should be an error if the configured axis
// is absent or if any of the other axis words are present.
if (axis_command == AXIS_COMMAND_TOOL_LENGTH_OFFSET ) { // Indicates called in block.
if (gc_block.modal.tool_length == TOOL_LENGTH_OFFSET_ENABLE_DYNAMIC) {
if (axis_words ^ (1<<TOOL_LENGTH_OFFSET_AXIS)) { FAIL(STATUS_GCODE_G43_DYNAMIC_AXIS_ERROR); }
}
}
// [15. Coordinate system selection ]: *N/A. Error, if cutter radius comp is active.
// TODO: An EEPROM read of the coordinate data may require a buffer sync when the cycle
// is active. The read pauses the processor temporarily and may cause a rare crash. For
// future versions on processors with enough memory, all coordinate data should be stored
// in memory and written to EEPROM only when there is not a cycle active.
memcpy(coordinate_data,gc_state.coord_system,sizeof(gc_state.coord_system));
if ( bit_istrue(command_words,bit(MODAL_GROUP_G12)) ) { // Check if called in block
if (gc_block.modal.coord_select > N_COORDINATE_SYSTEM) { FAIL(STATUS_GCODE_UNSUPPORTED_COORD_SYS); } // [Greater than N sys]
if (gc_state.modal.coord_select != gc_block.modal.coord_select) {
if (!(settings_read_coord_data(gc_block.modal.coord_select,coordinate_data))) { FAIL(STATUS_SETTING_READ_FAIL); }
}
}
// [16. Set path control mode ]: NOT SUPPORTED.
// [17. Set distance mode ]: N/A. G90.1 and G91.1 NOT SUPPORTED.
// [18. Set retract mode ]: NOT SUPPORTED.
// [19. Remaining non-modal actions ]: Check go to predefined position, set G10, or set axis offsets.
// NOTE: We need to separate the non-modal commands that are axis word-using (G10/G28/G30/G92), as these
// commands all treat axis words differently. G10 as absolute offsets or computes current position as
// the axis value, G92 similarly to G10 L20, and G28/30 as an intermediate target position that observes
// all the current coordinate system and G92 offsets.
switch (gc_block.non_modal_command) {
case NON_MODAL_SET_COORDINATE_DATA:
// [G10 Errors]: L missing and is not 2 or 20. P word missing. (Negative P value done.)
// [G10 L2 Errors]: R word NOT SUPPORTED. P value not 0 to nCoordSys(max 9). Axis words missing.
// [G10 L20 Errors]: P must be 0 to nCoordSys(max 9). Axis words missing.
if (!axis_words) { FAIL(STATUS_GCODE_NO_AXIS_WORDS) }; // [No axis words]
if (bit_isfalse(value_words,((1<<WORD_P)|(1<<WORD_L)))) { FAIL(STATUS_GCODE_VALUE_WORD_MISSING); } // [P/L word missing]
coord_select = trunc(gc_block.values.p); // Convert p value to int.
if (coord_select > N_COORDINATE_SYSTEM) { FAIL(STATUS_GCODE_UNSUPPORTED_COORD_SYS); } // [Greater than N sys]
if (gc_block.values.l != 20) {
if (gc_block.values.l == 2) {
if (bit_istrue(value_words,bit(WORD_R))) { FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); } // [G10 L2 R not supported]
} else { FAIL(STATUS_GCODE_UNSUPPORTED_COMMAND); } // [Unsupported L]
}
bit_false(value_words,(bit(WORD_L)|bit(WORD_P)));
// Determine coordinate system to change and try to load from EEPROM.
if (coord_select > 0) { coord_select--; } // Adjust P1-P6 index to EEPROM coordinate data indexing.
else { coord_select = gc_block.modal.coord_select; } // Index P0 as the active coordinate system
if (!settings_read_coord_data(coord_select,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); } // [EEPROM read fail]
// Pre-calculate the coordinate data changes. NOTE: Uses parameter_data since coordinate_data may be in use by G54-59.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
// Update axes defined only in block. Always in machine coordinates. Can change non-active system.
if (bit_istrue(axis_words,bit(idx)) ) {
if (gc_block.values.l == 20) {
// L20: Update coordinate system axis at current position (with modifiers) with programmed value
parameter_data[idx] = gc_state.position[idx]-gc_state.coord_offset[idx]-gc_block.values.xyz[idx];
if (idx == TOOL_LENGTH_OFFSET_AXIS) { parameter_data[idx] -= gc_state.tool_length_offset; }
} else {
// L2: Update coordinate system axis to programmed value.
parameter_data[idx] = gc_block.values.xyz[idx];
}
}
}
break;
case NON_MODAL_SET_COORDINATE_OFFSET:
// [G92 Errors]: No axis words.
if (!axis_words) { FAIL(STATUS_GCODE_NO_AXIS_WORDS); } // [No axis words]
// Update axes defined only in block. Offsets current system to defined value. Does not update when
// active coordinate system is selected, but is still active unless G92.1 disables it.
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used.
if (bit_istrue(axis_words,bit(idx)) ) {
gc_block.values.xyz[idx] = gc_state.position[idx]-coordinate_data[idx]-gc_block.values.xyz[idx];
if (idx == TOOL_LENGTH_OFFSET_AXIS) { gc_block.values.xyz[idx] -= gc_state.tool_length_offset; }
} else {
gc_block.values.xyz[idx] = gc_state.coord_offset[idx];
}
}
break;
default:
// At this point, the rest of the explicit axis commands treat the axis values as the traditional
// target position with the coordinate system offsets, G92 offsets, absolute override, and distance
// modes applied. This includes the motion mode commands. We can now pre-compute the target position.
// NOTE: Tool offsets may be appended to these conversions when/if this feature is added.
if (axis_command != AXIS_COMMAND_TOOL_LENGTH_OFFSET ) { // TLO block any axis command.
if (axis_words) {
for (idx=0; idx<N_AXIS; idx++) { // Axes indices are consistent, so loop may be used to save flash space.
if ( bit_isfalse(axis_words,bit(idx)) ) {
gc_block.values.xyz[idx] = gc_state.position[idx]; // No axis word in block. Keep same axis position.
} else {
// Update specified value according to distance mode or ignore if absolute override is active.
// NOTE: G53 is never active with G28/30 since they are in the same modal group.
if (gc_block.non_modal_command != NON_MODAL_ABSOLUTE_OVERRIDE) {
// Apply coordinate offsets based on distance mode.
if (gc_block.modal.distance == DISTANCE_MODE_ABSOLUTE) {
gc_block.values.xyz[idx] += coordinate_data[idx] + gc_state.coord_offset[idx];
if (idx == TOOL_LENGTH_OFFSET_AXIS) { gc_block.values.xyz[idx] += gc_state.tool_length_offset; }
} else { // Incremental mode
gc_block.values.xyz[idx] += gc_state.position[idx];
}
}
}
}
}
}
// Check remaining non-modal commands for errors.
switch (gc_block.non_modal_command) {
case NON_MODAL_GO_HOME_0:
// [G28 Errors]: Cutter compensation is enabled.
// Retreive G28 go-home position data (in machine coordinates) from EEPROM
if (!axis_words) { axis_command = AXIS_COMMAND_NONE; } // Set to none if no intermediate motion.
if (!settings_read_coord_data(SETTING_INDEX_G28,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); }
break;
case NON_MODAL_GO_HOME_1:
// [G30 Errors]: Cutter compensation is enabled.
// Retreive G30 go-home position data (in machine coordinates) from EEPROM
if (!axis_words) { axis_command = AXIS_COMMAND_NONE; } // Set to none if no intermediate motion.
if (!settings_read_coord_data(SETTING_INDEX_G30,parameter_data)) { FAIL(STATUS_SETTING_READ_FAIL); }
break;
case NON_MODAL_SET_HOME_0: case NON_MODAL_SET_HOME_1:
// [G28.1/30.1 Errors]: Cutter compensation is enabled.
// NOTE: If axis words are passed here, they are interpreted as an implicit motion mode.
break;
case NON_MODAL_RESET_COORDINATE_OFFSET:
// NOTE: If axis words are passed here, they are interpreted as an implicit motion mode.
break;
case NON_MODAL_ABSOLUTE_OVERRIDE:
// [G53 Errors]: G0 and G1 are not active. Cutter compensation is enabled.
// NOTE: All explicit axis word commands are in this modal group. So no implicit check necessary.
if (!(gc_block.modal.motion == MOTION_MODE_SEEK || gc_block.modal.motion == MOTION_MODE_LINEAR)) {
FAIL(STATUS_GCODE_G53_INVALID_MOTION_MODE); // [G53 G0/1 not active]
}
break;
}
}
// [20. Motion modes ]:
if (gc_block.modal.motion == MOTION_MODE_NONE) {
// [G80 Errors]: Axis word exist and are not used by a non-modal command.
if ((axis_words) && (axis_command != AXIS_COMMAND_NON_MODAL)) {
FAIL(STATUS_GCODE_AXIS_WORDS_EXIST); // [No axis words allowed]
}
// Check remaining motion modes, if axis word are implicit (exist and not used by G10/28/30/92), or
// was explicitly commanded in the g-code block.
} else if ( axis_command == AXIS_COMMAND_MOTION_MODE ) {
if (gc_block.modal.motion == MOTION_MODE_SEEK) {
// [G0 Errors]: Axis letter not configured or without real value (done.)
// Axis words are optional. If missing, set axis command flag to ignore execution.
if (!axis_words) { axis_command = AXIS_COMMAND_NONE; }
// All remaining motion modes (all but G0 and G80), require a valid feed rate value. In units per mm mode,
// the value must be positive. In inverse time mode, a positive value must be passed with each block.
} else {
// Check if feed rate is defined for the motion modes that require it.
if (gc_block.values.f == 0.0) { FAIL(STATUS_GCODE_UNDEFINED_FEED_RATE); } // [Feed rate undefined]
switch (gc_block.modal.motion) {
case MOTION_MODE_LINEAR:
// [G1 Errors]: Feed rate undefined. Axis letter not configured or without real value.
// Axis words are optional. If missing, set axis command flag to ignore execution.
if (!axis_words) { axis_command = AXIS_COMMAND_NONE; }
break;
case MOTION_MODE_PROBE:
// [G38 Errors]: Target is same current. No axis words. Cutter compensation is enabled. Feed rate
// is undefined. Probe is triggered. NOTE: Probe check moved to probe cycle. Instead of returning
// an error, it issues an alarm to prevent further motion to the probe. It's also done there to
// allow the planner buffer to empty and move off the probe trigger before another probing cycle.
if (!axis_words) { FAIL(STATUS_GCODE_NO_AXIS_WORDS); } // [No axis words]
if (gc_check_same_position(gc_state.position, gc_block.values.xyz)) { FAIL(STATUS_GCODE_INVALID_TARGET); } // [Invalid target]
break;
}
}
}
// [21. Program flow ]: No error checks required.
// [0. Non-specific error-checks]: Complete unused value words check,
// radius mode, or axis words that aren't used in the block.
bit_false(value_words,(bit(WORD_N)|bit(WORD_F)|bit(WORD_S)|bit(WORD_T))); // Remove single-meaning value words.
if (axis_command) { bit_false(value_words,(bit(WORD_X)|bit(WORD_Y)|bit(WORD_Z))); } // Remove axis words.
if (value_words) { FAIL(STATUS_GCODE_UNUSED_WORDS); } // [Unused words]
/* -------------------------------------------------------------------------------------
STEP 4: EXECUTE!!
Assumes that all error-checking has been completed and no failure modes exist. We just
need to update the state and execute the block according to the order-of-execution.
*/
// [1. Comments feedback ]: NOT SUPPORTED
// [2. Set feed rate mode ]:
gc_state.modal.feed_rate = gc_block.modal.feed_rate;
// [3. Set feed rate ]:
gc_state.feed_rate = gc_block.values.f*60; // Always copy this value. See feed rate error-checking. Convert deg/sec to deg/min
/*// [4. Set spindle speed ]:
if (gc_state.spindle_speed != gc_block.values.s) {
gc_state.spindle_speed = gc_block.values.s;
// Update running spindle only if not in check mode and not already enabled.
if (gc_state.modal.spindle != SPINDLE_DISABLE) { spindle_run(gc_state.modal.spindle, gc_state.spindle_speed); }
}*/
// [5. Select tool ]: NOT SUPPORTED. Only tracks tool value.
gc_state.tool = gc_block.values.t;
// [6. Change tool ]: NOT SUPPORTED
// [7. Spindle control ]: NOT SUPPORTED
// [8. Coolant control ]: NOT SUPPORTED
// [9. Enable/disable feed rate or spindle overrides ]: NOT SUPPORTED
// [10. Dwell ]:
if (gc_block.non_modal_command == NON_MODAL_DWELL) { mc_dwell(gc_block.values.p); }
// [11. Set active plane ]:
gc_state.modal.plane_select = gc_block.modal.plane_select;
// [12. Set length units ]: NOT SUPPORTED
// [13. Cutter radius compensation ]: NOT SUPPORTED
// [14. Cutter length compensation ]: G43.1 and G49 supported. G43 NOT SUPPORTED.
// NOTE: If G43 were supported, its operation wouldn't be any different from G43.1 in terms
// of execution. The error-checking step would simply load the offset value into the correct
// axis of the block XYZ value array.
if (axis_command == AXIS_COMMAND_TOOL_LENGTH_OFFSET ) { // Indicates a change.
gc_state.modal.tool_length = gc_block.modal.tool_length;
if (gc_state.modal.tool_length == TOOL_LENGTH_OFFSET_ENABLE_DYNAMIC) { // G43.1
gc_state.tool_length_offset = gc_block.values.xyz[TOOL_LENGTH_OFFSET_AXIS];
} else { // G49
gc_state.tool_length_offset = 0.0;
}
}
// [15. Coordinate system selection ]:
if (gc_state.modal.coord_select != gc_block.modal.coord_select) {
gc_state.modal.coord_select = gc_block.modal.coord_select;
memcpy(gc_state.coord_system,coordinate_data,sizeof(coordinate_data));
}
// [16. Set path control mode ]: NOT SUPPORTED
// [17. Set distance mode ]:
gc_state.modal.distance = gc_block.modal.distance;
// [18. Set retract mode ]: NOT SUPPORTED
// [19. Go to predefined position, Set G10, or Set axis offsets ]:
switch(gc_block.non_modal_command) {
case NON_MODAL_SET_COORDINATE_DATA:
settings_write_coord_data(coord_select,parameter_data);
// Update system coordinate system if currently active.
if (gc_state.modal.coord_select == coord_select) { memcpy(gc_state.coord_system,parameter_data,sizeof(parameter_data)); }
break;
case NON_MODAL_GO_HOME_0: case NON_MODAL_GO_HOME_1:
// Move to intermediate position before going home. Obeys current coordinate system and offsets
// and absolute and incremental modes.
if (axis_command) {
#ifdef USE_LINE_NUMBERS
mc_line(gc_block.values.xyz, -1.0, false, gc_block.values.n);
#else
mc_line(gc_block.values.xyz, -1.0, false);
#endif
}
#ifdef USE_LINE_NUMBERS
mc_line(parameter_data, -1.0, false, gc_block.values.n);
#else
mc_line(parameter_data, -1.0, false);
#endif
memcpy(gc_state.position, parameter_data, sizeof(parameter_data));
break;
case NON_MODAL_SET_HOME_0:
settings_write_coord_data(SETTING_INDEX_G28,gc_state.position);
break;
case NON_MODAL_SET_HOME_1:
settings_write_coord_data(SETTING_INDEX_G30,gc_state.position);
break;
case NON_MODAL_SET_COORDINATE_OFFSET:
memcpy(gc_state.coord_offset,gc_block.values.xyz,sizeof(gc_block.values.xyz));
break;
case NON_MODAL_RESET_COORDINATE_OFFSET:
clear_vector(gc_state.coord_offset); // Disable G92 offsets by zeroing offset vector.
break;
}
// [20. Motion modes ]:
// NOTE: Commands G10,G28,G30,G92 lock out and prevent axis words from use in motion modes.
// Enter motion modes only if there are axis words or a motion mode command word in the block.
gc_state.modal.motion = gc_block.modal.motion;
if (axis_command == AXIS_COMMAND_MOTION_MODE) {
switch (gc_state.modal.motion) {
case MOTION_MODE_SEEK:
#ifdef USE_LINE_NUMBERS
mc_line(gc_block.values.xyz, -1.0, false, gc_block.values.n);
#else
mc_line(gc_block.values.xyz, -1.0, false);
#endif
break;
case MOTION_MODE_LINEAR:
#ifdef USE_LINE_NUMBERS
mc_line(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate, gc_block.values.n);
#else
mc_line(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate);
#endif
break;
case MOTION_MODE_PROBE:
// NOTE: gc_block.values.xyz is returned from mc_probe_cycle with the updated position value. So
// upon a successful probing cycle, the machine position and the returned value should be the same.
#ifdef USE_LINE_NUMBERS
mc_probe_cycle(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate, gc_block.values.n);
#else
mc_probe_cycle(gc_block.values.xyz, gc_state.feed_rate, gc_state.modal.feed_rate);
#endif
}
// As far as the parser is concerned, the position is now == target. In reality the
// motion control system might still be processing the action and the real tool position
// in any intermediate location.
memcpy(gc_state.position, gc_block.values.xyz, sizeof(gc_block.values.xyz)); // gc.position[] = target[];
}
// [21. Program flow ]:
// M0,M2: Perform non-running program flow actions. During a program pause, the buffer may
// refill and can only be resumed by the cycle start run-time command.
gc_state.modal.program_flow = gc_block.modal.program_flow;
if (gc_state.modal.program_flow) {
protocol_buffer_synchronize(); // Finish all remaining buffered motions. Program paused when complete.
sys.auto_start = false; // Disable auto cycle start. Forces pause until cycle start issued.
// If complete, reset to reload defaults (G92.2,G54,G17,G90,G94,M48,G40,M5,M9). Otherwise,
// re-enable program flow after pause complete, where cycle start will resume the program.
if (gc_state.modal.program_flow == PROGRAM_FLOW_COMPLETED) { mc_reset(); }
else { gc_state.modal.program_flow = PROGRAM_FLOW_RUNNING; }
}
// [22. Laser control ]:
gc_state.modal.laser = gc_block.modal.laser;
laser_run(gc_block.values.t, gc_block.modal.laser);
// [23. Motor control ]:
gc_state.modal.motor = gc_block.modal.motor;
if (gc_block.modal.motor == MOTOR_ENABLE) {
st_disable_on_idle(false);
st_wake_up();
}
else {
st_disable_on_idle(true);
st_go_idle();
}
// [23. LDR read ]:
if (gc_block.modal.ldr == LDR_READ){
print_ldr(gc_block.values.t);
}
// TODO: % to denote start of program. Sets auto cycle start?
return(STATUS_OK);
}
