int qib_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int ret;
ret = pci_enable_device(pdev);
if (ret) {
/*
*/
qib_early_err(&pdev->dev, "pci enable failed: error %d\n",
-ret);
goto done;
}
ret = pci_request_regions(pdev, QIB_DRV_NAME);
if (ret) {
qib_devinfo(pdev, "pci_request_regions fails: err %d\n", -ret);
goto bail;
}
ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret) {
/*
*/
ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (ret) {
qib_devinfo(pdev, "Unable to set DMA mask: %d\n", ret);
goto bail;
}
ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
} else
ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret) {
qib_early_err(&pdev->dev,
"Unable to set DMA consistent mask: %d\n", ret);
goto bail;
}
pci_set_master(pdev);
ret = pci_enable_pcie_error_reporting(pdev);
if (ret) {
qib_early_err(&pdev->dev,
"Unable to enable pcie error reporting: %d\n",
ret);
ret = 0;
}
goto done;
bail:
pci_disable_device(pdev);
pci_release_regions(pdev);
done:
return ret;
}
/*
* Do all the common PCIe setup and initialization.
* devdata is not yet allocated, and is not allocated until after this
* routine returns success. Therefore qib_dev_err() can't be used for error
* printing.
*/
int qib_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int ret;
ret = pci_enable_device(pdev);
if (ret) {
/*
* This can happen (in theory) iff:
* We did a chip reset, and then failed to reprogram the
* BAR, or the chip reset due to an internal error. We then
* unloaded the driver and reloaded it.
*
* Both reset cases set the BAR back to initial state. For
* the latter case, the AER sticky error bit at offset 0x718
* should be set, but the Linux kernel doesn't yet know
* about that, it appears. If the original BAR was retained
* in the kernel data structures, this may be OK.
*/
qib_early_err(&pdev->dev, "pci enable failed: error %d\n",
-ret);
goto done;
}
ret = pci_request_regions(pdev, QIB_DRV_NAME);
if (ret) {
qib_devinfo(pdev, "pci_request_regions fails: err %d\n", -ret);
goto bail;
}
ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret) {
/*
* If the 64 bit setup fails, try 32 bit. Some systems
* do not setup 64 bit maps on systems with 2GB or less
* memory installed.
*/
ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (ret) {
qib_devinfo(pdev, "Unable to set DMA mask: %d\n", ret);
goto bail;
}
ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
} else
ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret) {
qib_early_err(&pdev->dev,
"Unable to set DMA consistent mask: %d\n", ret);
goto bail;
}
pci_set_master(pdev);
ret = pci_enable_pcie_error_reporting(pdev);
if (ret) {
qib_early_err(&pdev->dev,
"Unable to enable pcie error reporting: %d\n",
ret);
ret = 0;
}
goto done;
bail:
pci_disable_device(pdev);
pci_release_regions(pdev);
done:
return ret;
}
/*
* Do all the common PCIe setup and initialization.
* devdata is not yet allocated, and is not allocated until after this
* routine returns success. Therefore qib_dev_err() can't be used for error
* printing.
*/
int qib_pcie_init(struct pci_dev *pdev, const struct pci_device_id *ent)
{
int ret;
ret = pci_enable_device(pdev);
if (ret) {
/*
* This can happen (in theory) iff:
* We did a chip reset, and then failed to reprogram the
* BAR, or the chip reset due to an internal error. We then
* unloaded the driver and reloaded it.
*
* Both reset cases set the BAR back to initial state. For
* the latter case, the AER sticky error bit at offset 0x718
* should be set, but the Linux kernel doesn't yet know
* about that, it appears. If the original BAR was retained
* in the kernel data structures, this may be OK.
*/
qib_early_err(&pdev->dev, "pci enable failed: error %d\n",
-ret);
goto done;
}
ret = pci_request_regions(pdev, QIB_DRV_NAME);
if (ret) {
qib_devinfo(pdev, "pci_request_regions fails: err %d\n",
-ret);
goto bail;
}
ret = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
if (ret) {
/*
* If the 64 bit setup fails, try 32 bit. Some systems
* do not setup 64 bit maps on systems with 2GB or less
* memory installed.
*/
ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
if (ret) {
qib_devinfo(pdev, "Unable to set DMA mask: %d\n", ret);
goto bail;
}
qib_dbg("No 64bit DMA mask, used 32 bit mask\n");
ret = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
} else
ret = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
if (ret) {
qib_early_err(&pdev->dev,
"Unable to set DMA consistent mask: %d\n", ret);
goto bail;
}
pci_set_master(pdev);
#ifdef CONFIG_PCIEAER
/* enable basic AER reporting. Perhaps more later */
if (pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_ERR)) {
ret = pci_enable_pcie_error_reporting(pdev);
if (ret)
qib_early_err(&pdev->dev,
"Unable to enable pcie error reporting"
": %d\n", ret);
ret = 0;
} else
qib_dbg("AER capability not found! AER reports not enabled\n");
#endif
goto done;
bail:
pci_disable_device(pdev);
pci_release_regions(pdev);
done:
return ret;
}
