int main(void) {
SetupClock();
SwitchClocks();
SetupPorts();
//lcdSetup(4,20); // 4 rows & 20 cols
radioSetup(); // polling mode
bootSetup();
LED_1 = 1; LED_2 = 1; LED_3 = 1;
delay_ms(500);
LED_1 = 0; LED_2 = 0; LED_3 = 0;
delay_ms(200);
LED_1 = 1; LED_2 = 1; LED_3 = 1;
delay_ms(500);
// check if radio is working and at the right state.
while (radioGetTrxState() != 0x16);
LED_1 = 0;
LED_2 = 0;
LED_3 = 0;
//print("Ready");
//bootTestRadio();
bootRun();
bootReset();
while(1);
return 1;
}
void nodeSleep(u16 tenthSeconds)
{
// ************** Power down the other board peripherals
Leds_off();
// ************** Power down the radio
// wait for radio to be done
u8 state = BUSY_TX_ARET;
while (state == BUSY_TX_ARET ||
state == BUSY_RX_AACK)
state = radioGetTrxState();
// Now put radio to sleep
radioEnterSleepMode();
// TODO: figure out what needs to be put to sleep to minimize current consumption
// ************** Power down the on-chip modules
// PRR = 0xbf; ???
// Disable ADC
// ADCSRA &= ~(1 << ADEN);
// Turn off comparator
// ACSR |= (1 <<
// turn off ports etc
// Turn off BOD
// This should only be done once -- No need to do it over again
/*
AVR_ENTER_CRITICAL_REGION();
#define BODS 6
#define BODSE 5
MCUCR |= (1 << BODSE) | (1<< BODS);
MCUCR &= ~(1 << BODSE);
AVR_LEAVE_CRITICAL_REGION();
*/
// ************** Set the timer to wake up
// Set TIMER2 Asyncronous Mode.
ASSR |= (1 << AS2);
// Set TIMER2 Prescaler to 1024.
TCCR2B |= ((1 << CS22)|(1 << CS21)|(1 << CS20));
// Wait for TCNT2 write to finish.
while(ASSR & (1 << TCR2BUB))
;
// Sleep as many times as needed to sleep for the full time
while (tenthSeconds)
{
// This is to get the node manually out of sleeping mode --
// Might take up to 7.5Sec to detect button press
//
if (BUTTON_PRESSED() )
{
Led1_on();
macConfig.sleeping = false;
while (BUTTON_PRESSED())
;
Led1_off();
break; // exit the Sleeping loop
}
// Set TIMER2 output compare register from user.
if (tenthSeconds > 75)
{
// Just decrement by the max timeout
OCR2A = 240; // 7.5 seconds, max timeout
tenthSeconds -= 75;
}
else
{
// Can measure the remaining time in one timer cycle
tenthSeconds = tenthSeconds * 16 / 5;
if (!tenthSeconds)
tenthSeconds++;
OCR2A = tenthSeconds;
tenthSeconds = 0;
}
// Wait for OCR2 write to finish.
while(ASSR & (1 << OCR2AUB))
;
// Reset TIMER2 timer counter value.
TCNT2 = 0;
// Wait for TCNT2 write to finish before entering sleep.
while(ASSR & (1 << TCN2UB))
;
// Clear interrupt flag
TIFR2 |= (1 << OCF2A);
// Enable TIMER2 output compare interrupt.
TIMSK2 |= (1 << OCIE2A);
// ************** Go to sleep
AVR_ENTER_CRITICAL_REGION();
set_sleep_mode( SLEEP_MODE_PWR_SAVE);
sleep_enable();
sei();
sleep_cpu(); // sleeping right here
sleep_disable();
AVR_LEAVE_CRITICAL_REGION();
wdt_disable();
}
// ************** Awake now, wake up everything
// PRR = 0x03; ??
if (SERIAL)
serial_init(NULL);
debugMsgStr("\r\nNode slept");
if ( macConfig.associated)
HAL_ADC_INIT();
// Bring SPI port back up (must re-init after sleep)
radio_spi_init();
// Wake up radio.
radioLeaveSleepMode();
// Set RF212 to 250KB mode.
// TODO: do I need to call this??
//radioSetup900();
radioSetTrxState(PLL_ON);
}
