/**
* @brief Configures and activates the DAC peripheral.
*
* @param[in] dacp pointer to the @p DACDriver object
*
* @notapi
*/
void dac_lld_start(DACDriver *dacp) {
/* If the driver is in DAC_STOP state then a full initialization is
required.*/
if (dacp->state == DAC_STOP) {
/* Enabling the clock source.*/
#if STM32_DAC_USE_DAC1_CH1
if (&DACD1 == dacp) {
rccEnableDAC1(false);
}
#endif
#if STM32_DAC_USE_DAC1_CH2
if (&DACD2 == dacp) {
rccEnableDAC1(false);
}
#endif
#if STM32_DAC_USE_DAC2_CH1
if (&DACD3 == dacp) {
rccEnableDAC2(false);
}
#endif
#if STM32_DAC_USE_DAC2_CH2
if (&DACD3 == dacp) {
rccEnableDAC2(false);
}
#endif
/* Enabling DAC in SW triggering mode initially, initializing data to
zero.*/
#if STM32_DAC_DUAL_MODE == FALSE
dacp->params->dac->CR &= dacp->params->regmask;
dacp->params->dac->CR |= DAC_CR_EN1 << dacp->params->regshift;
dac_lld_put_channel(dacp, 0U, dacp->config->init);
#else
if ((dacp->config->datamode == DAC_DHRM_12BIT_RIGHT_DUAL) ||
(dacp->config->datamode == DAC_DHRM_12BIT_LEFT_DUAL) ||
(dacp->config->datamode == DAC_DHRM_8BIT_RIGHT_DUAL)) {
dacp->params->dac->CR = DAC_CR_EN2 | DAC_CR_EN1;
dac_lld_put_channel(dacp, 1U, dacp->config->init);
}
else {
dacp->params->dac->CR = DAC_CR_EN1;
}
dac_lld_put_channel(dacp, 0U, dacp->config->init);
#endif
}
}
/*
* Application entry point.
*/
int main(void) {
/*
* System initializations.
* - HAL initialization, this also initializes the configured device drivers
* and performs the board-specific initializations.
* - Kernel initialization, the main() function becomes a thread and the
* RTOS is active.
*/
halInit();
chSysInit();
/*
* Activates the serial driver 1 using the driver default configuration.
*/
sdStart(&SD1, NULL);
/*
* Starting GPT4 driver, it is used for triggering the ADC.
*/
gptStart(&GPTD4, &gpt4cfg1);
/*
* Fixed an errata on the STM32F7xx, the DAC clock is required for ADC
* triggering.
*/
rccEnableDAC1(false);
/*
* Activates the ADC1 driver and the temperature sensor.
*/
adcStart(&ADCD1, NULL);
adcSTM32EnableTSVREFE();
/*
* Starts an ADC continuous conversion triggered with a period of
* 1/10000 second.
*/
adcStartConversion(&ADCD1, &adcgrpcfg1, samples1, ADC_GRP1_BUF_DEPTH);
gptStartContinuous(&GPTD4, 100);
/*
* Creates the example thread.
*/
chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO, Thread1, NULL);
/*
* Normal main() thread activity, in this demo it does nothing.
*/
while (true) {
chThdSleepMilliseconds(500);
}
}
/**
* @brief Configures and activates the DAC peripheral.
*
* @param[in] dacp pointer to the @p DACDriver object
*
* @notapi
*/
void dac_lld_start(DACDriver *dacp) {
uint32_t arr, regshift, trgo, dataoffset;
bool b;
/* If in stopped state then enables the DAC and DMA clocks.*/
if (dacp->state == DAC_STOP) {
#if STM32_DAC_USE_CHN1
if (&DACD1 == dacp) {
rccEnableDAC1(FALSE);
/* DAC1 CR data is at bits 0:15 */
regshift = 0;
dataoffset = 0;
/* Timer setup */
rccEnableTIM6(FALSE);
rccResetTIM6();
trgo = STM32_DAC_CR_TSEL_TIM6;
}
#endif
#if STM32_DAC_USE_CHN2
if (&DACD2 == dacp) {
rccEnableDAC1(FALSE);
/* DAC2 CR data is at bits 16:31 */
regshift = 16;
dataoffset = &dacp->dac->DHR12R2 - &dacp->dac->DHR12R1;
/* Timer setup */
rccEnableTIM7(FALSE);
rccResetTIM7();
trgo = STM32_DAC_CR_TSEL_TIM7;
}
#endif
#if STM32_DAC_USE_CHN3
if (&DACD3 == dacp) {
rccEnableDAC2(FALSE);
/* DAC3 CR data is at bits 0:15 */
regshift = 0;
dataoffset = 0;
/* Timer setup */
rccEnableTIM18(FALSE);
rccResetTIM18();
trgo = STM32_DAC_CR_TSEL_TIM18;
}
#endif
#if STM32_DAC_USE_CHN1 || STM32_DAC_USE_CHN2 || STM32_DAC_USE_CHN3
dacp->clock = STM32_TIMCLK1;
arr = (dacp->clock / dacp->config->frequency);
osalDbgAssert((arr <= 0xFFFF),
"invalid frequency");
/* Timer configuration.*/
dacp->tim->CR1 = 0; /* Initially stopped. */
dacp->tim->PSC = 0; /* Prescaler value. */
dacp->tim->DIER = 0;
dacp->tim->ARR = arr;
dacp->tim->EGR = TIM_EGR_UG; /* Update event. */
dacp->tim->CR2 &= (uint16_t)~TIM_CR2_MMS;
dacp->tim->CR2 |= (uint16_t)TIM_CR2_MMS_1; /* Enable TRGO updates. */
dacp->tim->CNT = 0; /* Reset counter. */
dacp->tim->SR = 0; /* Clear pending IRQs. */
/* Update Event IRQ enabled. */
/* Timer start.*/
dacp->tim->CR1 = TIM_CR1_CEN;
/* DAC configuration */
dacp->dac->CR |= ( (dacp->dac->CR & ~STM32_DAC_CR_MASK) | \
(STM32_DAC_CR_EN | STM32_DAC_CR_DMAEN | dacp->config->cr_flags) ) << regshift;
/* DMA setup. */
b = dmaStreamAllocate(dacp->dma,
dacp->irqprio,
(stm32_dmaisr_t)dac_lld_serve_tx_interrupt,
(void *)dacp);
osalDbgAssert(!b, "stream already allocated");
switch (dacp->config->dhrm) {
/* Sets the DAC data register */
case DAC_DHRM_12BIT_RIGHT:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR12R1 + dataoffset);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
break;
case DAC_DHRM_12BIT_LEFT:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR12L1 + dataoffset);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
break;
case DAC_DHRM_8BIT_RIGHT:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR8R1 + dataoffset);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_BYTE | STM32_DMA_CR_MSIZE_BYTE;
break;
#if defined(STM32_HAS_DAC_CHN2) && STM32_HAS_DAC_CHN2
case DAC_DHRM_12BIT_RIGHT_DUAL:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR12RD);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
break;
case DAC_DHRM_12BIT_LEFT_DUAL:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR12LD);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_HWORD | STM32_DMA_CR_MSIZE_HWORD;
break;
case DAC_DHRM_8BIT_RIGHT_DUAL:
dmaStreamSetPeripheral(dacp->dma, &dacp->dac->DHR8RD);
dacp->dmamode = (dacp->dmamode & ~STM32_DMA_CR_SIZE_MASK) |
STM32_DMA_CR_PSIZE_BYTE | STM32_DMA_CR_MSIZE_BYTE;
break;
#endif
}
dacp->dac->CR |= trgo << regshift; /* Enable timer trigger */
#endif
}
}
