/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAHB3(~0);
rccResetAPB1R1(~RCC_APB1RSTR1_PWRRST);
rccResetAPB1R2(~0);
rccResetAPB2(~0);
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR1 |= PWR_CR1_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(!0);
rccResetAHB2(!0);
rccResetAHB3(!0);
rccResetAPB1(!RCC_APB1RSTR_PWRRST);
rccResetAPB2(!0);
/* SysTick initialization using the system clock.*/
SysTick->LOAD = STM32_HCLK / CH_FREQUENCY - 1;
SysTick->VAL = 0;
SysTick->CTRL = SysTick_CTRL_CLKSOURCE_Msk |
SysTick_CTRL_ENABLE_Msk |
SysTick_CTRL_TICKINT_Msk;
/* DWT cycle counter enable.*/
DWT_CTRL |= DWT_CTRL_CYCCNTENA;
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
/**
* @brief Low level HAL driver initialization.
*
* @notapi
*/
void hal_lld_init(void) {
/* Reset of all peripherals. AHB3 is not reseted because it could have
been initialized in the board initialization file (board.c).*/
rccResetAHB1(~0);
rccResetAHB2(~0);
rccResetAHB3(~0);
rccResetAPB1(~RCC_APB1RSTR_PWRRST);
rccResetAPB2(~0);
/* SysTick initialization using the system clock.*/
Clk.InitSysTick();
/* DWT cycle counter enable.*/
SCS_DEMCR |= SCS_DEMCR_TRCENA;
DWT_CTRL |= DWT_CTRL_CYCCNTENA;
/* PWR clock enabled.*/
rccEnablePWRInterface(FALSE);
/* Initializes the backup domain.*/
hal_lld_backup_domain_init();
#if defined(STM32_DMA_REQUIRED)
dmaInit();
#endif
/* Programmable voltage detector enable.*/
#if STM32_PVD_ENABLE
PWR->CR |= PWR_CR_PVDE | (STM32_PLS & STM32_PLS_MASK);
#endif /* STM32_PVD_ENABLE */
}
