void rtl8180_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
{
struct rtl8180_priv *priv = dev->priv;
int i = 10;
u32 buf;
buf = (data << 8) | addr;
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf | 0x80);
while (i--) {
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->PHY[0], buf);
if (rtl818x_ioread8(priv, &priv->map->PHY[2]) == (data & 0xFF))
return;
}
}
static void rtl8180_configure_filter(struct ieee80211_hw *dev,
unsigned int changed_flags,
unsigned int *total_flags,
int mc_count, struct dev_addr_list *mclist)
{
struct rtl8180_priv *priv = dev->priv;
if (changed_flags & FIF_FCSFAIL)
priv->rx_conf ^= RTL818X_RX_CONF_FCS;
if (changed_flags & FIF_CONTROL)
priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
if (changed_flags & FIF_OTHER_BSS)
priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
if (*total_flags & FIF_ALLMULTI || mc_count > 0)
priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
else
priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
*total_flags = 0;
if (priv->rx_conf & RTL818X_RX_CONF_FCS)
*total_flags |= FIF_FCSFAIL;
if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
*total_flags |= FIF_CONTROL;
if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
*total_flags |= FIF_OTHER_BSS;
if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
*total_flags |= FIF_ALLMULTI;
rtl818x_iowrite32(priv, &priv->map->RX_CONF, priv->rx_conf);
}
static int rtl8180_add_interface(struct ieee80211_hw *dev,
struct ieee80211_if_init_conf *conf)
{
struct rtl8180_priv *priv = dev->priv;
if (priv->mode != NL80211_IFTYPE_MONITOR)
return -EOPNOTSUPP;
switch (conf->type) {
case NL80211_IFTYPE_STATION:
priv->mode = conf->type;
break;
default:
return -EOPNOTSUPP;
}
priv->vif = conf->vif;
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
rtl818x_iowrite32(priv, (__le32 __iomem *)&priv->map->MAC[0],
le32_to_cpu(*(__le32 *)conf->mac_addr));
rtl818x_iowrite16(priv, (__le16 __iomem *)&priv->map->MAC[4],
le16_to_cpu(*(__le16 *)(conf->mac_addr + 4)));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
return 0;
}
/* Sets the MAC address of the card. */
static void rtl818x_set_hwaddr(struct net80211_device *dev, u8 *hwaddr)
{
struct rtl818x_priv *priv = dev->priv;
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
rtl818x_iowrite32(priv, (u32 *)&priv->map->MAC[0],
le32_to_cpu(*(u32 *)hwaddr));
rtl818x_iowrite16(priv, (u16 *)&priv->map->MAC[4],
le16_to_cpu(*(u16 *)(hwaddr + 4)));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
}
void rtl8180_set_anaparam(struct rtl8180_priv *priv, u32 anaparam)
{
u8 reg;
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
rtl818x_iowrite8(priv, &priv->map->CONFIG3,
reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam);
rtl818x_iowrite8(priv, &priv->map->CONFIG3,
reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
}
static void write_max2820(struct ieee80211_hw *dev, u8 addr, u32 data)
{
struct rtl8180_priv *priv = dev->priv;
u32 phy_config;
phy_config = 0x90 + (data & 0xf);
phy_config <<= 16;
phy_config += addr;
phy_config <<= 8;
phy_config += (data >> 4) & 0xff;
rtl818x_iowrite32(priv,
(__le32 __iomem *) &priv->map->RFPinsOutput, phy_config);
msleep(1);
}
static void write_sa2400(struct ieee80211_hw *dev, u8 addr, u32 data)
{
struct rtl8180_priv *priv = dev->priv;
u32 phy_config;
/* MAC will bang bits to the sa2400. sw 3-wire is NOT used */
phy_config = 0xb0000000;
phy_config |= ((u32)(addr & 0xf)) << 24;
phy_config |= data & 0xffffff;
rtl818x_iowrite32(priv,
(__le32 __iomem *) &priv->map->RFPinsOutput, phy_config);
msleep(3);
}
static void write_grf5101(struct ieee80211_hw *dev, u8 addr, u32 data)
{
struct rtl8180_priv *priv = dev->priv;
u32 phy_config;
phy_config = grf5101_encode[(data >> 8) & 0xF];
phy_config |= grf5101_encode[(data >> 4) & 0xF] << 4;
phy_config |= grf5101_encode[data & 0xF] << 8;
phy_config |= grf5101_encode[(addr >> 1) & 0xF] << 12;
phy_config |= (addr & 1) << 16;
phy_config |= grf5101_encode[(data & 0xf000) >> 12] << 24;
/* MAC will bang bits to the chip */
phy_config |= 0x90000000;
rtl818x_iowrite32(priv,
(__le32 __iomem *) &priv->map->RFPinsOutput, phy_config);
msleep(3);
}
static int rtl8180_start(struct ieee80211_hw *dev)
{
struct rtl8180_priv *priv = dev->priv;
int ret, i;
u32 reg;
ret = rtl8180_init_rx_ring(dev);
if (ret)
return ret;
for (i = 0; i < 4; i++)
if ((ret = rtl8180_init_tx_ring(dev, i, 16)))
goto err_free_rings;
ret = rtl8180_init_hw(dev);
if (ret)
goto err_free_rings;
rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma);
rtl818x_iowrite32(priv, &priv->map->TBDA, priv->tx_ring[3].dma);
rtl818x_iowrite32(priv, &priv->map->THPDA, priv->tx_ring[2].dma);
rtl818x_iowrite32(priv, &priv->map->TNPDA, priv->tx_ring[1].dma);
rtl818x_iowrite32(priv, &priv->map->TLPDA, priv->tx_ring[0].dma);
ret = request_irq(priv->pdev->irq, &rtl8180_interrupt,
IRQF_SHARED, KBUILD_MODNAME, dev);
if (ret) {
printk(KERN_ERR "%s: failed to register IRQ handler\n",
wiphy_name(dev->wiphy));
goto err_free_rings;
}
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
reg = RTL818X_RX_CONF_ONLYERLPKT |
RTL818X_RX_CONF_RX_AUTORESETPHY |
RTL818X_RX_CONF_MGMT |
RTL818X_RX_CONF_DATA |
(7 << 8 /* MAX RX DMA */) |
RTL818X_RX_CONF_BROADCAST |
RTL818X_RX_CONF_NICMAC;
if (priv->r8185)
reg |= RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2;
else {
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE1)
? RTL818X_RX_CONF_CSDM1 : 0;
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE2)
? RTL818X_RX_CONF_CSDM2 : 0;
}
priv->rx_conf = reg;
rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
if (priv->r8185) {
reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT;
reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT;
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
reg |= RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
/* disable early TX */
rtl818x_iowrite8(priv, (u8 __iomem *)priv->map + 0xec, 0x3f);
}
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
reg |= (6 << 21 /* MAX TX DMA */) |
RTL818X_TX_CONF_NO_ICV;
if (priv->r8185)
reg &= ~RTL818X_TX_CONF_PROBE_DTS;
else
reg &= ~RTL818X_TX_CONF_HW_SEQNUM;
/* different meaning, same value on both rtl8185 and rtl8180 */
reg &= ~RTL818X_TX_CONF_SAT_HWPLCP;
rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
reg = rtl818x_ioread8(priv, &priv->map->CMD);
reg |= RTL818X_CMD_RX_ENABLE;
reg |= RTL818X_CMD_TX_ENABLE;
rtl818x_iowrite8(priv, &priv->map->CMD, reg);
priv->mode = NL80211_IFTYPE_MONITOR;
return 0;
err_free_rings:
rtl8180_free_rx_ring(dev);
for (i = 0; i < 4; i++)
if (priv->tx_ring[i].desc)
rtl8180_free_tx_ring(dev, i);
return ret;
}
static int rtl8180_init_hw(struct ieee80211_hw *dev)
{
struct rtl8180_priv *priv = dev->priv;
u16 reg;
rtl818x_iowrite8(priv, &priv->map->CMD, 0);
rtl818x_ioread8(priv, &priv->map->CMD);
msleep(10);
/* reset */
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
rtl818x_ioread8(priv, &priv->map->CMD);
reg = rtl818x_ioread8(priv, &priv->map->CMD);
reg &= (1 << 1);
reg |= RTL818X_CMD_RESET;
rtl818x_iowrite8(priv, &priv->map->CMD, RTL818X_CMD_RESET);
rtl818x_ioread8(priv, &priv->map->CMD);
msleep(200);
/* check success of reset */
if (rtl818x_ioread8(priv, &priv->map->CMD) & RTL818X_CMD_RESET) {
printk(KERN_ERR "%s: reset timeout!\n", wiphy_name(dev->wiphy));
return -ETIMEDOUT;
}
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
rtl818x_ioread8(priv, &priv->map->CMD);
msleep(200);
if (rtl818x_ioread8(priv, &priv->map->CONFIG3) & (1 << 3)) {
/* For cardbus */
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
reg |= 1 << 1;
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
reg = rtl818x_ioread16(priv, &priv->map->FEMR);
reg |= (1 << 15) | (1 << 14) | (1 << 4);
rtl818x_iowrite16(priv, &priv->map->FEMR, reg);
}
rtl818x_iowrite8(priv, &priv->map->MSR, 0);
if (!priv->r8185)
rtl8180_set_anaparam(priv, priv->anaparam);
rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma);
rtl818x_iowrite32(priv, &priv->map->TBDA, priv->tx_ring[3].dma);
rtl818x_iowrite32(priv, &priv->map->THPDA, priv->tx_ring[2].dma);
rtl818x_iowrite32(priv, &priv->map->TNPDA, priv->tx_ring[1].dma);
rtl818x_iowrite32(priv, &priv->map->TLPDA, priv->tx_ring[0].dma);
/* TODO: necessary? specs indicate not */
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
reg = rtl818x_ioread8(priv, &priv->map->CONFIG2);
rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg & ~(1 << 3));
if (priv->r8185) {
reg = rtl818x_ioread8(priv, &priv->map->CONFIG2);
rtl818x_iowrite8(priv, &priv->map->CONFIG2, reg | (1 << 4));
}
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
/* TODO: set CONFIG5 for calibrating AGC on rtl8180 + philips radio? */
/* TODO: turn off hw wep on rtl8180 */
rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
if (priv->r8185) {
rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81);
rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
/* TODO: set ClkRun enable? necessary? */
reg = rtl818x_ioread8(priv, &priv->map->GP_ENABLE);
rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, reg & ~(1 << 6));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | (1 << 2));
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
} else {
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x1);
rtl818x_iowrite8(priv, &priv->map->SECURITY, 0);
rtl818x_iowrite8(priv, &priv->map->PHY_DELAY, 0x6);
rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, 0x4C);
}
priv->rf->init(dev);
if (priv->r8185)
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
return 0;
}
static void sa2400_rf_init(struct ieee80211_hw *dev)
{
struct rtl8180_priv *priv = dev->priv;
u32 anaparam, txconf;
u8 firdac;
int analogphy = priv->rfparam & RF_PARAM_ANALOGPHY;
anaparam = priv->anaparam;
anaparam &= ~(1 << ANAPARAM_TXDACOFF_SHIFT);
anaparam &= ~ANAPARAM_PWR1_MASK;
anaparam &= ~ANAPARAM_PWR0_MASK;
if (analogphy) {
anaparam |= SA2400_ANA_ANAPARAM_PWR1_ON << ANAPARAM_PWR1_SHIFT;
firdac = 0;
} else {
anaparam |= (SA2400_DIG_ANAPARAM_PWR1_ON << ANAPARAM_PWR1_SHIFT);
anaparam |= (SA2400_ANAPARAM_PWR0_ON << ANAPARAM_PWR0_SHIFT);
firdac = 1 << SA2400_REG4_FIRDAC_SHIFT;
}
rtl8180_set_anaparam(priv, anaparam);
write_sa2400(dev, 0, sa2400_chan[0]);
write_sa2400(dev, 1, 0xbb50);
write_sa2400(dev, 2, 0x80);
write_sa2400(dev, 3, 0);
write_sa2400(dev, 4, 0x19340 | firdac);
write_sa2400(dev, 5, 0x1dfb | (SA2400_MAX_SENS - 54) << 15);
write_sa2400(dev, 4, 0x19348 | firdac); /* calibrate VCO */
if (!analogphy)
write_sa2400(dev, 4, 0x1938c); /*???*/
write_sa2400(dev, 4, 0x19340 | firdac);
write_sa2400(dev, 0, sa2400_chan[0]);
write_sa2400(dev, 1, 0xbb50);
write_sa2400(dev, 2, 0x80);
write_sa2400(dev, 3, 0);
write_sa2400(dev, 4, 0x19344 | firdac); /* calibrate filter */
/* new from rtl8180 embedded driver (rtl8181 project) */
write_sa2400(dev, 6, 0x13ff | (1 << 23)); /* MANRX */
write_sa2400(dev, 8, 0); /* VCO */
if (analogphy) {
rtl8180_set_anaparam(priv, anaparam |
(1 << ANAPARAM_TXDACOFF_SHIFT));
txconf = rtl818x_ioread32(priv, &priv->map->TX_CONF);
rtl818x_iowrite32(priv, &priv->map->TX_CONF,
txconf | RTL818X_TX_CONF_LOOPBACK_CONT);
write_sa2400(dev, 4, 0x19341); /* calibrates DC */
/* a 5us sleep is required here,
* we rely on the 3ms delay introduced in write_sa2400 */
write_sa2400(dev, 4, 0x19345);
/* a 20us sleep is required here,
* we rely on the 3ms delay introduced in write_sa2400 */
rtl818x_iowrite32(priv, &priv->map->TX_CONF, txconf);
rtl8180_set_anaparam(priv, anaparam);
}
/* end new code */
write_sa2400(dev, 4, 0x19341 | firdac); /* RTX MODE */
/* baseband configuration */
rtl8180_write_phy(dev, 0, 0x98);
rtl8180_write_phy(dev, 3, 0x38);
rtl8180_write_phy(dev, 4, 0xe0);
rtl8180_write_phy(dev, 5, 0x90);
rtl8180_write_phy(dev, 6, 0x1a);
rtl8180_write_phy(dev, 7, 0x64);
sa2400_write_phy_antenna(dev, 1);
rtl8180_write_phy(dev, 0x11, 0x80);
if (rtl818x_ioread8(priv, &priv->map->CONFIG2) &
RTL818X_CONFIG2_ANTENNA_DIV)
rtl8180_write_phy(dev, 0x12, 0xc7); /* enable ant diversity */
else
rtl8180_write_phy(dev, 0x12, 0x47); /* disable ant diversity */
rtl8180_write_phy(dev, 0x13, 0x90 | priv->csthreshold);
rtl8180_write_phy(dev, 0x19, 0x0);
rtl8180_write_phy(dev, 0x1a, 0xa0);
}
static int rtl818x_start(struct net80211_device *dev)
{
struct rtl818x_priv *priv = dev->priv;
int ret;
u32 reg;
ret = rtl818x_init_rx_ring(dev);
if (ret)
return ret;
ret = rtl818x_init_tx_ring(dev);
if (ret)
goto err_free_rings;
ret = rtl818x_init_hw(dev);
if (ret)
goto err_free_rings;
rtl818x_set_hwaddr(dev, dev->netdev->ll_addr);
rtl818x_iowrite32(priv, &priv->map->RDSAR, priv->rx_ring_dma);
rtl818x_iowrite32(priv, &priv->map->TNPDA, priv->tx_ring_dma);
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
reg = RTL818X_RX_CONF_ONLYERLPKT |
RTL818X_RX_CONF_RX_AUTORESETPHY |
RTL818X_RX_CONF_MGMT |
RTL818X_RX_CONF_DATA |
(7 << 8 /* MAX RX DMA */) |
RTL818X_RX_CONF_BROADCAST |
RTL818X_RX_CONF_NICMAC;
if (priv->r8185)
reg |= RTL818X_RX_CONF_CSDM1 | RTL818X_RX_CONF_CSDM2;
else {
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE1)
? RTL818X_RX_CONF_CSDM1 : 0;
reg |= (priv->rfparam & RF_PARAM_CARRIERSENSE2)
? RTL818X_RX_CONF_CSDM2 : 0;
}
priv->rx_conf = reg;
rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
if (priv->r8185) {
reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT;
reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT;
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
reg |= RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
/* disable early TX */
rtl818x_iowrite8(priv, (u8 *)priv->map + 0xec, 0x3f);
}
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
reg |= (6 << 21 /* MAX TX DMA */) |
RTL818X_TX_CONF_NO_ICV;
if (priv->r8185)
reg &= ~RTL818X_TX_CONF_PROBE_DTS;
else
reg &= ~RTL818X_TX_CONF_HW_SEQNUM;
/* different meaning, same value on both rtl8185 and rtl8180 */
reg &= ~RTL818X_TX_CONF_SAT_HWPLCP;
rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
reg = rtl818x_ioread8(priv, &priv->map->CMD);
reg |= RTL818X_CMD_RX_ENABLE;
reg |= RTL818X_CMD_TX_ENABLE;
rtl818x_iowrite8(priv, &priv->map->CMD, reg);
DBG("%s rtl818x: started\n", dev->netdev->name);
return 0;
err_free_rings:
rtl818x_free_rx_ring(dev);
if (priv->tx_ring)
rtl818x_free_tx_ring(dev);
DBG("%s rtl818x: failed to start\n", dev->netdev->name);
return ret;
}
