/* Initialize hardware */
int s5p_mfc_init_hw(struct s5p_mfc_dev *dev)
{
char fimv_info;
int fw_ver;
int ret = 0;
mfc_debug_enter();
if (!dev) {
mfc_err("no mfc device to run\n");
return -EINVAL;
}
/* RMVME: */
if (!s5p_mfc_bitproc_buf)
return -EINVAL;
/* 0. MFC reset */
mfc_debug(2, "MFC reset...\n");
s5p_mfc_clock_on();
ret = s5p_mfc_reset(dev);
if (ret) {
mfc_err("Failed to reset MFC - timeout.\n");
goto err_init_hw;
}
mfc_debug(2, "Done MFC reset...\n");
/* 1. Set DRAM base Addr */
s5p_mfc_init_memctrl(dev);
/* 2. Initialize registers of channel I/F */
s5p_mfc_clear_cmds(dev);
s5p_mfc_clean_dev_int_flags(dev);
/* 3. Release reset signal to the RISC */
if (IS_MFCV6(dev))
s5p_mfc_write_reg(0x1, S5P_FIMV_RISC_ON);
else
s5p_mfc_write_reg(0x3ff, S5P_FIMV_SW_RESET);
mfc_debug(2, "Will now wait for completion of firmware transfer.\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_FW_STATUS_RET)) {
mfc_err("Failed to load firmware.\n");
s5p_mfc_clean_dev_int_flags(dev);
ret = -EIO;
goto err_init_hw;
}
s5p_mfc_clean_dev_int_flags(dev);
/* 4. Initialize firmware */
ret = s5p_mfc_sys_init_cmd(dev);
if (ret) {
mfc_err("Failed to send command to MFC - timeout.\n");
goto err_init_hw;
}
mfc_debug(2, "Ok, now will write a command to init the system\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_SYS_INIT_RET)) {
mfc_err("Failed to load firmware\n");
ret = -EIO;
goto err_init_hw;
}
dev->int_cond = 0;
if (dev->int_err != 0 || dev->int_type !=
S5P_FIMV_R2H_CMD_SYS_INIT_RET) {
/* Failure. */
mfc_err("Failed to init firmware - error: %d"
" int: %d.\n", dev->int_err, dev->int_type);
ret = -EIO;
goto err_init_hw;
}
fimv_info = MFC_GET_REG(SYS_FW_FIMV_INFO);
if (fimv_info != 'D' && fimv_info != 'E')
fimv_info = 'N';
mfc_info("MFC v%x.%x, F/W: %02xyy, %02xmm, %02xdd (%c)\n",
MFC_VER_MAJOR(dev),
MFC_VER_MINOR(dev),
MFC_GET_REG(SYS_FW_VER_YEAR),
MFC_GET_REG(SYS_FW_VER_MONTH),
MFC_GET_REG(SYS_FW_VER_DATE),
fimv_info);
dev->fw.date = MFC_GET_REG(SYS_FW_VER_ALL);
/* Check MFC version and F/W version */
if (IS_MFCV6(dev) && FW_HAS_VER_INFO(dev)) {
fw_ver = MFC_GET_REG(SYS_MFC_VER);
if (fw_ver != mfc_version(dev)) {
mfc_err("Invalid F/W version(0x%x) for MFC H/W(0x%x)\n",
fw_ver, mfc_version(dev));
ret = -EIO;
goto err_init_hw;
}
}
err_init_hw:
s5p_mfc_clock_off();
mfc_debug_leave();
return ret;
}
/* Initialize hardware */
int s5p_mfc_init_hw(struct s5p_mfc_dev *dev)
{
int ret;
mfc_debug_enter();
/* RMVME: */
if (!s5p_mfc_bitproc_buf)
return -EINVAL;
/* 0. MFC reset */
mfc_debug(2, "MFC reset...\n");
s5p_mfc_clock_on();
ret = s5p_mfc_reset(dev);
if (ret) {
mfc_err("Failed to reset MFC - timeout.\n");
return ret;
}
mfc_debug(2, "Done MFC reset...\n");
/* 1. Set DRAM base Addr */
s5p_mfc_init_memctrl(dev);
/* 2. Initialize registers of channel I/F */
s5p_mfc_clear_cmds(dev);
/* 3. Release reset signal to the RISC */
if (IS_MFCV6(dev))
s5p_mfc_write_reg(0x1, S5P_FIMV_RISC_ON);
else
s5p_mfc_write_reg(0x3ff, S5P_FIMV_SW_RESET);
mfc_debug(2, "Will now wait for completion of firmware transfer.\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_FW_STATUS_RET)) {
mfc_err("Failed to load firmware.\n");
s5p_mfc_clean_dev_int_flags(dev);
return -EIO;
}
s5p_mfc_clean_dev_int_flags(dev);
/* 4. Initialize firmware */
ret = s5p_mfc_sys_init_cmd(dev);
if (ret) {
mfc_err("Failed to send command to MFC - timeout.\n");
return ret;
}
mfc_debug(2, "Ok, now will write a command to init the system\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_SYS_INIT_RET)) {
mfc_err("Failed to load firmware\n");
return -EIO;
}
dev->int_cond = 0;
if (dev->int_err != 0 || dev->int_type !=
S5P_FIMV_R2H_CMD_SYS_INIT_RET) {
/* Failure. */
mfc_err("Failed to init firmware - error: %d"
" int: %d.\n",dev->int_err, dev->int_type);
return -EIO;
}
mfc_info("MFC F/W version : %02xyy, %02xmm, %02xdd\n",
MFC_GET_REG(SYS_FW_VER_YEAR),
MFC_GET_REG(SYS_FW_VER_MONTH),
MFC_GET_REG(SYS_FW_VER_DATE));
s5p_mfc_clock_off();
mfc_debug_leave();
return 0;
}
/* Initialize hardware */
int mfc_init_hw(struct s5p_mfc_dev *dev, enum mfc_buf_usage_type buf_type)
{
char fimv_info;
int fw_ver;
int ret = 0;
int curr_ctx_backup;
mfc_debug_enter();
if (!dev) {
mfc_err("no mfc device to run\n");
return -EINVAL;
}
curr_ctx_backup = dev->curr_ctx_drm;
dev->sys_init_status = 0;
/* RMVME: */
if (!dev->fw_info.alloc)
return -EINVAL;
/* 0. MFC reset */
mfc_debug(2, "MFC reset...\n");
/* At init time, do not call secure API */
if (buf_type == MFCBUF_NORMAL)
dev->curr_ctx_drm = 0;
else if (buf_type == MFCBUF_DRM)
dev->curr_ctx_drm = 1;
ret = s5p_mfc_clock_on(dev);
if (ret) {
mfc_err_dev("Failed to enable clock before reset(%d)\n", ret);
dev->curr_ctx_drm = curr_ctx_backup;
return ret;
}
dev->sys_init_status = 1;
ret = s5p_mfc_reset(dev);
if (ret) {
mfc_err_dev("Failed to reset MFC - timeout.\n");
goto err_init_hw;
}
mfc_debug(2, "Done MFC reset...\n");
/* 1. Set DRAM base Addr */
s5p_mfc_init_memctrl(dev, buf_type);
/* 2. Initialize registers of channel I/F */
s5p_mfc_clear_cmds(dev);
s5p_mfc_clean_dev_int_flags(dev);
/* 3. Release reset signal to the RISC */
if (IS_MFCV6(dev))
s5p_mfc_write_reg(dev, 0x1, S5P_FIMV_RISC_ON);
else
s5p_mfc_write_reg(dev, 0x3ff, S5P_FIMV_SW_RESET);
mfc_debug(2, "Will now wait for completion of firmware transfer.\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_FW_STATUS_RET)) {
mfc_err_dev("Failed to load firmware.\n");
s5p_mfc_clean_dev_int_flags(dev);
ret = -EIO;
goto err_init_hw;
}
s5p_mfc_clean_dev_int_flags(dev);
/* 4. Initialize firmware */
ret = s5p_mfc_sys_init_cmd(dev, buf_type);
if (ret) {
mfc_err_dev("Failed to send command to MFC - timeout.\n");
goto err_init_hw;
}
mfc_debug(2, "Ok, now will write a command to init the system\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_SYS_INIT_RET)) {
mfc_err_dev("Failed to load firmware\n");
ret = -EIO;
goto err_init_hw;
}
dev->int_cond = 0;
if (dev->int_err != 0 || dev->int_type !=
S5P_FIMV_R2H_CMD_SYS_INIT_RET) {
/* Failure. */
mfc_err_dev("Failed to init firmware - error: %d"
" int: %d.\n", dev->int_err, dev->int_type);
ret = -EIO;
goto err_init_hw;
}
fimv_info = MFC_GET_REG(SYS_FW_FIMV_INFO);
if (fimv_info != 'D' && fimv_info != 'E')
fimv_info = 'N';
mfc_info_dev("MFC v%x.%x, F/W: %02xyy, %02xmm, %02xdd (%c)\n",
MFC_VER_MAJOR(dev),
MFC_VER_MINOR(dev),
MFC_GET_REG(SYS_FW_VER_YEAR),
MFC_GET_REG(SYS_FW_VER_MONTH),
MFC_GET_REG(SYS_FW_VER_DATE),
fimv_info);
dev->fw.date = MFC_GET_REG(SYS_FW_VER_ALL);
/* Check MFC version and F/W version */
if (IS_MFCV6(dev) && FW_HAS_VER_INFO(dev)) {
fw_ver = MFC_GET_REG(SYS_MFC_VER);
if (fw_ver != mfc_version(dev)) {
mfc_err_dev("Invalid F/W version(0x%x) for MFC H/W(0x%x)\n",
fw_ver, mfc_version(dev));
ret = -EIO;
goto err_init_hw;
}
}
#ifdef CONFIG_EXYNOS_CONTENT_PATH_PROTECTION
/* Cache flush for base address change */
if (FW_HAS_BASE_CHANGE(dev)) {
s5p_mfc_clean_dev_int_flags(dev);
s5p_mfc_cmd_host2risc(dev, S5P_FIMV_CH_CACHE_FLUSH, NULL);
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_CACHE_FLUSH_RET)) {
mfc_err_dev("Failed to flush cache\n");
ret = -EIO;
goto err_init_hw;
}
if (buf_type == MFCBUF_DRM && !curr_ctx_backup) {
s5p_mfc_clock_off(dev);
dev->curr_ctx_drm = curr_ctx_backup;
s5p_mfc_clock_on_with_base(dev, MFCBUF_NORMAL);
} else if (buf_type == MFCBUF_NORMAL && curr_ctx_backup) {
s5p_mfc_init_memctrl(dev, MFCBUF_DRM);
}
}
#endif
err_init_hw:
s5p_mfc_clock_off(dev);
dev->curr_ctx_drm = curr_ctx_backup;
mfc_debug_leave();
return ret;
}
int s5p_mfc_init_hw(struct s5p_mfc_dev *dev)
{
unsigned int ver;
int ret;
mfc_debug_enter();
if (!s5p_mfc_bitproc_buf)
return -EINVAL;
mfc_debug(2, "MFC reset..\n");
s5p_mfc_clock_on();
ret = s5p_mfc_reset(dev);
if (ret) {
mfc_err("Failed to reset MFC - timeout\n");
return ret;
}
mfc_debug(2, "Done MFC reset..\n");
s5p_mfc_init_memctrl(dev);
s5p_mfc_clear_cmds(dev);
s5p_mfc_clean_dev_int_flags(dev);
mfc_write(dev, 0x3ff, S5P_FIMV_SW_RESET);
mfc_debug(2, "Will now wait for completion of firmware transfer\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_FW_STATUS_RET)) {
mfc_err("Failed to load firmware\n");
s5p_mfc_reset(dev);
s5p_mfc_clock_off();
return -EIO;
}
s5p_mfc_clean_dev_int_flags(dev);
ret = s5p_mfc_sys_init_cmd(dev);
if (ret) {
mfc_err("Failed to send command to MFC - timeout\n");
s5p_mfc_reset(dev);
s5p_mfc_clock_off();
return ret;
}
mfc_debug(2, "Ok, now will write a command to init the system\n");
if (s5p_mfc_wait_for_done_dev(dev, S5P_FIMV_R2H_CMD_SYS_INIT_RET)) {
mfc_err("Failed to load firmware\n");
s5p_mfc_reset(dev);
s5p_mfc_clock_off();
return -EIO;
}
dev->int_cond = 0;
if (dev->int_err != 0 || dev->int_type !=
S5P_FIMV_R2H_CMD_SYS_INIT_RET) {
mfc_err("Failed to init firmware - error: %d int: %d\n",
dev->int_err, dev->int_type);
s5p_mfc_reset(dev);
s5p_mfc_clock_off();
return -EIO;
}
ver = mfc_read(dev, S5P_FIMV_FW_VERSION);
mfc_debug(2, "MFC F/W version : %02xyy, %02xmm, %02xdd\n",
(ver >> 16) & 0xFF, (ver >> 8) & 0xFF, ver & 0xFF);
s5p_mfc_clock_off();
mfc_debug_leave();
return 0;
}