/**************************************************************************************************
* @fn main
*
* @brief ISR for the reset vector.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void main(void)
{
uint8 time_spent_validating;
uint8 bootloaderForcedByMainApp = FALSE;
uint32 mainAppCommandLocal = mainAppCommand;
mainAppCommand = MAIN_APP_CMD_NONE;
if (mainAppCommandLocal == MAIN_APP_CMD_FORCE_BOOTLOADER)
{
bootloaderForcedByMainApp = TRUE;
}
else if ((mainAppCommandLocal == MAIN_APP_CMD_PASS_THROUGH) || ((SLEEPSTA & LRESET) == RESETWD))
/* If reset due to WatchDog Timer - Transfer control to the main application immediately.
WatchDog Timer reset causes the hardware to disconnect the USB. Without this jump here,
the SBL code will try to initiaize the CDC too early, which causes undesired behavior
on the host (e.g. on beaglebone black - the host gets stuck) */
{
asm("LJMP 0x2000\n");
}
sblInit();
if ((!bootloaderForcedByMainApp) && sbImgValid(&time_spent_validating))
{
if (sblWait(SBL_WAIT_TIME > time_spent_validating ? SBL_WAIT_TIME - time_spent_validating : 0))
{
if (znpCfg1 == ZNP_CFG1_SPI)
{
HalUARTUnInitSPI();
}
else
{
sbReportState(SB_STATE_EXECUTING_IMAGE);
while(sblIsUartTxPending())
{
sbUartPoll();
}
SLEEP(0x2600); //Give the last bytes in the HW TX fifo (if any) enough time to be transmitted
HalUARTUnInitISR();
}
magicByte = SB_STACK_VALUE;
// Simulate a reset for the Application code by an absolute jump to location 0x2000.
asm("LJMP 0x2000\n");
HAL_SYSTEM_RESET();
}
}
sblExec();
HAL_SYSTEM_RESET();
}
/**************************************************************************************************
* @fn main
*
* @brief ISR for the reset vector.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void main(void)
{
sblInit();
if (sbImgValid())
{
if (sblWait())
{
HalUARTUnInitUSB();
// Simulate a reset for the Application code by an absolute jump to location 0x2000.
asm("LJMP 0x2000\n");
HAL_SYSTEM_RESET();
}
}
sblExec();
HAL_SYSTEM_RESET();
}
/**************************************************************************************************
* @fn main
*
* @brief C-code main functionality.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void main(void)
{
vddWait(VDD_MIN_RUN);
HAL_BOARD_INIT();
// make sure the DMA channel is selected before we attempt to
// to write anything to flash.
sblInit();
if (sbImgValid())
{
if ((SB_UART_DELAY == 0) || ResetWasWatchDog)
{
sblJump();
}
sblWait();
}
vddWait(VDD_MIN_NV);
sblExec();
HAL_SYSTEM_RESET();
}
/**************************************************************************************************
* @fn main
*
* @brief C-code main functionality.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void main(void)
{
vddWait(VDD_MIN_RUN);
HAL_BOARD_INIT();
if (sbImgValid())
{
if ((SB_UART_DELAY == 0) || ResetWasWatchDog)
{
sblJump();
}
sblInit();
sblWait();
}
else
{
sblInit();
}
vddWait(VDD_MIN_NV);
sblExec();
HAL_SYSTEM_RESET();
}
/**************************************************************************************************
* @fn main
*
* @brief C-code main functionality.
*
* input parameters
*
* None.
*
* output parameters
*
* None.
*
* @return None.
**************************************************************************************************
*/
void main(void)
{
uint8 time_spent_validating;
uint8 bootloaderForcedByMainApp = FALSE;
uint32 mainAppCommandLocal = mainAppCommand;
vddWait(VDD_MIN_RUN);
mainAppCommand = MAIN_APP_CMD_NONE;
if (mainAppCommandLocal == MAIN_APP_CMD_FORCE_BOOTLOADER)
{
bootloaderForcedByMainApp = TRUE;
}
else if ((mainAppCommandLocal == MAIN_APP_CMD_PASS_THROUGH) || ((SLEEPSTA & LRESET) == RESETWD))
{
// If reset due to WatchDog Timer - Transfer control to the main application immediately.
// WatchDog Timer reset causes the hardware to disconnect the USB. Withought this jump here,
// the SBL code will try to initiaize the CDC too early, which causes undesired behavior on the host
// (e.g. on beaglebone black - the host gets stuck)
asm("LJMP 0x2000\n");
}
sblInit(bootloaderForcedByMainApp);
HAL_TURN_ON_LED1();
HAL_TURN_ON_LED2();
if ((!bootloaderForcedByMainApp) && (sbImgValid(&time_spent_validating)))
{
HAL_TURN_OFF_LED2();
if (sblWait(SBL_WAIT_TIME > time_spent_validating ? SBL_WAIT_TIME - time_spent_validating : 0))
{
HAL_TURN_OFF_LED1();
sbReportState(SB_STATE_EXECUTING_IMAGE);
while(sblIsUartTxPending())
{
sbUartPoll();
}
SLEEP(0x2600); //Give the last bytes in the HW TX fifo (if any) enough time to be transmitted
while (SB1_PRESS || SB2_PRESS);
sblUnInit();
// Simulate a reset for the Application code by an absolute jump to location 0x2000.
asm("LJMP 0x2000\n");
}
}
HAL_TURN_OFF_LED1();
HAL_TURN_ON_LED2();
vddWait(VDD_MIN_NV);
sblExec();
sblUnInit();
asm("LJMP 0x2000\n");
}
