void send_dimmer_status(void)
{
UART_PUTS("Sending Dimmer Status:\r\n");
// set device ID
bufx[0] = device_id;
// update packet counter
packetcounter++;
if (packetcounter % PACKET_COUNTER_WRITE_CYCLE == 0)
{
eeprom_write_dword((uint32_t*)0, packetcounter);
}
setBuf32(1, packetcounter);
// set command ID "Dimmer Status"
bufx[5] = 30; // TODO: Move command IDs to global definition file as defines
// set current brightness
bufx[6] = (uint8_t)(current_brightness * 255 / 100);
// set end brightness
bufx[7] = end_brightness;
// set total animation time
setBuf16(8, (uint16_t)(animation_length * ANIMATION_CYCLE_MS / 1000));
// set time until animation finishes
setBuf16(10, (uint16_t)((animation_length - animation_position) * ANIMATION_CYCLE_MS / 1000));
// set CRC32
uint32_t crc = crc32(bufx, 12);
setBuf32(12, crc);
// show info
UART_PUTF("CRC32: %lx\r\n", crc);
uart_putstr("Unencrypted: ");
printbytearray(bufx, 16);
rfm12_sendbuf();
UART_PUTS("Send encrypted: ");
printbytearray(bufx, 16);
UART_PUTS("\r\n");
}
void send_packet(uint8_t aes_key_nr, uint8_t data_len)
{
// set device ID (base station has ID 0 by definition)
bufx[0] = 0;
// update packet counter
packetcounter++;
if (packetcounter % PACKET_COUNTER_WRITE_CYCLE == 0)
{
eeprom_write_dword((uint32_t*)0, packetcounter);
}
setBuf32(1, packetcounter);
// set CRC32
uint32_t crc = crc32(bufx, data_len + 6);
setBuf32(data_len + 6, crc);
// load AES key (0 is first AES key)
if (aes_key_nr >= AES_KEY_EEPROM_COUNT)
{
aes_key_nr = AES_KEY_EEPROM_COUNT - 1;
}
eeprom_read_block (aes_key, (uint8_t *)(EEPROM_POS_AES_KEY + aes_key_nr * 32), 32);
// show info
decode_data(data_len + 6);
UART_PUTF(" AES key: %u\r\n", aes_key_nr);
UART_PUTF(" CRC32: %02lx\r\n", crc);
UART_PUTS(" Unencrypted: ");
printbytearray(bufx, data_len + 10);
// encrypt and send
uint8_t aes_byte_count = rfm12_sendbuf(data_len + 10);
UART_PUTS("Send encrypted: ");
printbytearray(bufx, aes_byte_count);
UART_PUTS("\r\n");
}
int main(void)
{
uint16_t send_status_timeout = 25;
uint32_t station_packetcounter;
uint32_t pos;
uint8_t button_state = 0;
uint8_t manual_dim_direction = 0;
// delay 1s to avoid further communication with uart or RFM12 when my programmer resets the MC after 500ms...
_delay_ms(1000);
util_init();
check_eeprom_compatibility(DEVICE_TYPE_DIMMER);
osccal_init();
// read packetcounter, increase by cycle and write back
packetcounter = eeprom_read_dword((uint32_t*)EEPROM_POS_PACKET_COUNTER) + PACKET_COUNTER_WRITE_CYCLE;
eeprom_write_dword((uint32_t*)EEPROM_POS_PACKET_COUNTER, packetcounter);
// read device id and write to send buffer
device_id = eeprom_read_byte((uint8_t*)EEPROM_POS_DEVICE_ID);
use_pwm_translation = 1; //eeprom_read_byte((uint8_t*)EEPROM_POS_USE_PWM_TRANSLATION);
// TODO: read (saved) dimmer state from before the eventual powerloss
/*for (i = 0; i < SWITCH_COUNT; i++)
{
uint16_t u16 = eeprom_read_word((uint16_t*)EEPROM_POS_SWITCH_STATE + i * 2);
switch_state[i] = (uint8_t)(u16 & 0b1);
switch_timeout[i] = u16 >> 1;
}*/
// read last received station packetcounter
station_packetcounter = eeprom_read_dword((uint32_t*)EEPROM_POS_STATION_PACKET_COUNTER);
led_blink(200, 200, 5);
#ifdef UART_DEBUG
uart_init(false);
UART_PUTS ("\r\n");
UART_PUTS ("smarthomatic Dimmer V1.0 (c) 2013 Uwe Freese, www.smarthomatic.org\r\n");
osccal_info();
UART_PUTF ("Device ID: %u\r\n", device_id);
UART_PUTF ("Packet counter: %lu\r\n", packetcounter);
UART_PUTF ("Use PWM translation table: %u\r\n", use_pwm_translation);
UART_PUTF ("Last received station packet counter: %u\r\n\r\n", station_packetcounter);
#endif
// init AES key
eeprom_read_block (aes_key, (uint8_t *)EEPROM_POS_AES_KEY, 32);
rfm12_init();
PWM_init();
io_init();
setPWMDutyCycle(0);
timer0_init();
// DEMO to measure the voltages of different PWM settings to calculate the pwm_lookup table
/*while (42)
{
uint16_t i;
for (i = 0; i <= 1024; i = i + 100)
{
UART_PUTF ("PWM value OCR1A: %u\r\n", i);
OCR1A = i;
led_blink(500, 6500, 1);
}
}*/
// DEMO 0..100..0%, using the pwm_lookup table and the translation table in EEPROM.
/*while (42)
{
float i;
for (i = 0; i <= 100; i = i + 0.05)
{
led_blink(10, 10, 1);
setPWMDutyCycle(i);
}
for (i = 99.95; i > 0; i = i - 0.05)
{
led_blink(10, 10, 1);
setPWMDutyCycle(i);
}
}*/
// set initial switch state
/*for (i = 0; i < SWITCH_COUNT; i++)
{
switchRelais(i, switch_state[i]);
}*/
sei();
// DEMO 30s
/*animation_length = 30;
animation_length = (uint32_t)((float)animation_length * 1000 / ANIMATION_CYCLE_MS);
start_brightness = 0;
end_brightness = 255;
animation_position = 0;*/
while (42)
{
if (rfm12_rx_status() == STATUS_COMPLETE)
{
uint8_t len = rfm12_rx_len();
if ((len == 0) || (len % 16 != 0))
{
UART_PUTF("Received garbage (%u bytes not multiple of 16): ", len);
printbytearray(bufx, len);
}
else // try to decrypt with all keys stored in EEPROM
{
memcpy(bufx, rfm12_rx_buffer(), len);
//UART_PUTS("Before decryption: ");
//printbytearray(bufx, len);
aes256_decrypt_cbc(bufx, len);
//UART_PUTS("Decrypted bytes: ");
//printbytearray(bufx, len);
uint32_t assumed_crc = getBuf32(len - 4);
uint32_t actual_crc = crc32(bufx, len - 4);
//UART_PUTF("Received CRC32 would be %lx\r\n", assumed_crc);
//UART_PUTF("Re-calculated CRC32 is %lx\r\n", actual_crc);
if (assumed_crc != actual_crc)
{
UART_PUTS("Received garbage (CRC wrong after decryption).\r\n");
}
else
{
//UART_PUTS("CRC correct, AES key found!\r\n");
UART_PUTS(" Received: ");
printbytearray(bufx, len - 4);
// decode command and react
uint8_t sender = bufx[0];
UART_PUTF(" Sender: %u\r\n", sender);
if (sender != 0)
{
UART_PUTF("Packet not from base station. Ignoring (Sender ID was: %u).\r\n", sender);
}
else
{
uint32_t packcnt = getBuf32(1);
UART_PUTF(" Packet Counter: %lu\r\n", packcnt);
// check received counter
if (0) //packcnt <= station_packetcounter)
{
UART_PUTF2("Received packet counter %lu is lower than last received counter %lu. Ignoring packet.\r\n", packcnt, station_packetcounter);
}
else
{
// write received counter
station_packetcounter = packcnt;
eeprom_write_dword((uint32_t*)EEPROM_POS_STATION_PACKET_COUNTER, station_packetcounter);
// check command ID
uint8_t cmd = bufx[5];
UART_PUTF(" Command ID: %u\r\n", cmd);
if (cmd != 141) // ID 141 == Dimmer Request
{
UART_PUTF("Received unknown command ID %u. Ignoring packet.\r\n", cmd);
}
else
{
// check device id
uint8_t rcv_id = bufx[6];
UART_PUTF(" Receiver ID: %u\r\n", rcv_id);
if (rcv_id != device_id)
{
UART_PUTF("Device ID %u does not match. Ignoring packet.\r\n", rcv_id);
}
else
{
// read animation mode and parameters
uint8_t animation_mode = bufx[7] >> 5;
// TODO: Implement support for multiple dimmers (e.g. RGB)
// uint8_t dimmer_bitmask = bufx[7] & 0b111;
animation_length = getBuf16(8);
start_brightness = bufx[10];
end_brightness = bufx[11];
UART_PUTF(" Animation Mode: %u\r\n", animation_mode); // TODO: Set binary mode like 00010110
//UART_PUTF(" Dimmer Bitmask: %u\r\n", dimmer_bitmask);
UART_PUTF(" Animation Time: %us\r\n", animation_length);
UART_PUTF(" Start Brightness: %u\r\n", start_brightness);
UART_PUTF(" End Brightness: %u\r\n", end_brightness);
animation_length = (uint32_t)((float)animation_length * 1000 / ANIMATION_CYCLE_MS);
animation_position = 0;
/* TODO: Write to EEPROM (?)
// write back switch state to EEPROM
switch_state[i] = req_state;
switch_timeout[i] = req_timeout;
eeprom_write_word((uint16_t*)EEPROM_POS_SWITCH_STATE + i * 2, u16);
*/
// send acknowledge
UART_PUTS("Sending ACK:\r\n");
// set device ID (base station has ID 0 by definition)
bufx[0] = device_id;
// update packet counter
packetcounter++;
if (packetcounter % PACKET_COUNTER_WRITE_CYCLE == 0)
{
eeprom_write_dword((uint32_t*)0, packetcounter);
}
setBuf32(1, packetcounter);
// set command ID "Generic Acknowledge"
bufx[5] = 1;
// set sender ID of request
bufx[6] = sender;
// set Packet counter of request
setBuf32(7, station_packetcounter);
// zero unused bytes
bufx[11] = 0;
// set CRC32
uint32_t crc = crc32(bufx, 12);
setBuf32(12, crc);
// show info
UART_PUTF(" CRC32: %lx\r\n", crc);
uart_putstr(" Unencrypted: ");
printbytearray(bufx, 16);
rfm12_sendbuf();
UART_PUTS(" Send encrypted: ");
printbytearray(bufx, 16);
UART_PUTS("\r\n");
rfm12_tick();
led_blink(200, 0, 1);
send_status_timeout = 25;
}
}
}
}
}
}
// tell the implementation that the buffer can be reused for the next data.
rfm12_rx_clear();
}
_delay_ms(ANIMATION_UPDATE_MS);
// React on button press.
// - abort animation
// - switch off, when brightness > 0
// - switch on otherwise
if (!(BUTTON_PORT & (1 << BUTTON_PIN))) // button press
{
if (button_state == 0)
{
UART_PUTS("Button pressed\r\n");
animation_length = 0;
animation_position = 0;
}
if (button_state < 5)
{
button_state++;
}
else // manual dimming
{
if (manual_dim_direction) // UP
{
if (current_brightness < 100)
{
current_brightness = (uint8_t)current_brightness / 2 * 2 + 2;
setPWMDutyCycle(current_brightness);
}
else
{
UART_PUTS("manual dimming DOWN\r\n");
manual_dim_direction = 0;
}
}
else // DOWN
{
if (current_brightness > 0)
{
current_brightness = (((uint8_t)current_brightness - 1) / 2) * 2;
setPWMDutyCycle(current_brightness);
}
else
{
UART_PUTS("manual dimming UP\r\n");
manual_dim_direction = 1;
}
}
}
}
else if (button_state && (BUTTON_PORT & (1 << BUTTON_PIN))) // button release
{
UART_PUTS("Button released\r\n");
if (button_state < 5) // short button press
{
if (current_brightness > 0)
{
UART_PUTS(" -> 0%\r\n");
setPWMDutyCycle(0);
}
else
{
UART_PUTS(" -> 100%\r\n");
setPWMDutyCycle(100);
}
}
else
{
// reverse dim direction
manual_dim_direction = !manual_dim_direction;
}
button_state = 0;
}
// update brightness according animation_position, updated by timer0
if (animation_length > 0)
{
pos = animation_position; // copy value to avoid that it changes in between by timer interrupt
UART_PUTF2("%lu/%lu, ", pos, animation_length);
if (pos == animation_length)
{
UART_PUTF("END Brightness %u%%, ", end_brightness * 100 / 255);
setPWMDutyCycle((float)end_brightness * 100 / 255);
animation_length = 0;
animation_position = 0;
}
else
{
float brightness = (start_brightness + ((float)end_brightness - start_brightness) * pos / animation_length) * 100 / 255;
UART_PUTF("Br.%u%%, ", (uint32_t)(brightness));
setPWMDutyCycle(brightness);
}
}
// send status from time to time
if (send_status_timeout == 0)
{
send_status_timeout = SEND_STATUS_EVERY_SEC * (1000 / ANIMATION_UPDATE_MS);
send_dimmer_status();
led_blink(200, 0, 1);
}
rfm12_tick();
send_status_timeout--;
checkSwitchOff();
}