void stm32_boardinitialize(void)
{
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
* stm32_spiinitialize() has been brought into the link.
*/
#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2) || defined(CONFIG_STM32_SPI3)
if (stm32_spiinitialize)
{
stm32_spiinitialize();
}
#endif
/* Initialize USB if the 1) USB device controller is in the configuration and 2)
* disabled, and 3) the weak function stm32_usbinitialize() has been brought
* into the build. Presumeably either CONFIG_USBDEV is also selected.
*/
#ifdef CONFIG_STM32_USB
if (stm32_usbinitialize)
{
stm32_usbinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
__END_DECLS
/****************************************************************************
* Protected Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
__EXPORT void stm32_boardinitialize(void)
{
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs (empty call to NuttX' ledinit) */
up_ledinit();
}
void lpc17_boardinitialize(void)
{
/* Enable +5V needed for CAN */
#if defined(CONFIG_LPC17_CAN1) || defined(CONFIG_LPC17_CAN2)
lpc17_configgpio(NUCLEUS2G_5V_ENABLE);
#else
lpc17_configgpio(NUCLEUS2G_5V_DISABLE);
#endif
/* If UART0 is used, enabled the MAX232 driver */
#ifdef CONFIG_LPC17_UART0
lpc17_configgpio(NUCLEUS2G_232_ENABLE);
#else
lpc17_configgpio(NUCLEUS2G_232_POWERSAVE);
#endif
/* Configure SSP chip selects if 1) at least one SSP is enabled, and 2) the weak
* function lpc17_sspinitialize() has been brought into the link.
*/
#if defined(CONFIG_LPC17_SSP0) || defined(CONFIG_LPC17_SSP1)
if (lpc17_sspinitialize)
{
lpc17_sspinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
void lm3s_boardinitialize(void)
{
/* Configure SPI chip selects if 1) SSI is not disabled, and 2) the weak function
* lm3s_ssiinitialize() has been brought into the link.
*/
#if !defined(CONFIG_SSI0_DISABLE)
if (lm3s_ssiinitialize)
{
lm3s_ssiinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
/* Configure serial transciever */
lm3s_configgpio(XCVR_INV_GPIO);
lm3s_configgpio(XCVR_ENA_GPIO);
lm3s_configgpio(XCVR_ON_GPIO);
lm3s_configgpio(XCVR_OFF_GPIO);
}
void stm32_boardinitialize(void)
{
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
* stm32_spiinitialize() has been brought into the link.
*/
#if defined(CONFIG_STM32_SPI1) || defined(CONFIG_STM32_SPI2)
if (stm32_spiinitialize)
{
stm32_spiinitialize();
}
#endif
/* Initialize USB is 1) USBDEV is selected, 2) the USB controller is not
* disabled, and 3) the weak function stm32_usbinitialize() has been brought
* into the build.
*/
#if defined(CONFIG_USBDEV) && defined(CONFIG_STM32_USB)
if (stm32_usbinitialize)
{
stm32_usbinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
__EXPORT void stm32_boardinitialize(void)
{
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs */
up_ledinit();
}
void up_boardinitialize(void)
{
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
__END_DECLS
/****************************************************************************
* Protected Functions
****************************************************************************/
/****************************************************************************
* Public Functions
****************************************************************************/
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
__EXPORT void stm32_boardinitialize(void)
{
/* Hold power state */
board_pwr_init(0);
/* TEMP ctrl Off (active high, init is clear) */
stm32_configgpio(GPIO_TEMP_CONT);
/* Select 0 */
stm32_configgpio(GPIO_S0);
stm32_configgpio(GPIO_S1);
stm32_configgpio(GPIO_S2);
/* Radio Off (active low, init is set) */
stm32_configgpio(GPIO_PCON_RADIO);
/* configure always-on ADC pins */
stm32_configgpio(GPIO_ADC1_IN10);
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs (empty call to NuttX' ledinit) */
up_ledinit();
}
__EXPORT void
stm32_boardinitialize(void)
{
stm32_configgpio(GPIO_FORCE_BOOTLOADER);
_bootloader_force_pin_callback(0, NULL);
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs */
up_ledinit();
}
void lpc313x_boardinitialize(void)
{
/* Initialize configured, external memory resources */
#ifdef CONFIG_LPC313X_EXTSDRAM
lpc313x_meminitialize();
#endif
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
* lpc313x_spiinitialize() has been brought into the link.
*/
#if defined(CONFIG_LPC313X_SPI)
if (lpc313x_spiinitialize)
{
lpc313x_spiinitialize();
}
#endif
/* Initialize USB is 1) USBDEV is selected, 2) the USB controller is not
* disabled, and 3) the weak function lpc313x_usbinitialize() has been brought
* into the build.
*/
#if defined(CONFIG_USBDEV) && defined(CONFIG_LPC313X_USB)
if (lpc313x_usbinitialize)
{
lpc313x_usbinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
/* Set up mass storage device to support on demand paging */
#if defined(CONFIG_PAGING)
if (lpc313x_pginitialize)
{
lpc313x_pginitialize();
}
#endif
}
void sam_boardinitialize(void)
{
/* Configure SPI chip selects if 1) SPI is not disabled, and 2) the weak function
* sam_spiinitialize() has been brought into the link.
*/
#ifdef CONFIG_SAM34_SPI0
if (sam_spiinitialize)
{
sam_spiinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
void lpc17_boardinitialize(void)
{
/* Configure SSP chip selects if 1) at least one SSP is enabled, and 2) the weak
* function lpc17_sspinitialize() has been brought into the link.
*/
#if defined(CONFIG_LPC17_SSP0) || defined(CONFIG_LPC17_SSP1)
if (lpc17_sspinitialize)
{
lpc17_sspinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
void lm_boardinitialize(void)
{
/* Configure chip selects if 1) SSI is not disabled, and 2) the weak function
* lm_ssiinitialize() has been brought into the link.
*/
#if !defined(CONFIG_SSI0_DISABLE) || !defined(CONFIG_SSI1_DISABLE)
if (lm_ssiinitialize)
{
lm_ssiinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
void lm3s_boardinitialize(void)
{
/* Configure SPI chip selects if 1) SSI is not disabled, and 2) the weak function
* lm3s_ssiinitialize() has been brought into the link.
*/
/* The Eagle100 microSD CS is on SSI0 */
#if !defined(CONFIG_SSI0_DISABLE) /* || !defined(CONFIG_SSI1_DISABLE) */
if (lm3s_ssiinitialize)
{
lm3s_ssiinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
}
void lpc17_boardinitialize(void)
{
/* Initialize the EMC, SDRAM, NOR FLASH, and NAND FLASH */
#ifdef CONFIG_LPC17_EMC
lpc17_emcinitialize();
#ifdef CONFIG_ARCH_EXTDRAM
open1788_sdram_initialize();
#endif
#ifdef CONFIG_ARCH_EXTNOR
open1788_nor_initialize();
#endif
#ifdef CONFIG_ARCH_EXTNAND
open1788_nand_initialize();
#endif
#endif
/* Configure SSP chip selects if 1) at least one SSP is enabled, and 2) the weak
* function open1788_sspinitialize() has been brought into the link.
*/
#if defined(CONFIG_LPC17_SSP0) || defined(CONFIG_LPC17_SSP1) || defined(CONFIG_LPC17_SSP2)
if (open1788_sspinitialize)
{
open1788_sspinitialize();
}
#endif
/* Configure on-board LEDs if LED support has been selected. */
#ifdef CONFIG_ARCH_LEDS
up_ledinit();
#endif
/* Configure the LCD GPIOs if LCD support has been selected. */
#ifdef CONFIG_LPC17_LCD
open1788_lcd_initialize();
#endif
}
__EXPORT void
kinetis_boardinitialize(void)
{
/* configure LEDs */
up_ledinit();
}
__END_DECLS
/****************************************************************************
* Protected Functions
****************************************************************************/
#if defined(CONFIG_FAT_DMAMEMORY)
/****************************************************************************
* Public Functions
****************************************************************************/
#else
# define dma_alloc_init()
#endif
/************************************************************************************
* Name: stm32_boardinitialize
*
* Description:
* All STM32 architectures must provide the following entry point. This entry point
* is called early in the initialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
__EXPORT void
stm32_boardinitialize(void)
{
/* configure SPI interfaces */
stm32_spiinitialize();
/* configure LEDs */
up_ledinit();
}