/* set up the ULPI USB controller with the parameters provided */
static int init_ulpi_usb_controller(struct fdt_usb *config,
struct usb_ctlr *usbctlr)
{
u32 val;
int loop_count;
struct ulpi_viewport ulpi_vp;
/* set up ULPI reference clock on pllp_out4 */
clock_enable(PERIPH_ID_DEV2_OUT);
clock_set_pllout(CLOCK_ID_PERIPH, PLL_OUT4, CONFIG_ULPI_REF_CLK);
/* reset ULPI phy */
if (fdt_gpio_isvalid(&config->phy_reset_gpio)) {
fdtdec_setup_gpio(&config->phy_reset_gpio);
gpio_direction_output(config->phy_reset_gpio.gpio, 0);
mdelay(5);
gpio_set_value(config->phy_reset_gpio.gpio, 1);
}
/* Reset the usb controller */
clock_enable(config->periph_id);
usbf_reset_controller(config, usbctlr);
/* enable pinmux bypass */
setbits_le32(&usbctlr->ulpi_timing_ctrl_0,
ULPI_CLKOUT_PINMUX_BYP | ULPI_OUTPUT_PINMUX_BYP);
/* Select ULPI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, PTS_ULPI << PTS_SHIFT);
/* enable ULPI transceiver */
setbits_le32(&usbctlr->susp_ctrl, ULPI_PHY_ENB);
/* configure ULPI transceiver timings */
val = 0;
writel(val, &usbctlr->ulpi_timing_ctrl_1);
val |= ULPI_DATA_TRIMMER_SEL(4);
val |= ULPI_STPDIRNXT_TRIMMER_SEL(4);
val |= ULPI_DIR_TRIMMER_SEL(4);
writel(val, &usbctlr->ulpi_timing_ctrl_1);
udelay(10);
val |= ULPI_DATA_TRIMMER_LOAD;
val |= ULPI_STPDIRNXT_TRIMMER_LOAD;
val |= ULPI_DIR_TRIMMER_LOAD;
writel(val, &usbctlr->ulpi_timing_ctrl_1);
/* set up phy for host operation with external vbus supply */
ulpi_vp.port_num = 0;
ulpi_vp.viewport_addr = (u32)&usbctlr->ulpi_viewport;
if (ulpi_init(&ulpi_vp)) {
printf("Tegra ULPI viewport init failed\n");
return -1;
}
ulpi_set_vbus(&ulpi_vp, 1, 1);
ulpi_set_vbus_indicator(&ulpi_vp, 1, 1, 0);
/* enable wakeup events */
setbits_le32(&usbctlr->port_sc1, WKCN | WKDS | WKOC);
/* Enable and wait for the phy clock to become valid in 100 ms */
setbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
for (loop_count = 100000; loop_count != 0; loop_count--) {
if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
break;
udelay(1);
}
if (!loop_count)
return -1;
clrbits_le32(&usbctlr->susp_ctrl, USB_SUSP_CLR);
return 0;
}
/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config,
struct usb_ctlr *usbctlr, const u32 timing[])
{
u32 val;
int loop_count;
clock_enable(config->periph_id);
/* Reset the usb controller */
usbf_reset_controller(config, usbctlr);
/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
/* Follow the crystal clock disable by >100ns delay */
udelay(1);
/*
* To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
* mux must be switched to actually use a_sess_vld threshold.
*/
if (fdt_gpio_isvalid(&config->vbus_gpio)) {
clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
VBUS_SENSE_CTL_MASK,
VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);
}
/*
* PLL Delay CONFIGURATION settings. The following parameters control
* the bring up of the plls.
*/
val = readl(&usbctlr->utmip_misc_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
timing[PARAM_STABLE_COUNT] << UTMIP_PLLU_STABLE_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
timing[PARAM_ACTIVE_DELAY_COUNT] <<
UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
writel(val, &usbctlr->utmip_misc_cfg1);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&usbctlr->utmip_pll_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
timing[PARAM_ENABLE_DELAY_COUNT] <<
UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
timing[PARAM_XTAL_FREQ_COUNT] <<
UTMIP_XTAL_FREQ_COUNT_SHIFT);
writel(val, &usbctlr->utmip_pll_cfg1);
/* Setting the tracking length time */
clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
UTMIP_BIAS_PDTRK_COUNT_MASK,
timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);
/* Program debounce time for VBUS to become valid */
clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
UTMIP_DEBOUNCE_CFG0_MASK,
timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);
setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J);
/* Disable battery charge enabling bit */
setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG);
clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE);
setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL);
/*
* Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
* Setting these fields, together with default values of the
* other fields, results in programming the registers below as
* follows:
* UTMIP_HSRX_CFG0 = 0x9168c000
* UTMIP_HSRX_CFG1 = 0x13
*/
/* Set PLL enable delay count and Crystal frequency count */
val = readl(&usbctlr->utmip_hsrx_cfg0);
clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK,
utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT);
clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK,
utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT);
writel(val, &usbctlr->utmip_hsrx_cfg0);
/* Configure the UTMIP_HS_SYNC_START_DLY */
clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1,
UTMIP_HS_SYNC_START_DLY_MASK,
utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT);
/* Preceed the crystal clock disable by >100ns delay. */
udelay(1);
/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
/* Finished the per-controller init. */
/* De-assert UTMIP_RESET to bring out of reset. */
clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);
/* Wait for the phy clock to become valid in 100 ms */
for (loop_count = 100000; loop_count != 0; loop_count--) {
if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
break;
udelay(1);
}
if (!loop_count)
return -1;
/* Disable ICUSB FS/LS transceiver */
clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
/* Select UTMI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
PTS_UTMI << PTS_SHIFT);
clrbits_le32(&usbctlr->port_sc1, STS);
/* Deassert power down state */
clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);
return 0;
}
/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config)
{
u32 val;
int loop_count;
const unsigned *timing;
struct usb_ctlr *usbctlr = config->reg;
struct clk_rst_ctlr *clkrst;
struct usb_ctlr *usb1ctlr;
clock_enable(config->periph_id);
/* Reset the usb controller */
usbf_reset_controller(config, usbctlr);
/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
/* Follow the crystal clock disable by >100ns delay */
udelay(1);
/*
* To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
* mux must be switched to actually use a_sess_vld threshold.
*/
if (config->dr_mode == DR_MODE_OTG &&
fdt_gpio_isvalid(&config->vbus_gpio))
clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
VBUS_SENSE_CTL_MASK,
VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);
/*
* PLL Delay CONFIGURATION settings. The following parameters control
* the bring up of the plls.
*/
timing = get_pll_timing();
if (!controller->has_hostpc) {
val = readl(&usbctlr->utmip_misc_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
timing[PARAM_STABLE_COUNT] <<
UTMIP_PLLU_STABLE_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
timing[PARAM_ACTIVE_DELAY_COUNT] <<
UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
writel(val, &usbctlr->utmip_misc_cfg1);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&usbctlr->utmip_pll_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
timing[PARAM_ENABLE_DELAY_COUNT] <<
UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
timing[PARAM_XTAL_FREQ_COUNT] <<
UTMIP_XTAL_FREQ_COUNT_SHIFT);
writel(val, &usbctlr->utmip_pll_cfg1);
} else {
clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
val = readl(&clkrst->crc_utmip_pll_cfg2);
clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
timing[PARAM_STABLE_COUNT] <<
UTMIP_PLLU_STABLE_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
timing[PARAM_ACTIVE_DELAY_COUNT] <<
UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
writel(val, &clkrst->crc_utmip_pll_cfg2);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&clkrst->crc_utmip_pll_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
timing[PARAM_ENABLE_DELAY_COUNT] <<
UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
timing[PARAM_XTAL_FREQ_COUNT] <<
UTMIP_XTAL_FREQ_COUNT_SHIFT);
writel(val, &clkrst->crc_utmip_pll_cfg1);
/* Disable Power Down state for PLL */
clrbits_le32(&clkrst->crc_utmip_pll_cfg1,
PLLU_POWERDOWN | PLL_ENABLE_POWERDOWN |
PLL_ACTIVE_POWERDOWN);
/* Recommended PHY settings for EYE diagram */
val = readl(&usbctlr->utmip_xcvr_cfg0);
clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MASK,
0x4 << UTMIP_XCVR_SETUP_SHIFT);
clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MSB_MASK,
0x3 << UTMIP_XCVR_SETUP_MSB_SHIFT);
clrsetbits_le32(&val, UTMIP_XCVR_HSSLEW_MSB_MASK,
0x8 << UTMIP_XCVR_HSSLEW_MSB_SHIFT);
writel(val, &usbctlr->utmip_xcvr_cfg0);
clrsetbits_le32(&usbctlr->utmip_xcvr_cfg1,
UTMIP_XCVR_TERM_RANGE_ADJ_MASK,
0x7 << UTMIP_XCVR_TERM_RANGE_ADJ_SHIFT);
/* Some registers can be controlled from USB1 only. */
if (config->periph_id != PERIPH_ID_USBD) {
clock_enable(PERIPH_ID_USBD);
/* Disable Reset if in Reset state */
reset_set_enable(PERIPH_ID_USBD, 0);
}
usb1ctlr = (struct usb_ctlr *)
((u32)config->reg & USB1_ADDR_MASK);
val = readl(&usb1ctlr->utmip_bias_cfg0);
setbits_le32(&val, UTMIP_HSDISCON_LEVEL_MSB);
clrsetbits_le32(&val, UTMIP_HSDISCON_LEVEL_MASK,
0x1 << UTMIP_HSDISCON_LEVEL_SHIFT);
clrsetbits_le32(&val, UTMIP_HSSQUELCH_LEVEL_MASK,
0x2 << UTMIP_HSSQUELCH_LEVEL_SHIFT);
writel(val, &usb1ctlr->utmip_bias_cfg0);
/* Miscellaneous setting mentioned in Programming Guide */
clrbits_le32(&usbctlr->utmip_misc_cfg0,
UTMIP_SUSPEND_EXIT_ON_EDGE);
}
/* Setting the tracking length time */
clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
UTMIP_BIAS_PDTRK_COUNT_MASK,
timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);
/* Program debounce time for VBUS to become valid */
clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
UTMIP_DEBOUNCE_CFG0_MASK,
timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);
setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J);
/* Disable battery charge enabling bit */
setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG);
clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE);
setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL);
/*
* Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
* Setting these fields, together with default values of the
* other fields, results in programming the registers below as
* follows:
* UTMIP_HSRX_CFG0 = 0x9168c000
* UTMIP_HSRX_CFG1 = 0x13
*/
/* Set PLL enable delay count and Crystal frequency count */
val = readl(&usbctlr->utmip_hsrx_cfg0);
clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK,
utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT);
clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK,
utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT);
writel(val, &usbctlr->utmip_hsrx_cfg0);
/* Configure the UTMIP_HS_SYNC_START_DLY */
clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1,
UTMIP_HS_SYNC_START_DLY_MASK,
utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT);
/* Preceed the crystal clock disable by >100ns delay. */
udelay(1);
/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
if (controller->has_hostpc) {
if (config->periph_id == PERIPH_ID_USBD)
clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
UTMIP_FORCE_PD_SAMP_A_POWERDOWN);
if (config->periph_id == PERIPH_ID_USB3)
clrbits_le32(&clkrst->crc_utmip_pll_cfg2,
UTMIP_FORCE_PD_SAMP_C_POWERDOWN);
}
/* Finished the per-controller init. */
/* De-assert UTMIP_RESET to bring out of reset. */
clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET);
/* Wait for the phy clock to become valid in 100 ms */
for (loop_count = 100000; loop_count != 0; loop_count--) {
if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID)
break;
udelay(1);
}
if (!loop_count)
return -1;
/* Disable ICUSB FS/LS transceiver */
clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1);
/* Select UTMI parallel interface */
clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK,
PTS_UTMI << PTS_SHIFT);
clrbits_le32(&usbctlr->port_sc1, STS);
/* Deassert power down state */
clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN |
UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN);
clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN |
UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN);
if (controller->has_hostpc) {
/*
* BIAS Pad Power Down is common among all 3 USB
* controllers and can be controlled from USB1 only.
*/
usb1ctlr = (struct usb_ctlr *)
((u32)config->reg & USB1_ADDR_MASK);
clrbits_le32(&usb1ctlr->utmip_bias_cfg0, UTMIP_BIASPD);
udelay(25);
clrbits_le32(&usb1ctlr->utmip_bias_cfg1,
UTMIP_FORCE_PDTRK_POWERDOWN);
}
return 0;
}
/* set up the UTMI USB controller with the parameters provided */
static int init_utmi_usb_controller(struct fdt_usb *config,
enum usb_init_type init)
{
struct fdt_usb_controller *controller;
u32 b_sess_valid_mask, val;
int loop_count;
const unsigned *timing;
struct usb_ctlr *usbctlr = config->reg;
struct clk_rst_ctlr *clkrst;
struct usb_ctlr *usb1ctlr;
clock_enable(config->periph_id);
/* Reset the usb controller */
usbf_reset_controller(config, usbctlr);
/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN);
/* Follow the crystal clock disable by >100ns delay */
udelay(1);
b_sess_valid_mask = (VBUS_B_SESS_VLD_SW_VALUE | VBUS_B_SESS_VLD_SW_EN);
clrsetbits_le32(&usbctlr->phy_vbus_sensors, b_sess_valid_mask,
(init == USB_INIT_DEVICE) ? b_sess_valid_mask : 0);
/*
* To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
* mux must be switched to actually use a_sess_vld threshold.
*/
if (config->dr_mode == DR_MODE_OTG &&
dm_gpio_is_valid(&config->vbus_gpio))
clrsetbits_le32(&usbctlr->usb1_legacy_ctrl,
VBUS_SENSE_CTL_MASK,
VBUS_SENSE_CTL_A_SESS_VLD << VBUS_SENSE_CTL_SHIFT);
controller = &fdt_usb_controllers[config->type];
debug("controller=%p, type=%d\n", controller, config->type);
/*
* PLL Delay CONFIGURATION settings. The following parameters control
* the bring up of the plls.
*/
timing = get_pll_timing(controller);
if (!controller->has_hostpc) {
val = readl(&usbctlr->utmip_misc_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
timing[PARAM_STABLE_COUNT] <<
UTMIP_PLLU_STABLE_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
timing[PARAM_ACTIVE_DELAY_COUNT] <<
UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
writel(val, &usbctlr->utmip_misc_cfg1);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&usbctlr->utmip_pll_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
timing[PARAM_ENABLE_DELAY_COUNT] <<
UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
timing[PARAM_XTAL_FREQ_COUNT] <<
UTMIP_XTAL_FREQ_COUNT_SHIFT);
writel(val, &usbctlr->utmip_pll_cfg1);
} else {
clkrst = (struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
val = readl(&clkrst->crc_utmip_pll_cfg2);
clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK,
timing[PARAM_STABLE_COUNT] <<
UTMIP_PLLU_STABLE_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK,
timing[PARAM_ACTIVE_DELAY_COUNT] <<
UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT);
writel(val, &clkrst->crc_utmip_pll_cfg2);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&clkrst->crc_utmip_pll_cfg1);
clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK,
timing[PARAM_ENABLE_DELAY_COUNT] <<
UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT);
clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK,
timing[PARAM_XTAL_FREQ_COUNT] <<
UTMIP_XTAL_FREQ_COUNT_SHIFT);
writel(val, &clkrst->crc_utmip_pll_cfg1);
/* Disable Power Down state for PLL */
clrbits_le32(&clkrst->crc_utmip_pll_cfg1,
PLLU_POWERDOWN | PLL_ENABLE_POWERDOWN |
PLL_ACTIVE_POWERDOWN);
/* Recommended PHY settings for EYE diagram */
val = readl(&usbctlr->utmip_xcvr_cfg0);
clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MASK,
0x4 << UTMIP_XCVR_SETUP_SHIFT);
clrsetbits_le32(&val, UTMIP_XCVR_SETUP_MSB_MASK,
0x3 << UTMIP_XCVR_SETUP_MSB_SHIFT);
clrsetbits_le32(&val, UTMIP_XCVR_HSSLEW_MSB_MASK,
0x8 << UTMIP_XCVR_HSSLEW_MSB_SHIFT);
writel(val, &usbctlr->utmip_xcvr_cfg0);
clrsetbits_le32(&usbctlr->utmip_xcvr_cfg1,
UTMIP_XCVR_TERM_RANGE_ADJ_MASK,
0x7 << UTMIP_XCVR_TERM_RANGE_ADJ_SHIFT);
/* Some registers can be controlled from USB1 only. */
if (config->periph_id != PERIPH_ID_USBD) {
clock_enable(PERIPH_ID_USBD);
/* Disable Reset if in Reset state */
reset_set_enable(PERIPH_ID_USBD, 0);
}
usb1ctlr = (struct usb_ctlr *)
((unsigned long)config->reg & USB1_ADDR_MASK);
val = readl(&usb1ctlr->utmip_bias_cfg0);
setbits_le32(&val, UTMIP_HSDISCON_LEVEL_MSB);
clrsetbits_le32(&val, UTMIP_HSDISCON_LEVEL_MASK,
0x1 << UTMIP_HSDISCON_LEVEL_SHIFT);
clrsetbits_le32(&val, UTMIP_HSSQUELCH_LEVEL_MASK,
0x2 << UTMIP_HSSQUELCH_LEVEL_SHIFT);
writel(val, &usb1ctlr->utmip_bias_cfg0);
/* Miscellaneous setting mentioned in Programming Guide */
clrbits_le32(&usbctlr->utmip_misc_cfg0,
UTMIP_SUSPEND_EXIT_ON_EDGE);
}
/* Setting the tracking length time */
clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
UTMIP_BIAS_PDTRK_COUNT_MASK,
timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT);
/* Program debounce time for VBUS to become valid */
clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
UTMIP_DEBOUNCE_CFG0_MASK,
timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT);
if (timing[PARAM_DEBOUNCE_A_TIME] > 0xFFFF) {
clrsetbits_le32(&usbctlr->utmip_debounce_cfg0,
UTMIP_DEBOUNCE_CFG0_MASK,
(timing[PARAM_DEBOUNCE_A_TIME] >> 1)
<< UTMIP_DEBOUNCE_CFG0_SHIFT);
clrsetbits_le32(&usbctlr->utmip_bias_cfg1,
UTMIP_BIAS_DEBOUNCE_TIMESCALE_MASK,
1 << UTMIP_BIAS_DEBOUNCE_TIMESCALE_SHIFT);
}
/* set up the USB controller with the parameters provided */
static void init_usb_controller(enum periph_id id, struct usb_ctlr *usbctlr,
const int *params)
{
u32 val;
int loop_count;
#if defined(CONFIG_TEGRA3)
struct clk_rst_ctlr *clkrst =
(struct clk_rst_ctlr *)NV_PA_CLK_RST_BASE;
#endif
clock_enable(id);
/* Reset the usb controller */
usbf_reset_controller(id, usbctlr);
/* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */
bf_clearl(UTMIP_PHY_XTAL_CLOCKEN, &usbctlr->utmip_misc_cfg1);
/* Follow the crystal clock disable by >100ns delay */
udelay(1);
#if !defined(CONFIG_TEGRA3)
/*
* To Use the A Session Valid for cable detection logic, VBUS_WAKEUP
* mux must be switched to actually use a_sess_vld threshold.
*/
if (id == PERIPH_ID_USBD)
bf_enum_writel(VBUS_SENSE_CTL, A_SESS_VLD,
&usbctlr->usb1_legacy_ctrl);
/*
* PLL Delay CONFIGURATION settings. The following parameters control
* the bring up of the plls.
*/
val = readl(&usbctlr->utmip_misc_cfg1);
bf_update(UTMIP_PLLU_STABLE_COUNT, val, params[PARAM_STABLE_COUNT]);
bf_update(UTMIP_PLL_ACTIVE_DLY_COUNT, val,
params[PARAM_ACTIVE_DELAY_COUNT]);
writel(val, &usbctlr->utmip_misc_cfg1);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&usbctlr->utmip_pll_cfg1);
bf_update(UTMIP_PLLU_ENABLE_DLY_COUNT, val,
params[PARAM_ENABLE_DELAY_COUNT]);
bf_update(UTMIP_XTAL_FREQ_COUNT, val, params[PARAM_XTAL_FREQ_COUNT]);
writel(val, &usbctlr->utmip_pll_cfg1);
#else
/*
* PLL Delay CONFIGURATION settings. The following parameters control
* the bring up of the plls.
*/
val = readl(&clkrst->crc_pll_cfg2);
bf_update(UTMIP_PLLU_STABLE_COUNT, val, params[PARAM_STABLE_COUNT]);
bf_update(UTMIP_PLL_ACTIVE_DLY_COUNT, val,
params[PARAM_ACTIVE_DELAY_COUNT]);
writel(val, &clkrst->crc_pll_cfg2);
/* Set PLL enable delay count and crystal frequency count */
val = readl(&clkrst->crc_pll_cfg1);
bf_update(UTMIP_PLLU_ENABLE_DLY_COUNT, val,
params[PARAM_ENABLE_DELAY_COUNT]);
bf_update(UTMIP_XTAL_FREQ_COUNT, val, params[PARAM_XTAL_FREQ_COUNT]);
writel(val, &clkrst->crc_pll_cfg1);
/* Disable Power Down state for PLL */
bf_writel(UTMIP_FORCE_PLLU_POWERDOWN, 0, &clkrst->crc_pll_cfg1);
bf_writel(UTMIP_FORCE_PLL_ENABLE_POWERDOWN, 0, &clkrst->crc_pll_cfg1);
bf_writel(UTMIP_FORCE_PLL_ACTIVE_POWERDOWN, 0, &clkrst->crc_pll_cfg1);
/* Recommended PHY settings for EYE diagram */
bf_writel(UTMIP_XCVR_SETUP, 0x4, &usbctlr->utmip_xcvr_cfg0);
bf_writel(UTMIP_XCVR_SETUP_MSB, 0x3, &usbctlr->utmip_xcvr_cfg0);
bf_writel(UTMIP_XCVR_HSSLEW_MSB, 0x8, &usbctlr->utmip_xcvr_cfg0);
bf_writel(UTMIP_XCVR_TERM_RANGE_ADJ, 0x7, &usbctlr->utmip_xcvr_cfg1);
bf_writel(UTMIP_HSDISCON_LEVEL_MSB, 0x1, &usbctlr->utmip_bias_cfg0);
bf_writel(UTMIP_HSDISCON_LEVEL, 0x1, &usbctlr->utmip_bias_cfg0);
bf_writel(UTMIP_HSSQUELCH_LEVEL, 0x2, &usbctlr->utmip_bias_cfg0);
/* Miscellaneous setting mentioned in Programming Guide */
bf_writel(UTMIP_SUSPEND_EXIT_ON_EDGE, 0, &usbctlr->utmip_misc_cfg0);
#endif
/* Setting the tracking length time */
bf_writel(UTMIP_BIAS_PDTRK_COUNT, params[PARAM_BIAS_TIME],
&usbctlr->utmip_bias_cfg1);
/* Program debounce time for VBUS to become valid */
bf_writel(UTMIP_DEBOUNCE_CFG0, params[PARAM_DEBOUNCE_A_TIME],
&usbctlr->utmip_debounce_cfg0);
/* Set UTMIP_FS_PREAMBLE_J to 1 */
bf_writel(UTMIP_FS_PREAMBLE_J, 1, &usbctlr->utmip_tx_cfg0);
/* Disable battery charge enabling bit */
bf_writel(UTMIP_PD_CHRG, 1, &usbctlr->utmip_bat_chrg_cfg0);
/* Set UTMIP_XCVR_LSBIAS_SEL to 0 */
bf_writel(UTMIP_XCVR_LSBIAS_SE, 0, &usbctlr->utmip_xcvr_cfg0);
/* Set bit 3 of UTMIP_SPARE_CFG0 to 1 */
bf_writel(FUSE_SETUP_SEL, 1, &usbctlr->utmip_spare_cfg0);
/*
* Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT
* Setting these fields, together with default values of the
* other fields, results in programming the registers below as
* follows:
* UTMIP_HSRX_CFG0 = 0x9168c000
* UTMIP_HSRX_CFG1 = 0x13
*/
/* Set PLL enable delay count and Crystal frequency count */
val = readl(&usbctlr->utmip_hsrx_cfg0);
bf_update(UTMIP_IDLE_WAIT, val, utmip_idle_wait_delay);
bf_update(UTMIP_ELASTIC_LIMIT, val, utmip_elastic_limit);
writel(val, &usbctlr->utmip_hsrx_cfg0);
/* Configure the UTMIP_HS_SYNC_START_DLY */
bf_writel(UTMIP_HS_SYNC_START_DLY, utmip_hs_sync_start_delay,
&usbctlr->utmip_hsrx_cfg1);
/* Proceed the crystal clock disable by >100ns delay. */
udelay(1);
/* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */
bf_writel(UTMIP_PHY_XTAL_CLOCKEN, 1, &usbctlr->utmip_misc_cfg1);
#if defined(CONFIG_TEGRA3)
if (id == PERIPH_ID_USBD)
bf_writel(UTMIP_FORCE_PD_SAMP_A_POWERDOWN, 0,
&clkrst->crc_pll_cfg2);
if (id == PERIPH_ID_USB3)
bf_writel(UTMIP_FORCE_PD_SAMP_C_POWERDOWN, 0,
&clkrst->crc_pll_cfg2);
#endif
/* Finished the per-controller init. */
/* De-assert UTMIP_RESET to bring out of reset. */
bf_clearl(UTMIP_RESET, &usbctlr->susp_ctrl);
/* Wait for the phy clock to become valid in 100 ms */
for (loop_count = 100000; loop_count != 0; loop_count--) {
if (bf_readl(USB_PHY_CLK_VALID, &usbctlr->susp_ctrl))
break;
udelay(1);
}
}