static int phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
u32 op, u16 *data)
{
u32 mgtcr;
struct zynq_gem_regs *regs = priv->iobase;
int err;
err = wait_for_bit_le32(®s->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
true, 20000, false);
if (err)
return err;
/* Construct mgtcr mask for the operation */
mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
(phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
(regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;
/* Write mgtcr and wait for completion */
writel(mgtcr, ®s->phymntnc);
err = wait_for_bit_le32(®s->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
true, 20000, false);
if (err)
return err;
if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
*data = readl(®s->phymntnc);
return 0;
}
int socfpga_bridges_reset(void)
{
int ret;
/* Disable all the bridges (hps2fpga, lwhps2fpga, fpga2hps,
fpga2sdram) */
/* set idle request to all bridges */
writel(ALT_SYSMGR_NOC_H2F_SET_MSK |
ALT_SYSMGR_NOC_LWH2F_SET_MSK |
ALT_SYSMGR_NOC_F2H_SET_MSK |
ALT_SYSMGR_NOC_F2SDR0_SET_MSK |
ALT_SYSMGR_NOC_F2SDR1_SET_MSK |
ALT_SYSMGR_NOC_F2SDR2_SET_MSK,
&sysmgr_regs->noc_idlereq_set);
/* Enable the NOC timeout */
writel(ALT_SYSMGR_NOC_TMO_EN_SET_MSK, &sysmgr_regs->noc_timeout);
/* Poll until all idleack to 1 */
ret = wait_for_bit_le32(&sysmgr_regs->noc_idleack,
ALT_SYSMGR_NOC_H2F_SET_MSK |
ALT_SYSMGR_NOC_LWH2F_SET_MSK |
ALT_SYSMGR_NOC_F2H_SET_MSK |
ALT_SYSMGR_NOC_F2SDR0_SET_MSK |
ALT_SYSMGR_NOC_F2SDR1_SET_MSK |
ALT_SYSMGR_NOC_F2SDR2_SET_MSK,
true, 10000, false);
if (ret)
return ret;
/* Poll until all idlestatus to 1 */
ret = wait_for_bit_le32(&sysmgr_regs->noc_idlestatus,
ALT_SYSMGR_NOC_H2F_SET_MSK |
ALT_SYSMGR_NOC_LWH2F_SET_MSK |
ALT_SYSMGR_NOC_F2H_SET_MSK |
ALT_SYSMGR_NOC_F2SDR0_SET_MSK |
ALT_SYSMGR_NOC_F2SDR1_SET_MSK |
ALT_SYSMGR_NOC_F2SDR2_SET_MSK,
true, 10000, false);
if (ret)
return ret;
/* Put all bridges (except NOR DDR scheduler) into reset state */
setbits_le32(&reset_manager_base->brgmodrst,
(ALT_RSTMGR_BRGMODRST_H2F_SET_MSK |
ALT_RSTMGR_BRGMODRST_LWH2F_SET_MSK |
ALT_RSTMGR_BRGMODRST_F2H_SET_MSK |
ALT_RSTMGR_BRGMODRST_F2SSDRAM0_SET_MSK |
ALT_RSTMGR_BRGMODRST_F2SSDRAM1_SET_MSK |
ALT_RSTMGR_BRGMODRST_F2SSDRAM2_SET_MSK));
/* Disable NOC timeout */
writel(0, &sysmgr_regs->noc_timeout);
return 0;
}
static int ehci_usb_remove(struct udevice *dev)
{
struct msm_ehci_priv *p = dev_get_priv(dev);
struct usb_ehci *ehci = p->ehci;
int ret;
ret = ehci_deregister(dev);
if (ret)
return ret;
/* Stop controller. */
clrbits_le32(&ehci->usbcmd, CMD_RUN);
reset_usb_phy(p);
ret = board_prepare_usb(USB_INIT_DEVICE); /* Board specific hook */
if (ret < 0)
return ret;
/* Reset controller */
setbits_le32(&ehci->usbcmd, CMD_RESET);
/* Wait for reset */
if (wait_for_bit_le32(&ehci->usbcmd, CMD_RESET, false, 30, false)) {
printf("Stuck on USB reset.\n");
return -ETIMEDOUT;
}
return 0;
}
/* Initialize mii(MDIO) interface, discover which PHY is
* attached to the device, and configure it properly.
*/
static int pic32_mii_init(struct pic32eth_dev *priv)
{
struct pic32_ectl_regs *ectl_p = priv->ectl_regs;
struct pic32_emac_regs *emac_p = priv->emac_regs;
/* board phy reset */
board_netphy_reset(priv);
/* disable RX, TX & all transactions */
writel(ETHCON_ON | ETHCON_TXRTS | ETHCON_RXEN, &ectl_p->con1.clr);
/* wait till busy */
wait_for_bit_le32(&ectl_p->stat.raw, ETHSTAT_BUSY, false,
CONFIG_SYS_HZ, false);
/* turn controller ON to access PHY over MII */
writel(ETHCON_ON, &ectl_p->con1.set);
mdelay(10);
/* reset MAC */
writel(EMAC_SOFTRESET, &emac_p->cfg1.set); /* reset assert */
mdelay(10);
writel(EMAC_SOFTRESET, &emac_p->cfg1.clr); /* reset deassert */
/* initialize MDIO/MII */
if (priv->phyif == PHY_INTERFACE_MODE_RMII) {
writel(EMAC_RMII_RESET, &emac_p->supp.set);
mdelay(10);
writel(EMAC_RMII_RESET, &emac_p->supp.clr);
}
return pic32_mdio_init(PIC32_MDIO_NAME, (ulong)&emac_p->mii);
}
static void pic32_eth_stop(struct udevice *dev)
{
struct pic32eth_dev *priv = dev_get_priv(dev);
struct pic32_ectl_regs *ectl_p = priv->ectl_regs;
struct pic32_emac_regs *emac_p = priv->emac_regs;
/* Reset the phy if the controller is enabled */
if (readl(&ectl_p->con1.raw) & ETHCON_ON)
phy_reset(priv->phydev);
/* Shut down the PHY */
phy_shutdown(priv->phydev);
/* Stop rx/tx */
writel(ETHCON_TXRTS | ETHCON_RXEN, &ectl_p->con1.clr);
mdelay(10);
/* reset MAC */
writel(EMAC_SOFTRESET, &emac_p->cfg1.raw);
/* clear reset */
writel(0, &emac_p->cfg1.raw);
mdelay(10);
/* disable controller */
writel(ETHCON_ON, &ectl_p->con1.clr);
mdelay(10);
/* wait until everything is down */
wait_for_bit_le32(&ectl_p->stat.raw, ETHSTAT_BUSY, false,
2 * CONFIG_SYS_HZ, false);
/* clear any existing interrupt event */
writel(0xffffffff, &ectl_p->irq.clr);
}
static int rpc_spi_wait_tend(struct udevice *dev)
{
struct rpc_spi_priv *priv = dev_get_priv(dev->parent);
return wait_for_bit_le32((void *)priv->regs + RPC_CMNSR, RPC_CMNSR_TEND,
true, 1000, false);
}
static void zynqmp_qspi_fill_gen_fifo(struct zynqmp_qspi_priv *priv,
u32 gqspi_fifo_reg)
{
struct zynqmp_qspi_regs *regs = priv->regs;
u32 config_reg, ier;
int ret = 0;
config_reg = readl(®s->confr);
/* Manual start if needed */
if (config_reg & GQSPI_GEN_FIFO_STRT_MOD) {
config_reg |= GQSPI_STRT_GEN_FIFO;
writel(config_reg, ®s->confr);
/* Enable interrupts */
ier = readl(®s->ier);
ier |= GQSPI_IXR_ALL_MASK;
writel(ier, ®s->ier);
}
/* Wait until the fifo is not full to write the new command */
ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_GFNFULL_MASK, 1,
GQSPI_TIMEOUT, 1);
if (ret)
printf("%s Timeout\n", __func__);
writel(gqspi_fifo_reg, ®s->genfifo);
}
/* start phy self calibration logic */
static int ddr2_phy_calib_start(void)
{
struct ddr2_phy_regs *ddr2_phy;
ddr2_phy = ioremap(PIC32_DDR2P_BASE, sizeof(*ddr2_phy));
/* DDR Phy SCL Start */
writel(SCL_START | SCL_EN, &ddr2_phy->scl_start);
/* Wait for SCL for data byte to pass */
return wait_for_bit_le32(&ddr2_phy->scl_start, SCL_LUBPASS,
true, CONFIG_SYS_HZ, false);
}
static int zynqmp_qspi_start_dma(struct zynqmp_qspi_priv *priv,
u32 gen_fifo_cmd, u32 *buf)
{
u32 addr;
u32 size, len;
u32 actuallen = priv->len;
int ret = 0;
struct zynqmp_qspi_dma_regs *dma_regs = priv->dma_regs;
writel((unsigned long)buf, &dma_regs->dmadst);
writel(roundup(priv->len, ARCH_DMA_MINALIGN), &dma_regs->dmasize);
writel(GQSPI_DMA_DST_I_STS_MASK, &dma_regs->dmaier);
addr = (unsigned long)buf;
size = roundup(priv->len, ARCH_DMA_MINALIGN);
flush_dcache_range(addr, addr + size);
while (priv->len) {
len = zynqmp_qspi_calc_exp(priv, &gen_fifo_cmd);
if (!(gen_fifo_cmd & GQSPI_GFIFO_EXP_MASK) &&
(len % ARCH_DMA_MINALIGN)) {
gen_fifo_cmd &= ~GENMASK(7, 0);
gen_fifo_cmd |= roundup(len, ARCH_DMA_MINALIGN);
}
zynqmp_qspi_fill_gen_fifo(priv, gen_fifo_cmd);
debug("GFIFO_CMD_RX:0x%x\n", gen_fifo_cmd);
}
ret = wait_for_bit_le32(&dma_regs->dmaisr, GQSPI_DMA_DST_I_STS_DONE,
1, GQSPI_TIMEOUT, 1);
if (ret) {
printf("DMA Timeout:0x%x\n", readl(&dma_regs->dmaisr));
return -ETIMEDOUT;
}
writel(GQSPI_DMA_DST_I_STS_DONE, &dma_regs->dmaisr);
debug("buf:0x%lx, rxbuf:0x%lx, *buf:0x%x len: 0x%x\n",
(unsigned long)buf, (unsigned long)priv->rx_buf, *buf,
actuallen);
if (buf != priv->rx_buf)
memcpy(priv->rx_buf, buf, actuallen);
return 0;
}
static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
{
u32 addr, size;
struct zynq_gem_priv *priv = dev_get_priv(dev);
struct zynq_gem_regs *regs = priv->iobase;
struct emac_bd *current_bd = &priv->tx_bd[1];
/* Setup Tx BD */
memset(priv->tx_bd, 0, sizeof(struct emac_bd));
priv->tx_bd->addr = (ulong)ptr;
priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
ZYNQ_GEM_TXBUF_LAST_MASK;
/* Dummy descriptor to mark it as the last in descriptor chain */
current_bd->addr = 0x0;
current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
ZYNQ_GEM_TXBUF_LAST_MASK|
ZYNQ_GEM_TXBUF_USED_MASK;
/* setup BD */
writel((ulong)priv->tx_bd, ®s->txqbase);
addr = (ulong) ptr;
addr &= ~(ARCH_DMA_MINALIGN - 1);
size = roundup(len, ARCH_DMA_MINALIGN);
flush_dcache_range(addr, addr + size);
addr = (ulong)priv->rxbuffers;
addr &= ~(ARCH_DMA_MINALIGN - 1);
size = roundup((RX_BUF * PKTSIZE_ALIGN), ARCH_DMA_MINALIGN);
flush_dcache_range(addr, addr + size);
barrier();
/* Start transmit */
setbits_le32(®s->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);
/* Read TX BD status */
if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
printf("TX buffers exhausted in mid frame\n");
return wait_for_bit_le32(®s->txsr, ZYNQ_GEM_TSR_DONE,
true, 20000, true);
}
/* initializes the MAC and PHY, then establishes a link */
static void pic32_ctrl_reset(struct pic32eth_dev *priv)
{
struct pic32_ectl_regs *ectl_p = priv->ectl_regs;
u32 v;
/* disable RX, TX & any other transactions */
writel(ETHCON_ON | ETHCON_TXRTS | ETHCON_RXEN, &ectl_p->con1.clr);
/* wait till busy */
wait_for_bit_le32(&ectl_p->stat.raw, ETHSTAT_BUSY, false,
CONFIG_SYS_HZ, false);
/* decrement received buffcnt to zero. */
while (readl(&ectl_p->stat.raw) & ETHSTAT_BUFCNT)
writel(ETHCON_BUFCDEC, &ectl_p->con1.set);
/* clear any existing interrupt event */
writel(0xffffffff, &ectl_p->irq.clr);
/* clear RX/TX start address */
writel(0xffffffff, &ectl_p->txst.clr);
writel(0xffffffff, &ectl_p->rxst.clr);
/* clear the receive filters */
writel(0x00ff, &ectl_p->rxfc.clr);
/* set the receive filters
* ETH_FILT_CRC_ERR_REJECT
* ETH_FILT_RUNT_REJECT
* ETH_FILT_UCAST_ACCEPT
* ETH_FILT_MCAST_ACCEPT
* ETH_FILT_BCAST_ACCEPT
*/
v = ETHRXFC_BCEN | ETHRXFC_MCEN | ETHRXFC_UCEN |
ETHRXFC_RUNTEN | ETHRXFC_CRCOKEN;
writel(v, &ectl_p->rxfc.set);
/* turn controller ON to access PHY over MII */
writel(ETHCON_ON, &ectl_p->con1.set);
}
void mscc_switch_reset(bool enter)
{
/* Nasty workaround to avoid GPIO19 (DDR!) being reset */
mscc_gpio_set_alternate(19, 2);
debug("applying SwC reset\n");
writel(ICPU_RESET_CORE_RST_PROTECT, BASE_CFG + ICPU_RESET);
writel(PERF_SOFT_RST_SOFT_CHIP_RST, BASE_DEVCPU_GCB + PERF_SOFT_RST);
if (wait_for_bit_le32(BASE_DEVCPU_GCB + PERF_SOFT_RST,
PERF_SOFT_RST_SOFT_CHIP_RST, false, 5000, false))
pr_err("Tiemout while waiting for switch reset\n");
/*
* Reset GPIO19 mode back as regular GPIO, output, high (DDR
* not reset) (Order is important)
*/
setbits_le32(BASE_DEVCPU_GCB + PERF_GPIO_OE, BIT(19));
writel(BIT(19), BASE_DEVCPU_GCB + PERF_GPIO_OUT_SET);
mscc_gpio_set_alternate(19, 0);
}
/* Enable bridges (hps2fpga, lwhps2fpga, fpga2hps, fpga2sdram) per handoff */
int socfpga_reset_deassert_bridges_handoff(void)
{
u32 mask_noc = 0, mask_rstmgr = 0;
int i;
for (i = 0; i < ARRAY_SIZE(bridge_cfg_tbl); i++) {
if (get_bridge_init_val(gd->fdt_blob,
bridge_cfg_tbl[i].compat_id)) {
mask_noc |= bridge_cfg_tbl[i].mask_noc;
mask_rstmgr |= bridge_cfg_tbl[i].mask_rstmgr;
}
}
/* clear idle request to all bridges */
setbits_le32(&sysmgr_regs->noc_idlereq_clr, mask_noc);
/* Release bridges from reset state per handoff value */
clrbits_le32(&reset_manager_base->brgmodrst, mask_rstmgr);
/* Poll until all idleack to 0, timeout at 1000ms */
return wait_for_bit_le32(&sysmgr_regs->noc_idleack, mask_noc,
false, 1000, false);
}
/* wait until hardware is ready for another user access */
static int cpsw_mdio_wait_for_user_access(struct cpsw_mdio *mdio)
{
return wait_for_bit_le32(&mdio->regs->user[0].access,
USERACCESS_GO, false,
CPSW_MDIO_TIMEOUT, false);
}
static int sun4i_spi_xfer(struct udevice *dev, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
struct udevice *bus = dev->parent;
struct sun4i_spi_priv *priv = dev_get_priv(bus);
struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
u32 len = bitlen / 8;
u32 reg;
u8 nbytes;
int ret;
priv->tx_buf = dout;
priv->rx_buf = din;
if (bitlen % 8) {
debug("%s: non byte-aligned SPI transfer.\n", __func__);
return -ENAVAIL;
}
if (flags & SPI_XFER_BEGIN)
sun4i_spi_set_cs(bus, slave_plat->cs, true);
reg = readl(&priv->regs->ctl);
/* Reset FIFOs */
writel(reg | SUN4I_CTL_RF_RST | SUN4I_CTL_TF_RST, &priv->regs->ctl);
while (len) {
/* Setup the transfer now... */
nbytes = min(len, (u32)(SUN4I_FIFO_DEPTH - 1));
/* Setup the counters */
writel(SUN4I_BURST_CNT(nbytes), &priv->regs->bc);
writel(SUN4I_XMIT_CNT(nbytes), &priv->regs->tc);
/* Fill the TX FIFO */
sun4i_spi_fill_fifo(priv, nbytes);
/* Start the transfer */
reg = readl(&priv->regs->ctl);
writel(reg | SUN4I_CTL_XCH, &priv->regs->ctl);
/* Wait transfer to complete */
ret = wait_for_bit_le32(&priv->regs->ctl, SUN4I_CTL_XCH_MASK,
false, SUN4I_SPI_TIMEOUT_US, false);
if (ret) {
printf("ERROR: sun4i_spi: Timeout transferring data\n");
sun4i_spi_set_cs(bus, slave_plat->cs, false);
return ret;
}
/* Drain the RX FIFO */
sun4i_spi_drain_fifo(priv, nbytes);
len -= nbytes;
}
if (flags & SPI_XFER_END)
sun4i_spi_set_cs(bus, slave_plat->cs, false);
return 0;
}
static int zynqmp_qspi_fill_tx_fifo(struct zynqmp_qspi_priv *priv, u32 size)
{
u32 data, config_reg, ier;
int ret = 0;
struct zynqmp_qspi_regs *regs = priv->regs;
u32 *buf = (u32 *)priv->tx_buf;
u32 len = size;
debug("TxFIFO: 0x%x, size: 0x%x\n", readl(®s->isr),
size);
config_reg = readl(®s->confr);
/* Manual start if needed */
if (config_reg & GQSPI_GEN_FIFO_STRT_MOD) {
config_reg |= GQSPI_STRT_GEN_FIFO;
writel(config_reg, ®s->confr);
/* Enable interrupts */
ier = readl(®s->ier);
ier |= GQSPI_IXR_ALL_MASK;
writel(ier, ®s->ier);
}
while (size) {
ret = wait_for_bit_le32(®s->isr, GQSPI_IXR_TXNFULL_MASK, 1,
GQSPI_TIMEOUT, 1);
if (ret) {
printf("%s: Timeout\n", __func__);
return ret;
}
if (size >= 4) {
writel(*buf, ®s->txd0r);
buf++;
size -= 4;
} else {
switch (size) {
case 1:
data = *((u8 *)buf);
buf += 1;
data |= GENMASK(31, 8);
break;
case 2:
data = *((u16 *)buf);
buf += 2;
data |= GENMASK(31, 16);
break;
case 3:
data = *((u16 *)buf);
buf += 2;
data |= (*((u8 *)buf) << 16);
buf += 1;
data |= GENMASK(31, 24);
break;
}
writel(data, ®s->txd0r);
size = 0;
}
}
priv->tx_buf += len;
return 0;
}
struct mii_dev *cpsw_mdio_init(const char *name, u32 mdio_base,
u32 bus_freq, int fck_freq)
{
struct cpsw_mdio *cpsw_mdio;
int ret;
cpsw_mdio = calloc(1, sizeof(*cpsw_mdio));
if (!cpsw_mdio) {
debug("failed to alloc cpsw_mdio\n");
return NULL;
}
cpsw_mdio->bus = mdio_alloc();
if (!cpsw_mdio->bus) {
debug("failed to alloc mii bus\n");
free(cpsw_mdio);
return NULL;
}
cpsw_mdio->regs = (struct cpsw_mdio_regs *)mdio_base;
if (!bus_freq || !fck_freq)
cpsw_mdio->div = CPSW_MDIO_DIV_DEF;
else
cpsw_mdio->div = (fck_freq / bus_freq) - 1;
cpsw_mdio->div &= CONTROL_DIV_MASK;
/* set enable and clock divider */
writel(cpsw_mdio->div | CONTROL_ENABLE | CONTROL_FAULT |
CONTROL_FAULT_ENABLE, &cpsw_mdio->regs->control);
wait_for_bit_le32(&cpsw_mdio->regs->control,
CONTROL_IDLE, false, CPSW_MDIO_TIMEOUT, true);
/*
* wait for scan logic to settle:
* the scan time consists of (a) a large fixed component, and (b) a
* small component that varies with the mii bus frequency. These
* were estimated using measurements at 1.1 and 2.2 MHz on tnetv107x
* silicon. Since the effect of (b) was found to be largely
* negligible, we keep things simple here.
*/
mdelay(1);
cpsw_mdio->bus->read = cpsw_mdio_read;
cpsw_mdio->bus->write = cpsw_mdio_write;
cpsw_mdio->bus->priv = cpsw_mdio;
snprintf(cpsw_mdio->bus->name, sizeof(cpsw_mdio->bus->name), name);
ret = mdio_register(cpsw_mdio->bus);
if (ret < 0) {
debug("failed to register mii bus\n");
goto free_bus;
}
return cpsw_mdio->bus;
free_bus:
mdio_free(cpsw_mdio->bus);
free(cpsw_mdio);
return NULL;
}
static int atmel_spi_xfer(struct udevice *dev, unsigned int bitlen,
const void *dout, void *din, unsigned long flags)
{
struct udevice *bus = dev_get_parent(dev);
struct atmel_spi_platdata *bus_plat = dev_get_platdata(bus);
struct at91_spi *reg_base = bus_plat->regs;
u32 len_tx, len_rx, len;
u32 status;
const u8 *txp = dout;
u8 *rxp = din;
u8 value;
if (bitlen == 0)
goto out;
/*
* The controller can do non-multiple-of-8 bit
* transfers, but this driver currently doesn't support it.
*
* It's also not clear how such transfers are supposed to be
* represented as a stream of bytes...this is a limitation of
* the current SPI interface.
*/
if (bitlen % 8) {
/* Errors always terminate an ongoing transfer */
flags |= SPI_XFER_END;
goto out;
}
len = bitlen / 8;
/*
* The controller can do automatic CS control, but it is
* somewhat quirky, and it doesn't really buy us much anyway
* in the context of U-Boot.
*/
if (flags & SPI_XFER_BEGIN) {
atmel_spi_cs_activate(dev);
/*
* sometimes the RDR is not empty when we get here,
* in theory that should not happen, but it DOES happen.
* Read it here to be on the safe side.
* That also clears the OVRES flag. Required if the
* following loop exits due to OVRES!
*/
readl(®_base->rdr);
}
for (len_tx = 0, len_rx = 0; len_rx < len; ) {
status = readl(®_base->sr);
if (status & ATMEL_SPI_SR_OVRES)
return -1;
if ((len_tx < len) && (status & ATMEL_SPI_SR_TDRE)) {
if (txp)
value = *txp++;
else
value = 0;
writel(value, ®_base->tdr);
len_tx++;
}
if (status & ATMEL_SPI_SR_RDRF) {
value = readl(®_base->rdr);
if (rxp)
*rxp++ = value;
len_rx++;
}
}
out:
if (flags & SPI_XFER_END) {
/*
* Wait until the transfer is completely done before
* we deactivate CS.
*/
wait_for_bit_le32(®_base->sr,
ATMEL_SPI_SR_TXEMPTY, true, 1000, false);
atmel_spi_cs_deactivate(dev);
}
return 0;
}
