/**
* PrepareComposite() sets up the driver for doing a Composite operation
* described in the Render extension protocol spec.
*
* @param op Render operation
* @param pSrcPicture source Picture
* @param pMaskPicture mask picture
* @param pDstPicture destination Picture
* @param pSrc source pixmap
* @param pMask mask pixmap
* @param pDst destination pixmap
*
* This call should set up the driver for doing a series of Composite
* operations, as described in the Render protocol spec, with the given
* pSrcPicture, pMaskPicture, and pDstPicture. The pSrc, pMask, and
* pDst are the pixmaps containing the pixel data, and should be used for
* setting the offset and pitch used for the coordinate spaces for each of
* the Pictures.
*
* Notes on interpreting Picture structures:
* - The Picture structures will always have a valid pDrawable.
* - The Picture structures will never have alphaMap set.
* - The mask Picture (and therefore pMask) may be NULL, in which case the
* operation is simply src OP dst instead of src IN mask OP dst, and
* mask coordinates should be ignored.
* - pMarkPicture may have componentAlpha set, which greatly changes
* the behavior of the Composite operation. componentAlpha has no effect
* when set on pSrcPicture or pDstPicture.
* Note: componentAlpha means to treat each R/G/B channel as an independent
* alpha value for the corresponding channel in the src.
* - The source and mask Pictures may have a transformation set
* (Picture->transform != NULL), which means that the source coordinates
* should be transformed by that transformation, resulting in scaling,
* rotation, etc. The PictureTransformPoint() call can transform
* coordinates for you. Transforms have no effect on Pictures when used
* as a destination.
* - The source and mask pictures may have a filter set. PictFilterNearest
* and PictFilterBilinear are defined in the Render protocol, but others
* may be encountered, and must be handled correctly (usually by
* PrepareComposite failing, and falling back to software). Filters have
* no effect on Pictures when used as a destination.
* - The source and mask Pictures may have repeating set, which must be
* respected. Many chipsets will be unable to support repeating on
* pixmaps that have a width or height that is not a power of two.
*
* If your hardware can't support source pictures (textures) with
* non-power-of-two pitches, you should set #EXA_OFFSCREEN_ALIGN_POT.
*
* Note that many drivers will need to store some of the data in the driver
* private record, for sending to the hardware with each drawing command.
*
* The PrepareComposite() call is not required. However, it is highly
* recommended for performance of antialiased font rendering and performance
* of cairo applications. Failure results in a fallback to software
* rendering.
*/
static Bool
XAPrepareComposite(int op, PicturePtr pSrcPicture, PicturePtr pMaskPicture,
PicturePtr pDstPicture, PixmapPtr pSrc, PixmapPtr pMask, PixmapPtr pDst)
{
MSM_LOCALS(pDst);
return xa_composite_prepare(exa->ctx, &exa->comp) == XA_ERR_NONE;
}
/**
* PrepareComposite() sets up the driver for doing a Composite operation
* described in the Render extension protocol spec.
*
* @param op Render operation
* @param pSrcPicture source Picture
* @param pMaskPicture mask picture
* @param pDstPicture destination Picture
* @param pSrc source pixmap
* @param pMask mask pixmap
* @param pDst destination pixmap
*
* This call should set up the driver for doing a series of Composite
* operations, as described in the Render protocol spec, with the given
* pSrcPicture, pMaskPicture, and pDstPicture. The pSrc, pMask, and
* pDst are the pixmaps containing the pixel data, and should be used for
* setting the offset and pitch used for the coordinate spaces for each of
* the Pictures.
*
* Notes on interpreting Picture structures:
* - The Picture structures will always have a valid pDrawable.
* - The Picture structures will never have alphaMap set.
* - The mask Picture (and therefore pMask) may be NULL, in which case the
* operation is simply src OP dst instead of src IN mask OP dst, and
* mask coordinates should be ignored.
* - pMarkPicture may have componentAlpha set, which greatly changes
* the behavior of the Composite operation. componentAlpha has no effect
* when set on pSrcPicture or pDstPicture.
* Note: componentAlpha means to treat each R/G/B channel as an independent
* alpha value for the corresponding channel in the src.
* - The source and mask Pictures may have a transformation set
* (Picture->transform != NULL), which means that the source coordinates
* should be transformed by that transformation, resulting in scaling,
* rotation, etc. The PictureTransformPoint() call can transform
* coordinates for you. Transforms have no effect on Pictures when used
* as a destination.
* - The source and mask pictures may have a filter set. PictFilterNearest
* and PictFilterBilinear are defined in the Render protocol, but others
* may be encountered, and must be handled correctly (usually by
* PrepareComposite failing, and falling back to software). Filters have
* no effect on Pictures when used as a destination.
* - The source and mask Pictures may have repeating set, which must be
* respected. Many chipsets will be unable to support repeating on
* pixmaps that have a width or height that is not a power of two.
*
* If your hardware can't support source pictures (textures) with
* non-power-of-two pitches, you should set #EXA_OFFSCREEN_ALIGN_POT.
*
* Note that many drivers will need to store some of the data in the driver
* private record, for sending to the hardware with each drawing command.
*
* The PrepareComposite() call is not required. However, it is highly
* recommended for performance of antialiased font rendering and performance
* of cairo applications. Failure results in a fallback to software
* rendering.
*/
static Bool
XAPrepareComposite(int op, PicturePtr pSrcPicture, PicturePtr pMaskPicture,
PicturePtr pDstPicture, PixmapPtr pSrc, PixmapPtr pMask, PixmapPtr pDst)
{
MSM_LOCALS(pDst);
EXA_FAIL_IF(!(pMsm->examask & ACCEL_COMPOSITE));
if (!xa_update_composite(&exa->comp, pSrc, pMask, pDst))
return FALSE;
EXA_FAIL_IF(xa_composite_prepare(exa->ctx, &exa->comp) != XA_ERR_NONE);
return TRUE;
}