VOID
ArchInitialize (
VOID
)
{
// Enable Floating Point
if (FixedPcdGet32 (PcdVFPEnabled)) {
ArmEnableVFP ();
}
}
VOID
ArchInitialize (
VOID
)
{
// Enable Floating Point
if (FixedPcdGet32 (PcdVFPEnabled)) {
ArmEnableVFP ();
}
if (ArmReadCurrentEL () == AARCH64_EL2) {
// Trap General Exceptions. All exceptions that would be routed to EL1 are routed to EL2
ArmWriteHcr (ARM_HCR_TGE);
}
}
VOID
CEntryPoint (
IN UINTN MpId,
IN UINTN SecBootMode
)
{
CHAR8 Buffer[100];
UINTN CharCount;
UINTN JumpAddress;
// Invalidate the data cache. Doesn't have to do the Data cache clean.
ArmInvalidateDataCache ();
// Invalidate Instruction Cache
ArmInvalidateInstructionCache ();
// Invalidate I & D TLBs
ArmInvalidateInstructionAndDataTlb ();
// CPU specific settings
ArmCpuSetup (MpId);
// Enable Floating Point Coprocessor if supported by the platform
if (FixedPcdGet32 (PcdVFPEnabled)) {
ArmEnableVFP ();
}
// Initialize peripherals that must be done at the early stage
// Example: Some L2 controller, interconnect, clock, DMC, etc
ArmPlatformSecInitialize (MpId);
// Primary CPU clears out the SCU tag RAMs, secondaries wait
if (ArmPlatformIsPrimaryCore (MpId) && (SecBootMode == ARM_SEC_COLD_BOOT)) {
if (ArmIsMpCore()) {
// Signal for the initial memory is configured (event: BOOT_MEM_INIT)
ArmCallSEV ();
}
// SEC phase needs to run library constructors by hand. This assumes we are linked against the SerialLib
// In non SEC modules the init call is in autogenerated code.
SerialPortInitialize ();
// Start talking
if (FixedPcdGetBool (PcdTrustzoneSupport)) {
CharCount = AsciiSPrint (Buffer,sizeof (Buffer),"Secure firmware (version %s built at %a on %a)\n\r",
(CHAR16*)PcdGetPtr(PcdFirmwareVersionString), __TIME__, __DATE__);
} else {
CharCount = AsciiSPrint (Buffer,sizeof (Buffer),"Boot firmware (version %s built at %a on %a)\n\r",
(CHAR16*)PcdGetPtr(PcdFirmwareVersionString), __TIME__, __DATE__);
}
SerialPortWrite ((UINT8 *) Buffer, CharCount);
// Initialize the Debug Agent for Source Level Debugging
InitializeDebugAgent (DEBUG_AGENT_INIT_PREMEM_SEC, NULL, NULL);
SaveAndSetDebugTimerInterrupt (TRUE);
// Enable the GIC distributor and CPU Interface
// - no other Interrupts are enabled, doesn't have to worry about the priority.
// - all the cores are in secure state, use secure SGI's
ArmGicEnableDistributor (PcdGet32(PcdGicDistributorBase));
ArmGicEnableInterruptInterface (PcdGet32(PcdGicInterruptInterfaceBase));
} else {
// Enable the GIC CPU Interface
ArmGicEnableInterruptInterface (PcdGet32(PcdGicInterruptInterfaceBase));
}
// Enable Full Access to CoProcessors
ArmWriteCpacr (CPACR_CP_FULL_ACCESS);
// Test if Trustzone is supported on this platform
if (FixedPcdGetBool (PcdTrustzoneSupport)) {
if (ArmIsMpCore ()) {
// Setup SMP in Non Secure world
ArmCpuSetupSmpNonSecure (GET_CORE_ID(MpId));
}
// Either we use the Secure Stacks for Secure Monitor (in this case (Base == 0) && (Size == 0))
// Or we use separate Secure Monitor stacks (but (Base != 0) && (Size != 0))
ASSERT (((PcdGet32(PcdCPUCoresSecMonStackBase) == 0) && (PcdGet32(PcdCPUCoreSecMonStackSize) == 0)) ||
((PcdGet32(PcdCPUCoresSecMonStackBase) != 0) && (PcdGet32(PcdCPUCoreSecMonStackSize) != 0)));
// Enter Monitor Mode
enter_monitor_mode (
(UINTN)TrustedWorldInitialization, MpId, SecBootMode,
(VOID*) (PcdGet32 (PcdCPUCoresSecMonStackBase) +
(PcdGet32 (PcdCPUCoreSecMonStackSize) * (ArmPlatformGetCorePosition (MpId) + 1)))
);
} else {
if (ArmPlatformIsPrimaryCore (MpId)) {
SerialPrint ("Trust Zone Configuration is disabled\n\r");
}
// With Trustzone support the transition from Sec to Normal world is done by return_from_exception().
// If we want to keep this function call we need to ensure the SVC's SPSR point to the same Program
// Status Register as the the current one (CPSR).
copy_cpsr_into_spsr ();
// Call the Platform specific function to execute additional actions if required
JumpAddress = PcdGet32 (PcdFvBaseAddress);
ArmPlatformSecExtraAction (MpId, &JumpAddress);
NonTrustedWorldTransition (MpId, JumpAddress);
}
ASSERT (0); // We must never return from the above function
}
