void rtl8225z2_rf_init(struct net_device *dev)
{
struct r8180_priv *priv = ieee80211_priv(dev);
int i;
short channel = 1;
u16 brsr;
u32 data, addr;
priv->chan = channel;
rtl8225_host_pci_init(dev);
write_nic_dword(dev, RF_TIMING, 0x000a8008);
brsr = read_nic_word(dev, BRSR);
write_nic_word(dev, BRSR, 0xffff);
write_nic_dword(dev, RF_PARA, 0x100044);
rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
write_nic_byte(dev, CONFIG3, 0x44);
rtl8180_set_mode(dev, EPROM_CMD_NORMAL);
rtl8185_rf_pins_enable(dev);
write_rtl8225(dev, 0x0, 0x2bf); mdelay(1);
write_rtl8225(dev, 0x1, 0xee0); mdelay(1);
write_rtl8225(dev, 0x2, 0x44d); mdelay(1);
write_rtl8225(dev, 0x3, 0x441); mdelay(1);
write_rtl8225(dev, 0x4, 0x8c3); mdelay(1);
write_rtl8225(dev, 0x5, 0xc72); mdelay(1);
write_rtl8225(dev, 0x6, 0xe6); mdelay(1);
write_rtl8225(dev, 0x7, rtl8225_chan[channel]); mdelay(1);
write_rtl8225(dev, 0x8, 0x3f); mdelay(1);
write_rtl8225(dev, 0x9, 0x335); mdelay(1);
write_rtl8225(dev, 0xa, 0x9d4); mdelay(1);
write_rtl8225(dev, 0xb, 0x7bb); mdelay(1);
write_rtl8225(dev, 0xc, 0x850); mdelay(1);
write_rtl8225(dev, 0xd, 0xcdf); mdelay(1);
write_rtl8225(dev, 0xe, 0x2b); mdelay(1);
write_rtl8225(dev, 0xf, 0x114);
mdelay(100);
write_rtl8225(dev, 0x0, 0x1b7);
for (i = 0; i < 95; i++) {
write_rtl8225(dev, 0x1, (u8)(i + 1));
write_rtl8225(dev, 0x2, rtl8225z2_rxgain[i]);
}
write_rtl8225(dev, 0x3, 0x80);
write_rtl8225(dev, 0x5, 0x4);
write_rtl8225(dev, 0x0, 0xb7);
write_rtl8225(dev, 0x2, 0xc4d);
/* FIXME!! rtl8187 we have to check if calibrarion
* is successful and eventually cal. again (repeat
* the two write on reg 2)
*/
data = read_rtl8225(dev, 6);
if (!(data & 0x00000080)) {
write_rtl8225(dev, 0x02, 0x0c4d);
force_pci_posting(dev); mdelay(200);
write_rtl8225(dev, 0x02, 0x044d);
force_pci_posting(dev); mdelay(100);
data = read_rtl8225(dev, 6);
if (!(data & 0x00000080))
DMESGW("RF Calibration Failed!!!!\n");
}
mdelay(200);
write_rtl8225(dev, 0x0, 0x2bf);
for (i = 0; i < 128; i++) {
data = rtl8225_agc[i];
addr = i + 0x80; /* enable writing AGC table */
write_phy_ofdm(dev, 0xb, data);
mdelay(1);
write_phy_ofdm(dev, 0xa, addr);
mdelay(1);
}
force_pci_posting(dev);
mdelay(1);
write_phy_ofdm(dev, 0x00, 0x01); mdelay(1);
write_phy_ofdm(dev, 0x01, 0x02); mdelay(1);
write_phy_ofdm(dev, 0x02, 0x62); mdelay(1);
write_phy_ofdm(dev, 0x03, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x04, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x05, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x06, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x07, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x08, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x09, 0xfe); mdelay(1);
write_phy_ofdm(dev, 0x0a, 0x08); mdelay(1);
write_phy_ofdm(dev, 0x0b, 0x80); mdelay(1);
write_phy_ofdm(dev, 0x0c, 0x01); mdelay(1);
write_phy_ofdm(dev, 0x0d, 0x43);
write_phy_ofdm(dev, 0x0e, 0xd3); mdelay(1);
write_phy_ofdm(dev, 0x0f, 0x38); mdelay(1);
write_phy_ofdm(dev, 0x10, 0x84); mdelay(1);
write_phy_ofdm(dev, 0x11, 0x07); mdelay(1);
write_phy_ofdm(dev, 0x12, 0x20); mdelay(1);
write_phy_ofdm(dev, 0x13, 0x20); mdelay(1);
write_phy_ofdm(dev, 0x14, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x15, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x16, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x17, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x18, 0xef); mdelay(1);
write_phy_ofdm(dev, 0x19, 0x19); mdelay(1);
write_phy_ofdm(dev, 0x1a, 0x20); mdelay(1);
write_phy_ofdm(dev, 0x1b, 0x15); mdelay(1);
write_phy_ofdm(dev, 0x1c, 0x04); mdelay(1);
write_phy_ofdm(dev, 0x1d, 0xc5); mdelay(1);
write_phy_ofdm(dev, 0x1e, 0x95); mdelay(1);
write_phy_ofdm(dev, 0x1f, 0x75); mdelay(1);
write_phy_ofdm(dev, 0x20, 0x1f); mdelay(1);
write_phy_ofdm(dev, 0x21, 0x17); mdelay(1);
write_phy_ofdm(dev, 0x22, 0x16); mdelay(1);
write_phy_ofdm(dev, 0x23, 0x80); mdelay(1); /* FIXME maybe not needed */
write_phy_ofdm(dev, 0x24, 0x46); mdelay(1);
write_phy_ofdm(dev, 0x25, 0x00); mdelay(1);
write_phy_ofdm(dev, 0x26, 0x90); mdelay(1);
write_phy_ofdm(dev, 0x27, 0x88); mdelay(1);
rtl8225z2_set_gain(dev, 4);
write_phy_cck(dev, 0x0, 0x98); mdelay(1);
write_phy_cck(dev, 0x3, 0x20); mdelay(1);
write_phy_cck(dev, 0x4, 0x7e); mdelay(1);
write_phy_cck(dev, 0x5, 0x12); mdelay(1);
write_phy_cck(dev, 0x6, 0xfc); mdelay(1);
write_phy_cck(dev, 0x7, 0x78); mdelay(1);
write_phy_cck(dev, 0x8, 0x2e); mdelay(1);
write_phy_cck(dev, 0x10, 0x93); mdelay(1);
write_phy_cck(dev, 0x11, 0x88); mdelay(1);
write_phy_cck(dev, 0x12, 0x47); mdelay(1);
write_phy_cck(dev, 0x13, 0xd0);
write_phy_cck(dev, 0x19, 0x00);
write_phy_cck(dev, 0x1a, 0xa0);
write_phy_cck(dev, 0x1b, 0x08);
write_phy_cck(dev, 0x40, 0x86); /* CCK Carrier Sense Threshold */
write_phy_cck(dev, 0x41, 0x8d); mdelay(1);
write_phy_cck(dev, 0x42, 0x15); mdelay(1);
write_phy_cck(dev, 0x43, 0x18); mdelay(1);
write_phy_cck(dev, 0x44, 0x36); mdelay(1);
write_phy_cck(dev, 0x45, 0x35); mdelay(1);
write_phy_cck(dev, 0x46, 0x2e); mdelay(1);
write_phy_cck(dev, 0x47, 0x25); mdelay(1);
write_phy_cck(dev, 0x48, 0x1c); mdelay(1);
write_phy_cck(dev, 0x49, 0x12); mdelay(1);
write_phy_cck(dev, 0x4a, 0x09); mdelay(1);
write_phy_cck(dev, 0x4b, 0x04); mdelay(1);
write_phy_cck(dev, 0x4c, 0x05); mdelay(1);
write_nic_byte(dev, 0x5b, 0x0d); mdelay(1);
rtl8225z2_SetTXPowerLevel(dev, channel);
/* RX antenna default to A */
write_phy_cck(dev, 0x11, 0x9b); mdelay(1); /* B: 0xDB */
write_phy_ofdm(dev, 0x26, 0x90); mdelay(1); /* B: 0x10 */
rtl8185_tx_antenna(dev, 0x03); /* B: 0x00 */
/* switch to high-speed 3-wire
* last digit. 2 for both cck and ofdm
*/
write_nic_dword(dev, 0x94, 0x15c00002);
rtl8185_rf_pins_enable(dev);
rtl8225_rf_set_chan(dev, priv->chan);
}
void rtl8225z2_rf_init(struct net_device *dev)
{
struct r8180_priv *priv = ieee80211_priv(dev);
int i;
short channel = 1;
u16 brsr;
u32 data,addr;
priv->chan = channel;
rtl8180_set_anaparam(dev, RTL8225_ANAPARAM_ON);
if(priv->card_type == USB)
rtl8225_host_usb_init(dev);
else
rtl8225_host_pci_init(dev);
write_nic_dword(dev, RF_TIMING, 0x000a8008);
brsr = read_nic_word(dev, BRSR);
write_nic_word(dev, BRSR, 0xffff);
write_nic_dword(dev, RF_PARA, 0x100044);
#if 1 //0->1
rtl8180_set_mode(dev, EPROM_CMD_CONFIG);
write_nic_byte(dev, CONFIG3, 0x44);
rtl8180_set_mode(dev, EPROM_CMD_NORMAL);
#endif
rtl8185_rf_pins_enable(dev);
// mdelay(1000);
write_rtl8225(dev, 0x0, 0x2bf); mdelay(1);
write_rtl8225(dev, 0x1, 0xee0); mdelay(1);
write_rtl8225(dev, 0x2, 0x44d); mdelay(1);
write_rtl8225(dev, 0x3, 0x441); mdelay(1);
write_rtl8225(dev, 0x4, 0x8c3);mdelay(1);
write_rtl8225(dev, 0x5, 0xc72);mdelay(1);
// }
write_rtl8225(dev, 0x6, 0xe6); mdelay(1);
write_rtl8225(dev, 0x7, ((priv->card_type == USB)? 0x82a : rtl8225_chan[channel])); mdelay(1);
write_rtl8225(dev, 0x8, 0x3f); mdelay(1);
write_rtl8225(dev, 0x9, 0x335); mdelay(1);
write_rtl8225(dev, 0xa, 0x9d4); mdelay(1);
write_rtl8225(dev, 0xb, 0x7bb); mdelay(1);
write_rtl8225(dev, 0xc, 0x850); mdelay(1);
write_rtl8225(dev, 0xd, 0xcdf); mdelay(1);
write_rtl8225(dev, 0xe, 0x2b); mdelay(1);
write_rtl8225(dev, 0xf, 0x114);
mdelay(100);
//if(priv->card_type != USB) /* maybe not needed even for 8185 */
// write_rtl8225(dev, 0x7, rtl8225_chan[channel]);
write_rtl8225(dev, 0x0, 0x1b7);
for(i=0;i<95;i++){
write_rtl8225(dev, 0x1, (u8)(i+1));
#if 0
if(priv->phy_ver == 1)
/* version A */
write_rtl8225(dev, 0x2, rtl8225a_rxgain[i]);
else
#endif
/* version B & C & D*/
write_rtl8225(dev, 0x2, rtl8225z2_rxgain[i]);
}
write_rtl8225(dev, 0x3, 0x80);
write_rtl8225(dev, 0x5, 0x4);
write_rtl8225(dev, 0x0, 0xb7);
write_rtl8225(dev, 0x2, 0xc4d);
if(priv->card_type == USB){
// force_pci_posting(dev);
mdelay(200);
write_rtl8225(dev, 0x2, 0x44d);
// force_pci_posting(dev);
mdelay(100);
}//End of if(priv->card_type == USB)
/* FIXME!! rtl8187 we have to check if calibrarion
* is successful and eventually cal. again (repeat
* the two write on reg 2)
*/
// Check for calibration status, 2005.11.17,
data = read_rtl8225(dev, 6);
if (!(data&0x00000080))
{
write_rtl8225(dev, 0x02, 0x0c4d);
force_pci_posting(dev); mdelay(200);
write_rtl8225(dev, 0x02, 0x044d);
force_pci_posting(dev); mdelay(100);
data = read_rtl8225(dev, 6);
if (!(data&0x00000080))
{
DMESGW("RF Calibration Failed!!!!\n");
}
}
//force_pci_posting(dev);
mdelay(200); //200 for 8187
// //if(priv->card_type != USB){
// write_rtl8225(dev, 0x2, 0x44d);
// write_rtl8225(dev, 0x7, rtl8225_chan[channel]);
// write_rtl8225(dev, 0x2, 0x47d);
//
// force_pci_posting(dev);
// mdelay(100);
//
// write_rtl8225(dev, 0x2, 0x44d);
// //}
write_rtl8225(dev, 0x0, 0x2bf);
if(priv->card_type != USB)
rtl8185_rf_pins_enable(dev);
//set up ZEBRA AGC table, 2005.11.17,
for(i=0;i<128;i++){
data = rtl8225_agc[i];
addr = i + 0x80; //enable writing AGC table
write_phy_ofdm(dev, 0xb, data);
mdelay(1);
write_phy_ofdm(dev, 0xa, addr);
mdelay(1);
}
#if 0
for(i=0;i<128;i++){
write_phy_ofdm(dev, 0xb, rtl8225_agc[i]);
mdelay(1);
write_phy_ofdm(dev, 0xa, (u8)i+ 0x80);
mdelay(1);
}
#endif
force_pci_posting(dev);
mdelay(1);
write_phy_ofdm(dev, 0x0, 0x1); mdelay(1);
write_phy_ofdm(dev, 0x1, 0x2); mdelay(1);
write_phy_ofdm(dev, 0x2, ((priv->card_type == USB)? 0x42 : 0x62)); mdelay(1);
write_phy_ofdm(dev, 0x3, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x4, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x5, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x6, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x7, 0x0); mdelay(1);
write_phy_ofdm(dev, 0x8, 0x40); mdelay(1);
write_phy_ofdm(dev, 0x9, 0xfe); mdelay(1);
write_phy_ofdm(dev, 0xa, 0x8); mdelay(1);
//write_phy_ofdm(dev, 0x18, 0xef);
// }
//}
write_phy_ofdm(dev, 0xb, 0x80); mdelay(1);
write_phy_ofdm(dev, 0xc, 0x1);mdelay(1);
//if(priv->card_type != USB)
write_phy_ofdm(dev, 0xd, 0x43);
write_phy_ofdm(dev, 0xe, 0xd3);mdelay(1);
#if 0
if(priv->card_8185 == 1){
if(priv->card_8185_Bversion)
write_phy_ofdm(dev, 0xf, 0x20);/*ver B*/
else
write_phy_ofdm(dev, 0xf, 0x28);/*ver C*/
}else{
#endif
write_phy_ofdm(dev, 0xf, 0x38);mdelay(1);
/*ver D & 8187*/
// }
// if(priv->card_8185 == 1 && priv->card_8185_Bversion)
// write_phy_ofdm(dev, 0x10, 0x04);/*ver B*/
// else
write_phy_ofdm(dev, 0x10, 0x84);mdelay(1);
/*ver C & D & 8187*/
write_phy_ofdm(dev, 0x11, 0x07);mdelay(1);
/*agc resp time 700*/
// if(priv->card_8185 == 2){
/* Ver D & 8187*/
write_phy_ofdm(dev, 0x12, 0x20);mdelay(1);
write_phy_ofdm(dev, 0x13, 0x20);mdelay(1);
#if 0
}else{
