static void __init osk_init(void)
{
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
* or similar errors if you use NOR flash (e.g. with JFFS2)
*/
if (EMIFS_CCS(3) != EMIFS_CS3_VAL)
EMIFS_CCS(3) = EMIFS_CS3_VAL;
osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
osk_flash_resource.end += SZ_32M - 1;
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_board_config = osk_config;
omap_board_config_size = ARRAY_SIZE(osk_config);
USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
/* irq for tps65010 chip */
/* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
if (gpio_request(OMAP_MPUIO(1), "tps65010") == 0)
gpio_direction_input(OMAP_MPUIO(1));
omap_serial_init();
omap_register_i2c_bus(1, 400, osk_i2c_board_info,
ARRAY_SIZE(osk_i2c_board_info));
osk_mistral_init();
}
static void __init osk_init_smc91x(void)
{
u32 l;
if ((gpio_request(0, "smc_irq")) < 0) {
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
/* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
l = omap_readl(EMIFS_CCS(1));
l |= 0x3;
omap_writel(l, EMIFS_CCS(1));
}
static void __init osk_init(void)
{
u32 l;
osk_init_smc91x();
osk_init_cf();
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
* or similar errors if you use NOR flash (e.g. with JFFS2)
*/
l = omap_readl(EMIFS_CCS(3));
if (l != EMIFS_CS3_VAL)
omap_writel(EMIFS_CS3_VAL, EMIFS_CCS(3));
osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
osk_flash_resource.end += SZ_32M - 1;
osk5912_smc91x_resources[1].start = gpio_to_irq(0);
osk5912_smc91x_resources[1].end = gpio_to_irq(0);
osk5912_cf_resources[0].start = gpio_to_irq(62);
osk5912_cf_resources[0].end = gpio_to_irq(62);
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
l = omap_readl(USB_TRANSCEIVER_CTRL);
l |= (3 << 1);
omap_writel(l, USB_TRANSCEIVER_CTRL);
omap1_usb_init(&osk_usb_config);
/* irq for tps65010 chip */
/* bootloader effectively does: omap_cfg_reg(U19_1610_MPUIO1); */
if (gpio_request(OMAP_MPUIO(1), "tps65010") == 0)
gpio_direction_input(OMAP_MPUIO(1));
omap_serial_init();
osk_i2c_board_info[0].irq = gpio_to_irq(OMAP_MPUIO(1));
omap_register_i2c_bus(1, 400, osk_i2c_board_info,
ARRAY_SIZE(osk_i2c_board_info));
osk_mistral_init();
#ifdef CONFIG_OMAP_OSK_MISTRAL
omapfb_set_lcd_config(&osk_lcd_config);
#endif
}
static void __init osk_init_smc91x(void)
{
if ((omap_request_gpio(0)) < 0) {
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
/* Check EMIFS wait states to fix errors with SMC_GET_PKT_HDR */
EMIFS_CCS(1) |= 0x3;
}
static void __init osk_init(void)
{
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
* or similar errors if you use NOR flash (e.g. with JFFS2)
*/
if (EMIFS_CCS(3) != EMIFS_CS3_VAL)
EMIFS_CCS(3) = EMIFS_CS3_VAL;
osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
osk_flash_resource.end += SZ_32M - 1;
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_board_config = osk_config;
omap_board_config_size = ARRAY_SIZE(osk_config);
USB_TRANSCEIVER_CTRL_REG |= (3 << 1);
omap_serial_init();
osk_mistral_init();
}
