/*---------------------------------------------------------------------------*/
int
cc2420_init(void)
{
uint16_t reg;
{
int s = splhigh();
cc2420_arch_init(); /* Initalize ports and SPI. */
DISABLE_FIFOP_INT();
FIFOP_INT_INIT();
splx(s);
}
/* Turn on voltage regulator and reset. */
SET_VREG_ACTIVE();
//clock_delay(250); OK
SET_RESET_ACTIVE();
clock_delay(127);
SET_RESET_INACTIVE();
//clock_delay(125); OK
/* Turn on the crystal oscillator. */
strobe(CC2420_SXOSCON);
/* Turn on/off automatic packet acknowledgment and address decoding. */
reg = getreg(CC2420_MDMCTRL0);
reg |= 0x40; /* XXX CCA mode 1 */
#if CC2420_CONF_AUTOACK
reg |= AUTOACK | ADR_DECODE;
#else
reg &= ~(AUTOACK | ADR_DECODE);
#endif /* CC2420_CONF_AUTOACK */
setreg(CC2420_MDMCTRL0, reg);
/* Change default values as recomended in the data sheet, */
/* correlation threshold = 20, RX bandpass filter = 1.3uA. */
setreg(CC2420_MDMCTRL1, CORR_THR(20));
reg = getreg(CC2420_RXCTRL1);
reg |= RXBPF_LOCUR;
setreg(CC2420_RXCTRL1, reg);
/* Set the FIFOP threshold to maximum. */
setreg(CC2420_IOCFG0, FIFOP_THR(127));
/* Turn off "Security enable" (page 32). */
reg = getreg(CC2420_SECCTRL0);
reg &= ~RXFIFO_PROTECTION;
setreg(CC2420_SECCTRL0, reg);
cc2420_set_pan_addr(0xffff, 0x0000, NULL);
cc2420_set_channel(26);
process_start(&cc2420_process, NULL);
return 1;
}
void
cc2420_init(void)
{
u16_t reg;
{
int s = splhigh();
__cc2420_arch_init(); /* Initalize ports and SPI. */
DISABLE_FIFOP_INT();
FIFOP_INT_INIT();
splx(s);
}
/* Turn on voltage regulator and reset. */
SET_VREG_ACTIVE();
//clock_delay(250); OK
SET_RESET_ACTIVE();
clock_delay(127);
SET_RESET_INACTIVE();
//clock_delay(125); OK
/* Turn on the crystal oscillator. */
cc2420_strobe(CC2420_SXOSCON);
/* Turn on automatic packet acknowledgment. */
reg = cc2420_getreg(CC2420_MDMCTRL0);
reg |= AUTOACK;
cc2420_setreg(CC2420_MDMCTRL0, reg);
/* Change default values as recomended in the data sheet, */
/* correlation threshold = 20, RX bandpass filter = 1.3uA. */
cc2420_setreg(CC2420_MDMCTRL1, CORR_THR(20));
reg = cc2420_getreg(CC2420_RXCTRL1);
reg |= RXBPF_LOCUR;
cc2420_setreg(CC2420_RXCTRL1, reg);
/* Set the FIFOP threshold to maximum. */
cc2420_setreg(CC2420_IOCFG0, FIFOP_THR(127));
/* Turn off "Security enable" (page 32). */
reg = cc2420_getreg(CC2420_SECCTRL0);
reg &= ~RXFIFO_PROTECTION;
cc2420_setreg(CC2420_SECCTRL0, reg);
cc2420_set_chan_pan_addr(11, 0xffff, 0x0000, NULL);
}
static void
configure(void)
{
uint16_t reg;
BUSYWAIT_UNTIL(status() & (BV(CC2420_XOSC16M_STABLE)), RTIMER_SECOND / 100);
/* Turn on/off automatic packet acknowledgment and address decoding. */
reg = getreg(CC2420_MDMCTRL0);
#if CC2420_CONF_AUTOACK
reg |= AUTOACK | ADR_DECODE;
#else
reg &= ~(AUTOACK | ADR_DECODE);
#endif /* CC2420_CONF_AUTOACK */
setreg(CC2420_MDMCTRL0, reg);
/* Set transmission turnaround time to the lower setting (8 symbols
= 0.128 ms) instead of the default (12 symbols = 0.192 ms). */
/* reg = getreg(CC2420_TXCTRL);
reg &= ~(1 << 13);
setreg(CC2420_TXCTRL, reg);*/
/* Change default values as recomended in the data sheet, */
/* correlation threshold = 20, RX bandpass filter = 1.3uA. */
setreg(CC2420_MDMCTRL1, CORR_THR(20));
reg = getreg(CC2420_RXCTRL1);
reg |= RXBPF_LOCUR;
setreg(CC2420_RXCTRL1, reg);
/* Set the FIFOP threshold to maximum. */
setreg(CC2420_IOCFG0, FIFOP_THR(127));
/* Turn off "Security enable" (page 32). */
reg = getreg(CC2420_SECCTRL0);
reg &= ~RXFIFO_PROTECTION;
setreg(CC2420_SECCTRL0, reg);
cc2420_set_pan_addr(pan, addr, NULL);
cc2420_set_channel(channel);
flushrx();
}
/*---------------------------------------------------------------------------*/
int
cc2520_init(void)
{
{
int s = splhigh();
cc2520_arch_init(); /* Initalize ports and SPI. */
CC2520_DISABLE_FIFOP_INT();
CC2520_FIFOP_INT_INIT();
splx(s);
}
SET_VREG_INACTIVE();
clock_delay(250);
/* Turn on voltage regulator and reset. */
SET_VREG_ACTIVE();
clock_delay(250);
SET_RESET_ACTIVE();
clock_delay(127);
SET_RESET_INACTIVE();
clock_delay(125);
/* Turn on the crystal oscillator. */
strobe(CC2520_INS_SXOSCON);
clock_delay(125);
BUSYWAIT_UNTIL(status() & (BV(CC2520_XOSC16M_STABLE)), RTIMER_SECOND / 100);
/* Change default values as recommended in the data sheet, */
/* correlation threshold = 20, RX bandpass filter = 1.3uA.*/
setreg(CC2520_TXCTRL, 0x94);
setreg(CC2520_TXPOWER, 0x13); // Output power 1 dBm
/*
valeurs de TXPOWER
0x03 -> -18 dBm
0x2C -> -7 dBm
0x88 -> -4 dBm
0x81 -> -2 dBm
0x32 -> 0 dBm
0x13 -> 1 dBm
0x32 -> 0 dBm
0x13 -> 1 dBm
0xAB -> 2 dBm
0xF2 -> 3 dBm
0xF7 -> 5 dBm
*/
setreg(CC2520_CCACTRL0, 0xF8); // CCA treshold -80dBm
// Recommended RX settings
setreg(CC2520_MDMCTRL0, 0x84); // Controls modem
setreg(CC2520_MDMCTRL1, 0x14); // Controls modem
setreg(CC2520_RXCTRL, 0x3F); // Adjust currents in RX related analog modules
setreg(CC2520_FSCTRL, 0x5A); // Adjust currents in synthesizer.
setreg(CC2520_FSCAL1, 0x2B); // Adjust currents in VCO
setreg(CC2520_AGCCTRL1, 0x11); // Adjust target value for AGC control loop
setreg(CC2520_AGCCTRL2, 0xEB);
// Disable external clock
setreg(CC2520_EXTCLOCK, 0x00);
// Tune ADC performance
setreg(CC2520_ADCTEST0, 0x10);
setreg(CC2520_ADCTEST1, 0x0E);
setreg(CC2520_ADCTEST2, 0x03);
/* Set auto CRC on frame. */
#if CC2520_CONF_AUTOACK
setreg(CC2520_FRMCTRL0, AUTOCRC | AUTOACK);
setreg(CC2520_FRMFILT0, FRAME_MAX_VERSION|FRAME_FILTER_ENABLE);
#else
/* setreg(CC2520_FRMCTRL0, 0x60); */
setreg(CC2520_FRMCTRL0, AUTOCRC);
/* Disable filter on @ (remove if you want to address specific wismote) */
setreg(CC2520_FRMFILT0, 0x00);
#endif /* CC2520_CONF_AUTOACK */
/* SET_RXENMASK_ON_TX */
setreg(CC2520_FRMCTRL1, 1);
/* Set FIFOP threshold to maximum .*/
setreg(CC2520_FIFOPCTRL, FIFOP_THR(0x7F));
cc2520_set_pan_addr(0xffff, 0x0000, NULL);
cc2520_set_channel(26);
flushrx();
process_start(&cc2520_process, NULL);
return 1;
}
/*---------------------------------------------------------------------------*/
int
cc2420_init(void)
{
uint16_t reg;
{
int s = splhigh();
cc2420_arch_init(); /* Initalize ports and SPI. */
CC2420_DISABLE_FIFOP_INT();
CC2420_FIFOP_INT_INIT();
splx(s);
}
/* Turn on voltage regulator and reset. */
SET_VREG_ACTIVE();
clock_delay(250);
SET_RESET_ACTIVE();
clock_delay(127);
SET_RESET_INACTIVE();
clock_delay(125);
/* Turn on the crystal oscillator. */
strobe(CC2420_SXOSCON);
/* Turn on/off automatic packet acknowledgment and address decoding. */
reg = getreg(CC2420_MDMCTRL0);
#if CC2420_CONF_AUTOACK
reg |= AUTOACK | ADR_DECODE;
#else
reg &= ~(AUTOACK | ADR_DECODE);
#endif /* CC2420_CONF_AUTOACK */
setreg(CC2420_MDMCTRL0, reg);
/* Set transmission turnaround time to the lower setting (8 symbols
= 0.128 ms) instead of the default (12 symbols = 0.192 ms). */
/* reg = getreg(CC2420_TXCTRL);
reg &= ~(1 << 13);
setreg(CC2420_TXCTRL, reg);*/
/* Change default values as recomended in the data sheet, */
/* correlation threshold = 20, RX bandpass filter = 1.3uA. */
setreg(CC2420_MDMCTRL1, CORR_THR(20));
reg = getreg(CC2420_RXCTRL1);
reg |= RXBPF_LOCUR;
setreg(CC2420_RXCTRL1, reg);
/* Set the FIFOP threshold to maximum. */
setreg(CC2420_IOCFG0, FIFOP_THR(127));
/* Turn off "Security enable" (page 32). */
reg = getreg(CC2420_SECCTRL0);
reg &= ~RXFIFO_PROTECTION;
setreg(CC2420_SECCTRL0, reg);
cc2420_set_pan_addr(0xffff, 0x0000, NULL);
cc2420_set_channel(CC2420_CONF_CHANNEL);
cc2420_set_cca_threshold(CC2420_CONF_CCA_THRESH);
flushrx();
process_start(&cc2420_process, NULL);
return 1;
}
