/**
* @brief Writes a value in a register of the device through BUS in using DMA mode.
* @param Addr: Device address on BUS Bus.
* @param Reg: The target register address to write
* @param pBuffer: The target register value to be written
* @param Length: buffer size to be written
* @retval HAL status
*/
static HAL_StatusTypeDef I2Cx_WriteBufferDMA(uint8_t Addr, uint16_t Reg, uint8_t *pBuffer, uint16_t Length)
{
HAL_StatusTypeDef status = HAL_OK;
status = HAL_I2C_Mem_Write_DMA(&I2cHandle, Addr, Reg, I2C_MEMADD_SIZE_16BIT, pBuffer, Length);
/* Check the communication status */
if(status != HAL_OK)
{
/* Re-Initialize the BUS */
I2Cx_Error();
}
return status;
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Set NVIC Group Priority to 4
- Low Level Initialization: global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to 180 MHz */
SystemClock_Config();
/* Configure LED1, LED2 and LED3 */
BSP_LED_Init(LED1);
BSP_LED_Init(LED2);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral #######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.ClockSpeed = 400000;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
I2cHandle.Init.OwnAddress1 = 0x00;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.OwnAddress2 = 0x00;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
if (HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* The board sends the message to EEPROM then reads it back */
/*##-2- Start writing process ##############################################*/
/* Initialize Remaining Bytes Value to TX Buffer Size */
Remaining_Bytes = TXBUFFERSIZE;
/* Initialize Memory address to 0 since EEPROM write will start from address 0 */
Memory_Address = 0;
/* Since page size is 4 bytes, the write procedure will be done in a loop */
while (Remaining_Bytes > 0)
{
/* Write EEPROM_PAGESIZE */
if(HAL_I2C_Mem_Write_DMA(&I2cHandle , (uint16_t)EEPROM_ADDRESS, Memory_Address, I2C_MEMADD_SIZE_16BIT, (uint8_t*)(aTxBuffer + Memory_Address), EEPROM_PAGESIZE)!= HAL_OK)
{
/* Writing process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
/* Before starting a new communication transfer, you need to check the current
state of the peripheral; if it’s busy you need to wait for the end of current
transfer before starting a new one.
For simplicity reasons, this example is just waiting till the end of the
transfer, but application may perform other tasks while transfer operation
is ongoing. */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check if the EEPROM is ready for a new operation */
while (HAL_I2C_IsDeviceReady(&I2cHandle, EEPROM_ADDRESS, EEPROM_MAX_TRIALS, I2Cx_TIMEOUT_MAX) == HAL_TIMEOUT);
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Update Remaining bytes and Memory Address values */
Remaining_Bytes -= EEPROM_PAGESIZE;
Memory_Address += EEPROM_PAGESIZE;
}
/*##-3- Start reading process ##############################################*/
if (HAL_I2C_Mem_Read_DMA(&I2cHandle, (uint16_t)EEPROM_ADDRESS, 0, I2C_MEMADD_SIZE_16BIT, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Reading process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Compare the sent and received buffers ##############################*/
if (Buffercmp((uint8_t *)aTxBuffer, (uint8_t *)aRxBuffer, RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/* STM32F0xx HAL library initialization:
- Configure the Flash prefetch
- Systick timer is configured by default as source of time base, but user
can eventually implement his proper time base source (a general purpose
timer for example or other time source), keeping in mind that Time base
duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
handled in milliseconds basis.
- Low Level Initialization
*/
HAL_Init();
/* Configure the system clock to 48 MHz */
SystemClock_Config();
/* Configure LED5, LED4 and LED3 */
BSP_LED_Init(LED5);
BSP_LED_Init(LED4);
BSP_LED_Init(LED3);
/*##-1- Configure the I2C peripheral #######################################*/
I2cHandle.Instance = I2Cx;
I2cHandle.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
I2cHandle.Init.Timing = I2Cx_TIMING;
I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
I2cHandle.Init.OwnAddress1 = 0;
I2cHandle.Init.OwnAddress2 = 0;
I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
I2cHandle.Init.NoStretchMode = I2C_NOSTRETCH_DISABLED;
if (HAL_I2C_Init(&I2cHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/* The board sends the message to EEPROM then reads it back */
/*##-2- Start writing process ##############################################*/
/* Initialize Remaining Bytes Value to TX Buffer Size */
Remaining_Bytes = TXBUFFERSIZE;
/* Initialize Memory address to 0 since EEPROM write will start from address 0 */
Memory_Address = 0;
/* Since page size is 4 bytes, the write procedure will be done in a loop */
while (Remaining_Bytes > 0)
{
/* Write 4 bytes */
if (HAL_I2C_Mem_Write_DMA(&I2cHandle, (uint16_t)I2C_ADDRESS, Memory_Address, I2C_MEMADD_SIZE_16BIT, (uint8_t *)(aTxBuffer + Memory_Address), 4) != HAL_OK)
{
/* Writing process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Check if the EEPROM is ready for a new operation */
while (HAL_I2C_IsDeviceReady(&I2cHandle, I2C_ADDRESS, 20, 300) == HAL_TIMEOUT);
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/* Update Remaining bytes and Memory Address values */
Remaining_Bytes -= 4;
Memory_Address += 4;
}
/*##-3- Start reading process ##############################################*/
if (HAL_I2C_Mem_Read_DMA(&I2cHandle, (uint16_t)I2C_ADDRESS, 0, I2C_MEMADD_SIZE_16BIT, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
{
/* Reading process Error */
Error_Handler();
}
/* Wait for the end of the transfer */
while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
{
}
/*##-4- Compare the sent and received buffers ##############################*/
if (Buffercmp((uint8_t *)aTxBuffer, (uint8_t *)aRxBuffer, RXBUFFERSIZE))
{
/* Processing Error */
Error_Handler();
}
/* Infinite loop */
while (1)
{
}
}