예제 #1
0
////////////////////////////////////////////////////////////////////////////////
//! \brief  Prepares the power block for the application.
//!
//! \return SUCCESS(0) Power block ready.
////////////////////////////////////////////////////////////////////////////////
//int PowerPrep( void )
int _start( void )
{
	int iRtn = SUCCESS;
#ifndef mx28
	HW_DIGCTL_CTRL_SET(BM_DIGCTL_CTRL_USE_SERIAL_JTAG);
#else

#define SSP0_PIN_DRIVE_12mA 0x2
// For EMI 200MHz,must enable SSP0 pin drive to 12mA,or the SD boot will fail.
        HW_PINCTRL_DRIVE8_CLR(
		BM_PINCTRL_DRIVE8_BANK2_PIN07_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN06_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN05_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN04_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN03_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN02_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN01_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN00_MA);

	HW_PINCTRL_DRIVE9_CLR(
		BM_PINCTRL_DRIVE9_BANK2_PIN10_MA |
		BM_PINCTRL_DRIVE9_BANK2_PIN09_MA |
		BM_PINCTRL_DRIVE9_BANK2_PIN08_MA);

	HW_PINCTRL_DRIVE8_SET(
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN07_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN06_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN05_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN04_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN03_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN02_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN01_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN00_MA));

	HW_PINCTRL_DRIVE9_SET(
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN10_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN09_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN08_MA));

#endif

	PowerPrep_CPUClock2XTAL();
	PowerPrep_ClearAutoRestart();

	hw_power_SetPowerClkGate( false );

	printf("\r\nPowerPrep start initialize power...\r\n");
	HW_POWER_VDDDCTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;
	HW_POWER_VDDACTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;
	HW_POWER_VDDIOCTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;

	// Ready the power block for 5V detection.
	PowerPrep_Setup5vDetect();
	PowerPrep_SetupBattDetect();

	// Ensure the power source that turned on the device is sufficient to
	// power the device.
	PowerPrep_ConfigurePowerSource();

	PowerPrep_EnableOutputRailProtection();
	/* 3.3V is necessary to achieve best power supply capability
	* and best EMI I/O performance.
	*/
	ddi_power_SetVddio(3300, 3150);

	HW_POWER_CTRL_CLR(BM_POWER_CTRL_VDDD_BO_IRQ |
	BM_POWER_CTRL_VDDA_BO_IRQ |
	BM_POWER_CTRL_VDDIO_BO_IRQ |
	BM_POWER_CTRL_VDD5V_DROOP_IRQ |
	BM_POWER_CTRL_VBUSVALID_IRQ |
	BM_POWER_CTRL_BATT_BO_IRQ |
	BM_POWER_CTRL_DCDC4P2_BO_IRQ
	);
	/* If Battery not ready,setup the auto power down if we lost 5V.*/
	if (!bBatteryReady)
	{
		HW_POWER_5VCTRL_SET(BM_POWER_5VCTRL_PWDN_5VBRNOUT);

#if defined(NO_DCDC_BATT_SOURCE) && defined(mx28)
	/* On i.MX28, a new bit has been added to allow automatic hardware
	 * shutdown if VDD4P2 browns out.  If we permanently only have a VDD5V
	 * source, we want to enable this bit.  For devices with dead batteries,
	 * we could also temporarily set this bit until the kernel battery
	 * charger sufficiently charges the battery but we won't do this for
	 * now as the latest release kernel versions aren't aware of  it
	 * and thus don't handle the proper setting/clearing of this bit.
	 */
		HW_POWER_REFCTRL_SET(1<<7);
#endif

	}


	return iRtn;
}
예제 #2
0
파일: power_prep.c 프로젝트: yangsong2512/C
////////////////////////////////////////////////////////////////////////////////
//! \brief  Prepares the power block for the application.
//!
//! \return SUCCESS(0) Power block ready.
////////////////////////////////////////////////////////////////////////////////
//int PowerPrep( void )
int _start( void )
{
	int iRtn = SUCCESS;
	auart_init();
#ifndef mx28
	HW_DIGCTL_CTRL_SET(BM_DIGCTL_CTRL_USE_SERIAL_JTAG);
#else

#define SSP0_PIN_DRIVE_12mA 0x2
// For EMI 200MHz,must enable SSP0 pin drive to 12mA,or the SD boot will fail.
        HW_PINCTRL_DRIVE8_CLR(
		BM_PINCTRL_DRIVE8_BANK2_PIN07_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN06_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN05_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN04_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN03_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN02_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN01_MA |
		BM_PINCTRL_DRIVE8_BANK2_PIN00_MA);

	HW_PINCTRL_DRIVE9_CLR(
		BM_PINCTRL_DRIVE9_BANK2_PIN10_MA |
		BM_PINCTRL_DRIVE9_BANK2_PIN09_MA |
		BM_PINCTRL_DRIVE9_BANK2_PIN08_MA);

	HW_PINCTRL_DRIVE8_SET(
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN07_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN06_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN05_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN04_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN03_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN02_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN01_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE8_BANK2_PIN00_MA));

	HW_PINCTRL_DRIVE9_SET(
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN10_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN09_MA) |
		(SSP0_PIN_DRIVE_12mA << BP_PINCTRL_DRIVE9_BANK2_PIN08_MA));

#endif

	PowerPrep_CPUClock2XTAL();
	PowerPrep_ClearAutoRestart();

	hw_power_SetPowerClkGate( false );

	printf("\r\nPowerPrep start initialize power...\r\n");
	HW_POWER_VDDDCTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;
	HW_POWER_VDDACTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;
	HW_POWER_VDDIOCTRL.B.LINREG_OFFSET = HW_POWER_LINREG_OFFSET_STEP_BELOW;

	// Ready the power block for 5V detection.
	PowerPrep_Setup5vDetect();
	PowerPrep_SetupBattDetect();

	// Ensure the power source that turned on the device is sufficient to
	// power the device.
	PowerPrep_ConfigurePowerSource();

	PowerPrep_EnableOutputRailProtection();
	/* 3.3V is necessary to achieve best power supply capability
	* and best EMI I/O performance.
	*/
	ddi_power_SetVddio(3300, 3150);

#ifdef mx28
	ddi_power_SetVddd(1350, 1200);
#endif

	HW_POWER_CTRL_CLR(BM_POWER_CTRL_VDDD_BO_IRQ |
	BM_POWER_CTRL_VDDA_BO_IRQ |
	BM_POWER_CTRL_VDDIO_BO_IRQ |
	BM_POWER_CTRL_VDD5V_DROOP_IRQ |
	BM_POWER_CTRL_VBUSVALID_IRQ |
	BM_POWER_CTRL_BATT_BO_IRQ |
	BM_POWER_CTRL_DCDC4P2_BO_IRQ
	);
	/* If Battery not ready,setup the auto power down if we lost 5V.*/
	if (!bBatteryReady)
		HW_POWER_5VCTRL_SET(BM_POWER_5VCTRL_PWDN_5VBRNOUT);
	return iRtn;
}