phys_size_t initdram (int board_type)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size_b0;
memctl->memc_or2 = CONFIG_SYS_OR2;
memctl->memc_br2 = CONFIG_SYS_BR2;
udelay(100);
upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
memctl->memc_mptpr = MPTPR_PTP_DIV16;
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_1X;
/*Do the initialization of the SDRAM*/
/*Start with the precharge cycle*/
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(1) | MCR_MAD(0x5));
/*Then we need two refresh cycles*/
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_2X;
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(2) | MCR_MAD(0x30));
/*Mode register programming*/
memctl->memc_mar = 0x00000088; /*CAS Latency = 2 and burst length = 4*/
memctl->memc_mcr = (MCR_OP_RUN | MCR_UPM_A | MCR_MB_CS2 | \
MCR_MLCF(1) | MCR_MAD(0x1C));
/* That should do it, just enable the periodic refresh in burst of 4*/
memctl->memc_mamr = CONFIG_SYS_MAMR_48_SDR | MAMR_TLFA_4X;
memctl->memc_mamr |= (MAMR_PTAE | MAMR_GPL_A4DIS);
size_b0 = 16*1024*1024;
/*
* No bank 1 or 3
* invalidate bank
*/
memctl->memc_br1 = 0;
memctl->memc_br3 = 0;
upmconfig(UPMB, (uint *)dsp_disp_table, sizeof(dsp_disp_table)/sizeof(uint));
memctl->memc_mbmr = MBMR_GPL_B4DIS;
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
return (size_b0);
}
phys_size_t initdram(int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMA, (uint *) sdram_table, sizeof(sdram_table) / sizeof(uint));
/*
* Preliminary prescaler for refresh
*/
memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
memctl->memc_mar = MAR_SDRAM_INIT; /* 32-bit address to be output on the address bus if AMX = 0b11 */
/*
* Map controller bank 3 to the SDRAM bank at preliminary address.
*/
memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL & ~MAMR_PTAE; /* no refresh yet */
udelay(200);
/* perform SDRAM initialisation sequence */
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(1) | MCR_MAD(0x3C); /* precharge all */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(0) | MCR_MAD(0x30); /* refresh 16 times(0) */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UM_UPMA | MCR_MB_CS3 | MCR_MCLF(1) | MCR_MAD(0x3E); /* exception program (write mar) */
udelay(1);
memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
udelay(1000);
memctl->memc_mamr = CONFIG_SYS_MAMR_9COL;
size = SDRAM_MAX_SIZE;
udelay(10000);
return (size);
}
phys_size_t initdram(int board_type)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
long int size;
upmconfig(UPMB, (uint *) sdram_table, sizeof(sdram_table) / sizeof(sdram_table[0]));
/*
* Preliminary prescaler for refresh
*/
memctl->memc_mptpr = MPTPR_PTP_DIV8;
memctl->memc_mar = MAR_SDRAM_INIT; /* 32-bit address to be output on the address bus if AMX = 0b11 */
/*
* Map controller bank 3 to the SDRAM bank at preliminary address.
*/
memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
memctl->memc_mbmr = CONFIG_SYS_MAMR & ~MAMR_PTAE; /* no refresh yet */
udelay(200);
/* perform SDRAM initialisation sequence */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(1) | MCR_MAD(0x3C); /* precharge all */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(2) | MCR_MAD(0x30); /* refresh 2 times(0) */
udelay(1);
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS3 | MCR_MLCF(1) | MCR_MAD(0x3E); /* exception program (write mar)*/
udelay(1);
memctl->memc_mbmr |= MAMR_PTAE; /* enable refresh */
udelay(10000);
{
u32 d1, d2;
d1 = 0xAA55AA55;
*(volatile u32 *)0 = d1;
d2 = *(volatile u32 *)0;
if (d1 != d2) {
printf("DRAM fails: wrote 0x%08x read 0x%08x\n", d1, d2);
hang();
}
d1 = 0x55AA55AA;
*(volatile u32 *)0 = d1;
d2 = *(volatile u32 *)0;
if (d1 != d2) {
printf("DRAM fails: wrote 0x%08x read 0x%08x\n", d1, d2);
hang();
}
}
size = get_ram_size((long *)0, SDRAM_MAX_SIZE);
if (size == 0) {
printf("SIZE is zero: LOOP on 0\n");
for (;;) {
*(volatile u32 *)0 = 0;
(void)*(volatile u32 *)0;
}
}
return size;
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
/* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CONFIG_SYS_SPC1920_PLD_BASE; */
long int size_b0;
long int size8, size9;
int i;
/*
* Configure UPMB for SDRAM
*/
upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
udelay(100);
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
/* burst length=4, burst type=sequential, CAS latency=2 */
memctl->memc_mar = CONFIG_SYS_MAR;
/*
* Map controller bank 1 to the SDRAM bank at preliminary address.
*/
memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
/* initialize memory address register */
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
/* mode initialization (offset 5) */
udelay (200); /* 0x80006105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006130 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
udelay (1); /* 0x80006106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
udelay (200);
/* Need at least 10 DRAM accesses to stabilize */
for (i = 0; i < 10; ++i) {
volatile unsigned long *addr =
(volatile unsigned long *) CONFIG_SYS_SDRAM_BASE;
unsigned long val;
val = *(addr + i);
*(addr + i) = val;
}
/*
* Check Bank 0 Memory Size for re-configuration
*
* try 8 column mode
*/
size8 = dram_size (CONFIG_SYS_MBMR_8COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
udelay (1000);
/*
* try 9 column mode
*/
size9 = dram_size (CONFIG_SYS_MBMR_9COL, (long *)CONFIG_SYS_SDRAM_BASE, SDRAM_MAX_SIZE);
if (size8 < size9) { /* leave configuration at 9 columns */
size_b0 = size9;
memctl->memc_mbmr = CONFIG_SYS_MBMR_9COL | MBMR_PTBE;
udelay (500);
} else { /* back to 8 columns */
size_b0 = size8;
memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
udelay (500);
}
/*
* Final mapping:
*/
memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
udelay (1000);
/* initalize the DSP Host Port Interface */
hpi_init();
/* FRAM Setup */
memctl->memc_or4 = CONFIG_SYS_OR4;
memctl->memc_br4 = CONFIG_SYS_BR4;
udelay(1000);
return (size_b0);
}
phys_size_t initdram (int board_type)
{
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8xx_t *memctl = &immr->im_memctl;
long int size_b0, reg;
int i;
/*
* Configure UPMA for SDRAM
*/
upmconfig (UPMA, (uint *) sdram_table,
sizeof (sdram_table) / sizeof (uint));
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
/* burst length=4, burst type=sequential, CAS latency=2 */
memctl->memc_mar = 0x00000088;
/*
* Map controller bank 2 to the SDRAM bank at preliminary address.
*/
#if PCU_E_WITH_SWAPPED_CS /* XXX */
memctl->memc_or5 = CONFIG_SYS_OR5_PRELIM;
memctl->memc_br5 = CONFIG_SYS_BR5_PRELIM;
#else /* XXX */
memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
#endif /* XXX */
/* initialize memory address register */
memctl->memc_mamr = CONFIG_SYS_MAMR; /* refresh not enabled yet */
/* mode initialization (offset 5) */
#if PCU_E_WITH_SWAPPED_CS /* XXX */
udelay (200); /* 0x8000A105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS5 | MCR_MLCF (1) | MCR_MAD (0x05);
#else /* XXX */
udelay (200); /* 0x80004105 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS2 | MCR_MLCF (1) | MCR_MAD (0x05);
#endif /* XXX */
/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
#if PCU_E_WITH_SWAPPED_CS /* XXX */
udelay (1); /* 0x8000A830 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS5 | MCR_MLCF (8) | MCR_MAD (0x30);
#else /* XXX */
udelay (1); /* 0x80004830 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS2 | MCR_MLCF (8) | MCR_MAD (0x30);
#endif /* XXX */
#if PCU_E_WITH_SWAPPED_CS /* XXX */
udelay (1); /* 0x8000A106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS5 | MCR_MLCF (1) | MCR_MAD (0x06);
#else /* XXX */
udelay (1); /* 0x80004106 */
memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS2 | MCR_MLCF (1) | MCR_MAD (0x06);
#endif /* XXX */
reg = memctl->memc_mamr;
reg &= ~MAMR_TLFA_MSK; /* switch timer loop ... */
reg |= MAMR_TLFA_4X; /* ... to 4x */
reg |= MAMR_PTAE; /* enable refresh */
memctl->memc_mamr = reg;
udelay (200);
/* Need at least 10 DRAM accesses to stabilize */
for (i = 0; i < 10; ++i) {
#if PCU_E_WITH_SWAPPED_CS /* XXX */
volatile unsigned long *addr =
(volatile unsigned long *) SDRAM_BASE5_PRELIM;
#else /* XXX */
volatile unsigned long *addr =
(volatile unsigned long *) SDRAM_BASE2_PRELIM;
#endif /* XXX */
unsigned long val;
val = *(addr + i);
*(addr + i) = val;
}
/*
* Check Bank 0 Memory Size for re-configuration
*/
#if PCU_E_WITH_SWAPPED_CS /* XXX */
size_b0 = dram_size (CONFIG_SYS_MAMR, (long *) SDRAM_BASE5_PRELIM, SDRAM_MAX_SIZE);
#else /* XXX */
size_b0 = dram_size (CONFIG_SYS_MAMR, (long *) SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
#endif /* XXX */
memctl->memc_mamr = CONFIG_SYS_MAMR | MAMR_PTAE;
/*
* Final mapping:
*/
#if PCU_E_WITH_SWAPPED_CS /* XXX */
memctl->memc_or5 = ((-size_b0) & 0xFFFF0000) | SDRAM_TIMING;
memctl->memc_br5 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
#else /* XXX */
memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | SDRAM_TIMING;
memctl->memc_br2 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
#endif /* XXX */
udelay (1000);
/*
* Configure UPMB for PUMA
*/
upmconfig (UPMB, (uint *) puma_table,
sizeof (puma_table) / sizeof (uint));
return (size_b0);
}