void main(void)
{
// setup microcontroller
PLLCON = 0x00;
P0 = 0x00;
P1 &= ~(1<<6);
P1 &= ~(1<<7);
// Set up the scheduler
SCH_Init_T2();
// init tasks
init_statemachine();
// - timings are in ticks (~1 ms tick interval)
SCH_Add_Task(statemachine, 0, 10);
SCH_Add_Task(switchStateMachine, 5, 20);
// Start the scheduler
SCH_Start();
while(1) {
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCU_B_SLAVE_Init_T1(9600);
// Set up the flash LED task (demo purposes)
LED_Flash_Init();
// Prepare for the traffic light task
TRAFFIC_LIGHTS_Init();
// Add a 'flash LED' task (on for 1000 ms, off for 1000 ms)
SCH_Add_Task(LED_Flash_Update, 0, 200);
// Add a 'traffic lights' task
SCH_Add_Task(TRAFFIC_LIGHTS_Update, 10, 200);
// Start the scheduler
SCU_B_SLAVE_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCH_Init_T2();
// Set up the display
BARGRAPH_Init();
// Set up the switch pin
SWITCH_MS_Init();
// Add a 'SWITCH_MS_Update' task, every ~200 ms
// - timings are in ticks (50 ms tick interval - see Sch 'init' function)
SCH_Add_Task(SWITCH_MS_Update, 0, 4);
// Add a 'COUNTER_Update' task every ~1000 ms
SCH_Add_Task(COUNTER_Update, 0, 20);
SCH_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
/* ............................................................... */
void main(void)
{
// Initialisation can be problematic with some display / supply
// combinations. You may get away with calling this function
// twice (or once) but - for maximum reliability under a very wide range
// of conditions - it is called three times here.
LCD_Init(0);
LCD_Init(0);
LCD_Init(1);
// Prepare the elapsed time library
Elapsed_Time_LCD_Init();
// Prepare the scheduler
SCH_Init_T2();
// Add tasks to the scheduler
//
// Update the time every second (*** 1ms sched ticks ***)
SCH_Add_Task(Elapsed_Time_LCD_Update, 100, 1000);
// Update the whole display ~ every second
// - do this by updating a character once every 24 ms
// (assumes a 40 character display)
SCH_Add_Task(LCD_Update, 1000, 24);
// All tasks added: start running the scheduler
SCH_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCC_A_SLAVE_Init_CAN();
// Set up the flash LED task (demo purposes)
LED_Flash_Init();
// Prepare for the traffic light task
TRAFFIC_LIGHTS_Init();
// TIMING IS IN TICKS (6 ms tick interval)
// Add a 'flash LED' task (on for 1002 ms, off for 1002 ms)
SCH_Add_Task(LED_Flash_Update, 0, 167);
// Add the traffic-light task
SCH_Add_Task(TRAFFIC_LIGHTS_Update, 30, 167);
// Start the scheduler
SCC_A_SLAVE_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCU_A_MASTER_Init_T1_T2(9600);
// Prepare for the traffic light task
TRAFFIC_LIGHTS_Init();
// Prepare for the flash LED task (demo only)
LED_Flash_Init();
// Add a 'flash LED' task (on for 1000 ms, off for 1000 ms)
SCH_Add_Task(LED_Flash_Update, 0, 200);
// Add a 'traffic light' task
SCH_Add_Task(TRAFFIC_LIGHTS_Update, 30, 200);
// Start the scheduler
SCU_A_MASTER_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main()
{
cli(); // disable INT. during peripheral setting
Peripheral_Init();
SCH_Init_T2_1ms(); //初始化systick为1ms
sei(); // enable INT.
SCH_Add_Task(UART0_TX,0,10);
SCH_Start();
// TODO: add your main code here
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(){
SCH_Init_T2();
led_init();
SCH_Add_Task(draw1,0,2);
SCH_Add_Task(draw2,1,2);
SCH_Add_Task(draw,0,34);
SCH_Start();
while(1){
SCH_Dispatch_Tasks();
button();
if(350==count++){
count=0;
move();
}
}
}
void main(void)
{
// Set up the scheduler
SCH_Init_T0();
// Prepare for the 'Flash_LED' task
LED_Flash_Init();
// Add the 'Flash LED' task (on for ~1000 ms, off for ~1000 ms)
// - timings are in ticks (5 ms tick interval)
// (Max interval / delay is 65535 ticks)
SCH_Add_Task(LED_Flash_Update, 0, 200);
// Start the scheduler
SCH_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCH_Init_T2();
// Set baud rate to 9600, using internal baud rate generator
// Generic 8051 version
PC_LINK_IO_Init_Internal(9600);
// We have to schedule this task (10x a second is enough here)
// - this checks if a character has been received by the USART
// - if so, responds appropriately.
//
// TIMING IS IN TICKS NOT MILLISECONDS (1 ms tick interval)
SCH_Add_Task(MENU_Command_Processor,100,100);
SCH_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}
void main(void)
{
// Set up the scheduler
SCH_Init_T2();
// Add the 'Time Update' task (once per second)
// - timings are in ticks (1 ms tick interval)
// (Max interval / delay is 65535 ticks)
SCH_Add_Task(CLOCK_LED_Time_Update,100,10);
// Add the 'Display Update' task (once per second)
// Need to update a 4-segment display every 3 ms (approx)
// Need to update a 2-segment display every 6 ms (approx)
SCH_Add_Task(LED_MX4_Display_Update,0,3);
// Start the scheduler
SCH_Start();
while(1)
{
SCH_Dispatch_Tasks();
}
}