static int cm_fx6_setup_usb_host(void)
{
int err;
err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
if (err)
return err;
SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL));
SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
return 0;
}
static int cm_fx6_init_usb_otg(void)
{
int ret;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
if (ret) {
printf("USB OTG pwr gpio request failed: %d\n", ret);
return ret;
}
SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
MUX_PAD_CTRL(WEAK_PULLDOWN));
clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
/* disable ext. charger detect, or it'll affect signal quality at dp. */
return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
}
static void setup_display(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
int reg;
enable_ipu_clock();
imx_setup_hdmi();
/* Turn on LDB0,IPU,IPU DI0 clocks */
reg = __raw_readl(&mxc_ccm->CCGR3);
reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
writel(reg, &mxc_ccm->CCGR3);
/* set LDB0, LDB1 clk select to 011/011 */
reg = readl(&mxc_ccm->cs2cdr);
reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
|MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
|(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->cs2cdr);
reg = readl(&mxc_ccm->cscmr2);
reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
writel(reg, &mxc_ccm->cscmr2);
reg = readl(&mxc_ccm->chsccdr);
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
<<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->chsccdr);
reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
|IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
|IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
|IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
|IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
|IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
|IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
|IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
|IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
writel(reg, &iomux->gpr[2]);
reg = readl(&iomux->gpr[3]);
reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
| (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
<<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
writel(reg, &iomux->gpr[3]);
/* LVDS Backlight GPIO on LVDS connector - output low */
SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 | DIO_PAD_CFG);
gpio_direction_output(IMX_GPIO_NR(1, 10), 0);
}
static void enable_lvds(struct display_info_t const *dev)
{
struct iomuxc *iomux = (struct iomuxc *)
IOMUXC_BASE_ADDR;
/* set CH0 data width to 24bit (IOMUXC_GPR2:5 0=18bit, 1=24bit) */
u32 reg = readl(&iomux->gpr[2]);
reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT;
writel(reg, &iomux->gpr[2]);
/* Enable Backlight */
gpio_request(IMX_GPIO_NR(1, 10), "bklt_gpio");
gpio_direction_output(IMX_GPIO_NR(1, 10), 0);
gpio_request(IMX_GPIO_NR(1, 18), "bklt_en");
SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 | DIO_PAD_CFG);
gpio_direction_output(IMX_GPIO_NR(1, 18), 1);
}
static void setup_display(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
int reg;
enable_ipu_clock();
imx_setup_hdmi();
reg = readl(&mxc_ccm->chsccdr);
reg |= (CHSCCDR_CLK_SEL_LDB_DI0
<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &mxc_ccm->chsccdr);
/* Disable LCD backlight */
SETUP_IOMUX_PAD(PAD_DI0_PIN4__GPIO4_IO20);
gpio_direction_input(IMX_GPIO_NR(4, 20));
}
static int cm_fx6_usb_hub_reset(void)
{
int err;
err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
if (err) {
printf("USB hub rst gpio request failed: %d\n", err);
return -1;
}
SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
udelay(10);
gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
mdelay(1);
return 0;
}
int board_ehci_hcd_init(int port)
{
u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
switch (port) {
case 0:
return cm_fx6_init_usb_otg();
case 1:
SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
MUX_PAD_CTRL(NO_PAD_CTRL));
/* Set PWR polarity to match power switch's enable polarity */
setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
return cm_fx6_usb_hub_reset();
default:
break;
}
return 0;
}