static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
{
unsigned gpio = (unsigned) spi->controller_data;
unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
int i;
u32 csr;
u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
/* Make sure clock polarity is correct */
for (i = 0; i < spi->master->num_chipselect; i++) {
csr = spi_readl(as, CSR0 + 4 * i);
if ((csr ^ cpol) & SPI_BIT(CPOL))
spi_writel(as, CSR0 + 4 * i, csr ^ SPI_BIT(CPOL));
}
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
gpio, active ? " (high)" : "",
mr);
if (!(cpu_is_at91rm9200() && spi->chip_select == 0))
gpio_set_value(gpio, active);
spi_writel(as, MR, mr);
}
static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
if (atmel_spi_is_v2(as)) {
spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
/* For the low SPI version, there is a issue that PDC transfer
* on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
*/
spi_writel(as, CSR0, asd->csr);
if (as->caps.has_wdrbt) {
spi_writel(as, MR,
SPI_BF(PCS, ~(0x01 << spi->chip_select))
| SPI_BIT(WDRBT)
| SPI_BIT(MODFDIS)
| SPI_BIT(MSTR));
} else {
spi_writel(as, MR,
SPI_BF(PCS, ~(0x01 << spi->chip_select))
| SPI_BIT(MODFDIS)
| SPI_BIT(MSTR));
}
mr = spi_readl(as, MR);
if (as->use_cs_gpios)
gpio_set_value(asd->npcs_pin, active);
} else {
u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
int i;
u32 csr;
/* Make sure clock polarity is correct */
for (i = 0; i < spi->master->num_chipselect; i++) {
csr = spi_readl(as, CSR0 + 4 * i);
if ((csr ^ cpol) & SPI_BIT(CPOL))
spi_writel(as, CSR0 + 4 * i,
csr ^ SPI_BIT(CPOL));
}
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
if (as->use_cs_gpios && spi->chip_select != 0)
gpio_set_value(asd->npcs_pin, active);
spi_writel(as, MR, mr);
}
dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
asd->npcs_pin, active ? " (high)" : "",
mr);
}
static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
if (atmel_spi_is_v2()) {
/*
* Always use CSR0. This ensures that the clock
* switches to the correct idle polarity before we
* toggle the CS.
*/
spi_writel(as, CSR0, asd->csr);
spi_writel(as, MR, SPI_BF(PCS, 0x0e) | SPI_BIT(MODFDIS)
| SPI_BIT(MSTR));
mr = spi_readl(as, MR);
gpio_set_value(asd->npcs_pin, active);
} else {
u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
int i;
u32 csr;
/* Make sure clock polarity is correct */
for (i = 0; i < spi->master->num_chipselect; i++) {
csr = spi_readl(as, CSR0 + 4 * i);
if ((csr ^ cpol) & SPI_BIT(CPOL))
spi_writel(as, CSR0 + 4 * i,
csr ^ SPI_BIT(CPOL));
}
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
if (spi->chip_select != 0)
gpio_set_value(asd->npcs_pin, active);
spi_writel(as, MR, mr);
}
dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
asd->npcs_pin, active ? " (high)" : "",
mr);
}
static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
{
struct atmel_spi_device *asd = spi->controller_state;
unsigned active = spi->mode & SPI_CS_HIGH;
u32 mr;
/* only deactivate *this* device; sometimes transfers to
* another device may be active when this routine is called.
*/
mr = spi_readl(as, MR);
if (~SPI_BFEXT(PCS, mr) & (1 << spi->chip_select)) {
mr = SPI_BFINS(PCS, 0xf, mr);
spi_writel(as, MR, mr);
}
dev_dbg(&spi->dev, "DEactivate %u%s, mr %08x\n",
asd->npcs_pin, active ? " (low)" : "",
mr);
if (!as->use_cs_gpios)
spi_writel(as, CR, SPI_BIT(LASTXFER));
else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
gpio_set_value(asd->npcs_pin, !active);
}
