/** Loads saved non-volatile parameter values from the EEPROM into the parameter table, as needed. */
void V2Params_LoadNonVolatileParamValues(void)
{
/* Read parameter values that are stored in non-volatile EEPROM */
uint8_t ResetPolarity = eeprom_read_byte(&EEPROM_Reset_Polarity);
uint8_t SCKDuration = eeprom_read_byte(&EEPROM_SCK_Duration);
/* Update current parameter table if the EEPROM contents was not blank */
if (ResetPolarity != 0xFF)
V2Params_GetParamFromTable(PARAM_RESET_POLARITY)->ParamValue = ResetPolarity;
/* Update current parameter table if the EEPROM contents was not blank */
if (SCKDuration != 0xFF)
V2Params_GetParamFromTable(PARAM_SCK_DURATION)->ParamValue = SCKDuration;
}
/** Updates any parameter values that are sourced from hardware rather than explicitly set by the host, such as
* VTARGET levels from the ADC on supported AVR models.
*/
void V2Params_UpdateParamValues(void)
{
#if (defined(ADC) && !defined(NO_VTARGET_DETECT))
/* Update VTARGET parameter with the latest ADC conversion of VTARGET on supported AVR models */
V2Params_GetParamFromTable(PARAM_VTARGET)->ParamValue = (((uint16_t)(VTARGET_REF_VOLTS * 10 * VTARGET_SCALE_FACTOR) * ADC_GetResult()) / 1024);
#endif
}
/** Updates any parameter values that are sourced from hardware rather than explicitly set by the host, such as
* VTARGET levels from the ADC on supported AVR models.
*/
void V2Params_UpdateParamValues(void)
{
#if defined(ADC)
/* Update VTARGET parameter with the latest ADC conversion of VTARGET on supported AVR models */
V2Params_GetParamFromTable(PARAM_VTARGET)->ParamValue = ((5 * 10 * ADC_GetResult()) / 1024);
#endif
}
/** Retrieves the current value for a given parameter in the parameter table.
*
* \note This function does not first check for read privileges - if the value is being sent to the host via a
* GET PARAM command, \ref V2Params_GetParameterPrivileges() should be called first to ensure that the
* parameter is host-readable.
*
* \param[in] ParamID Parameter ID whose value is to be retrieved from the table
*
* \return Current value of the parameter in the table, or 0 if not found
*/
uint8_t V2Params_GetParameterValue(const uint8_t ParamID)
{
ParameterItem_t* ParamInfo = V2Params_GetParamFromTable(ParamID);
if (ParamInfo == NULL)
return 0;
return ParamInfo->ParamValue;
}
/** Retrieves the host PC read/write privileges for a given parameter in the parameter table. This should
* be called before calls to \ref V2Params_GetParameterValue() or \ref V2Params_SetParameterValue() when
* getting or setting parameter values in response to requests from the host.
*
* \param[in] ParamID Parameter ID whose privileges are to be retrieved from the table
*
* \return Privileges for the requested parameter, as a mask of \c PARAM_PRIV_* masks
*/
uint8_t V2Params_GetParameterPrivileges(const uint8_t ParamID)
{
ParameterItem_t* ParamInfo = V2Params_GetParamFromTable(ParamID);
if (ParamInfo == NULL)
return 0;
return ParamInfo->ParamPrivileges;
}
/** Sets the value for a given parameter in the parameter table.
*
* \param[in] ParamID Parameter ID whose value is to be set in the table
* \param[in] Value New value to set the parameter to
*
* \return Pointer to the associated parameter information from the parameter table if found, NULL otherwise
*/
void V2Params_SetParameterValue(const uint8_t ParamID, const uint8_t Value)
{
ParameterItem_t* ParamInfo = V2Params_GetParamFromTable(ParamID);
if (ParamInfo == NULL)
return;
ParamInfo->ParamValue = Value;
/* The target RESET line polarity is a non-volatile parameter, save to EEPROM when changed */
if (ParamID == PARAM_RESET_POLARITY)
eeprom_write_byte(&EEPROM_Rest_Polarity, Value);
}
/** Loads saved non-volatile parameter values from the EEPROM into the parameter table, as needed. */
void V2Params_LoadNonVolatileParamValues(void)
{
/* Target RESET line polarity is a non-volatile value, retrieve current parameter value from EEPROM */
V2Params_GetParamFromTable(PARAM_RESET_POLARITY)->ParamValue = eeprom_read_byte(&EEPROM_Reset_Polarity);
}
/** Loads saved non-volatile parameter values from the EEPROM into the parameter table, as needed. */
void V2Params_LoadNonVolatileParamValues(void)
{
/* Target RESET line polarity is a non-volatile value, retrieve current parameter value from EEPROM -
* NB: Cannot call V2Protocol_SetParameterValue() here, as that will cause another EEPROM write! */
V2Params_GetParamFromTable(PARAM_RESET_POLARITY)->ParamValue = eeprom_read_byte(&EEPROM_Rest_Polarity);
}