int rt28xx_init(
IN PRTMP_ADAPTER pAd,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// If dirver doesn't wake up firmware here,
// NICLoadFirmware will hang forever when interface is up again.
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif // PCIE_PS_SUPPORT //
#endif // CONFIG_STA_SUPPORT //
// reset Adapter flags
RTMP_CLEAR_FLAGS(pAd);
// Init BssTab & ChannelInfo tabbles for auto channel select.
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
}
#endif // CONFIG_AP_SUPPORT //
#ifdef DOT11_N_SUPPORT
// Allocate BA Reordering memory
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif // DOT11_N_SUPPORT //
// Make sure MAC gets ready.
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
#ifdef RTMP_MAC_PCI
// To fix driver disable/enable hang issue when radio off
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif // RTMP_MAC_PCI //
// Disable DMA
RT28XXDMADisable(pAd);
// Load 8051 firmware
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
// Disable interrupts here which is as soon as possible
// This statement should never be true. We might consider to remove it later
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif // RTMP_MAC_PCI //
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
// initialize MLME
//
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RMTP_RBUS_SUPPORT //
// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
//
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
// COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
// pAd->bForcePrintTX = TRUE;
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
APInitialize(pAd);
#endif // CONFIG_AP_SUPPORT //
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
//
// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
//
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
// Read parameters from Config File
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
//Init Ba Capability parameters.
// RT28XX_BA_INIT(pAd);
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
// UPdata to HT IE
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //
// after reading Registry, we now know if in AP mode or STA mode
// Load 8051 firmware; crash when FW image not existent
// Status = NICLoadFirmware(pAd);
// if (Status != NDIS_STATUS_SUCCESS)
// break;
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
// We should read EEPROM for all cases. rt2860b
NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif // CONFIG_STA_SUPPORT //
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); //rt2860b
#ifdef RTMP_INTERNAL_TX_ALC
//
// Initialize the desired TSSI table
//
InitDesiredTSSITable(pAd);
#endif // RTMP_INTERNAL_TX_ALC //
// Set PHY to appropriate mode
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
// No valid channels.
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif // AP_QLOAD_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
// APInitialize(pAd);
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //
//
// Initialize RF register to default value
//
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef WMM_ACM_SUPPORT
#ifdef CONFIG_AP_SUPPORT
ACMP_Init(pAd,
pAd->CommonCfg.APEdcaParm.bACM[0],
pAd->CommonCfg.APEdcaParm.bACM[1],
pAd->CommonCfg.APEdcaParm.bACM[2],
pAd->CommonCfg.APEdcaParm.bACM[3], 0);
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
ACMP_Init(pAd);
#endif // CONFIG_STA_SUPPORT //
#endif // WMM_ACM_SUPPORT //
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
//
// Undo everything if it failed
//
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
// NdisMDeregisterInterrupt(&pAd->Interrupt);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
// RTMPFreeAdapter(pAd); // we will free it in disconnect()
}
else if (pAd)
{
// Microsoft HCT require driver send a disconnect event after driver initialization.
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
// pAd->IndicateMediaState = NdisMediaStateDisconnected;
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
// Enable Interrupt first due to we need to scan channel to receive beacons.
RTMP_IRQ_ENABLE(pAd);
// Now Enable RxTx
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
// Let BBP register at 20MHz to do scan
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
// Now we can receive the beacon and do the listen beacon
// use default BW to select channel
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
// If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
// RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);
#endif // DOT11N_DRAFT3 //
#endif // DOT11_N_SUPPORT //
#ifdef RELASE_EXCLUDE
/*
3090, 3090A and 3390 all support hadware tone radar function. But the soluation of those are different.
3090 is the old one.
*/
#endif // RELASE_EXCLUDE //
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif // CONFIG_AP_SUPPORT //
}// end of else
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
INT apidx;
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif //HOSTAPD_SUPPORT//
for (apidx = 0; apidx < pAd->ApCfg.BssidNum; apidx++)
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[apidx].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", apidx));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], apidx, FALSE);
WscInit(pAd, FALSE, apidx);
if (pWscControl->WscEnrolleePinCode == 0)
{
pWscControl->WscEnrolleePinCode = GenerateWpsPinCode(pAd, FALSE, apidx);
pWscControl->WscEnrolleePinCodeLen = 8;
}
}
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
PWSC_CTRL pWscControl = &pAd->StaCfg.WscControl;
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], 0, FALSE);
WscInit(pAd, BSS0);
if (pWscControl->WscEnrolleePinCode == 0)
{
pWscControl->WscEnrolleePinCode = GenerateWpsPinCode(pAd, BSS0);
pWscControl->WscEnrolleePinCodeLen = 8;
}
}
#endif // CONFIG_STA_SUPPORT //
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif // WSC_INCLUDED //
// Set up the Mac address
RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);
// Various AP function init
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
RT28xx_MBSS_Init(pAd, pAd->net_dev);
#endif // MBSS_SUPPORT //
#ifdef WDS_SUPPORT
RT28xx_WDS_Init(pAd, pAd->net_dev);
#endif // WDS_SUPPORT //
#ifdef APCLI_SUPPORT
RT28xx_ApCli_Init(pAd, pAd->net_dev);
#endif // APCLI_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef RTMP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoTurbineDynamicTune(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RTMP_RBUS_SUPPORT //
#ifdef RTMP_RBUS_SUPPORT
#ifdef RT3XXX_ANTENNA_DIVERSITY_SUPPORT
RT3XXX_AntDiversity_Init(pAd);
#endif // RT3XXX_ANTENNA_DIVERSITY_SUPPORT //
#endif // RTMP_RBUS_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif // MAT_SUPPORT //
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif // CLIENT_WDS //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef DOT11Z_TDLS_SUPPORT
TDLS_Table_Init(pAd);
#endif // DOT11Z_TDLS_SUPPORT //
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
// send wireless event to wpa_supplicant for infroming interface up.
RtmpOSWrielessEventSend(pAd, IWEVCUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
#endif // WPA_SUPPLICANT_SUPPORT //
}
#endif // CONFIG_STA_SUPPORT //
#if defined(RT2883) || defined(RT3883)
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (IS_RT2883(pAd) || IS_RT3883(pAd))
{
#ifdef RANGE_EXT_SUPPORT
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980);
#endif // RANGE_EXT_SUPPORT //
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#ifdef STREAM_MODE_SUPPORT
if (pAd->CommonCfg.StreamMode > 0)
{
ULONG streamWord = StreamModeRegVal(pAd);
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR0_L, (ULONG)(pAd->CommonCfg.StreamModeMac[0][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[0][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR0_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[0][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[0][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR1_L, (ULONG)(pAd->CommonCfg.StreamModeMac[1][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[1][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR1_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[1][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[1][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR2_L, (ULONG)(pAd->CommonCfg.StreamModeMac[2][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[2][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR2_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[2][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[2][5] << 8));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR3_L, (ULONG)(pAd->CommonCfg.StreamModeMac[3][0]) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][1] << 8) |
(ULONG)(pAd->CommonCfg.StreamModeMac[3][2] << 16) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][3] << 24));
RTMP_IO_WRITE32(pAd, TX_CHAIN_ADDR3_H, streamWord | (ULONG)(pAd->CommonCfg.StreamModeMac[3][4]) | (ULONG)(pAd->CommonCfg.StreamModeMac[3][5] << 8));
}
#endif // STREAM_MODE_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
if (pAd->CommonCfg.FineAGC)
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
BBPValue |= 0x40; // turn on fine AGC
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
else
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
BBPValue &= ~0x40; // turn off fine AGC
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
#endif // defined(RT2883) || defined(RT3883) //
#ifdef DOT11_N_SUPPORT
#ifdef TXBF_SUPPORT
if (pAd->CommonCfg.ITxBfTimeout)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R179, 0x02);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 0);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, pAd->CommonCfg.ITxBfTimeout & 0xFF);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 1);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, (pAd->CommonCfg.ITxBfTimeout>>8) & 0xFF);
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
if (pAd == NULL)
return FALSE;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
/*#ifdef AUTO_CH_SELECT_ENHANCE*/
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
/*#endif AUTO_CH_SELECT_ENHANCE */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
if (WaitForAsicReady(pAd) != TRUE)
goto err1;
DBGPRINT(RT_DEBUG_TRACE, ("MAC[Ver:Rev=0x%08x]\n", pAd->MACVersion));
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
#ifdef RTMP_MAC_PCI
/* To fix driver disable/enable hang issue when radio off*/
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif /* RTMP_MAC_PCI */
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif /* RTMP_MAC_PCI */
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
#ifdef RT6352
pAd->bCalibrationDone = FALSE;
#endif /* RT6352 */
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RMTP_RBUS_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
if ((pAd->OpMode == OPMODE_AP)
#ifdef P2P_SUPPORT
|| TRUE
#endif /* P2P_SUPPORT */
)
APInitialize(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif /* CONFIG_AP_SUPPORT */
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
if(pAd->CommonCfg.Channel==0)
{
RTMPSetDefaultChannel(pAd);
}
#ifdef CONFIG_STA_SUPPORT
#ifdef CREDENTIAL_STORE
RecoverConnectInfo(pAd);
#endif /* CREDENTIAL_STORE */
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
#ifdef LED_CONTROL_SUPPORT
/* Send LED Setting to MCU */
RTMPInitLEDMode(pAd);
#endif /* LED_CONTROL_SUPPORT */
NICInitAsicFromEEPROM(pAd); /* rt2860b */
#ifdef RT6352
if (IS_RT6352(pAd))
{
RtmpKickOutHwNullFrame(pAd, TRUE, FALSE);
#if defined(RT6352_EP_SUPPORT) || defined(RT6352_EL_SUPPORT)
{
ULONG SysRegValue;
RTMP_SYS_IO_READ32(0xb0000060, &SysRegValue);
if ((SysRegValue & 0x100000) == 0x0)
{
SysRegValue |= 0x100000;
RTMP_SYS_IO_WRITE32(0xb0000060, SysRegValue);
DBGPRINT(RT_DEBUG_ERROR,("Change as GPIO Mode(0x%x)\n", SysRegValue));
}
}
#endif /* defined(RT6352_EP_SUPPORT) || defined(RT6352_EL_SUPPORT) */
/* Do R-Calibration */
R_Calibration(pAd);
#ifdef RTMP_TEMPERATURE_CALIBRATION
/* Temperature Init */
RT6352_Temperature_Init(pAd);
RT6352_TemperatureCalibration(pAd);
#endif /* RTMP_TEMPERATURE_CALIBRATION */
#ifdef RTMP_TEMPERATURE_COMPENSATION
/*
read out tempature reference value (0x80 ~ 0x7F)
TssiPlusBoundaryG [7] [6] [5] [4] [3] [2] [1] [0] (smaller) +
TssiMinusBoundaryG[0] [1] [2] [3] [4] [5] [6] [7] (larger)
*/
RT6352_EEPROM_TSSI_24G_READ(pAd);
/*
pAd->TssiCalibratedOffset:
reference temperature(e2p[D1h])
*/
/* adjust the boundary table by pAd->TssiCalibratedOffset */
RT6352_TssiTableAdjust(pAd);
/* ATE temperature(e2p[77h]) */
RT6352_TssiMpAdjust(pAd);
DBGPRINT(RT_DEBUG_OFF,("E2PROM: G Tssi[-7 .. +7] = %d %d %d %d %d %d %d - %d - %d %d %d %d %d %d %d, offset=%d, tuning=%d\n",
pAd->TssiMinusBoundaryG[7], pAd->TssiMinusBoundaryG[6], pAd->TssiMinusBoundaryG[5],
pAd->TssiMinusBoundaryG[4], pAd->TssiMinusBoundaryG[3], pAd->TssiMinusBoundaryG[2], pAd->TssiMinusBoundaryG[1],
pAd->TssiRefG,
pAd->TssiPlusBoundaryG[1], pAd->TssiPlusBoundaryG[2], pAd->TssiPlusBoundaryG[3], pAd->TssiPlusBoundaryG[4],
pAd->TssiPlusBoundaryG[5], pAd->TssiPlusBoundaryG[6], pAd->TssiPlusBoundaryG[7],
pAd->TssiCalibratedOffset, pAd->bAutoTxAgcG));
#endif /* RTMP_TEMPERATURE_COMPENSATION */
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, TRUE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
/* RF Self TX DC Calibration */
RF_SELF_TXDC_CAL(pAd);
/* Rx DCOC Calibration */
RxDCOC_Calibration(pAd);
/* BandWidth Filter Calibration */
BW_Filter_Calibration(pAd,TRUE);
BW_Filter_Calibration(pAd,FALSE);
/* Do LOFT and IQ Calibration */
LOFT_IQ_Calibration(pAd);
/* DPD_Calibration */
#ifdef RT6352_EP_SUPPORT
if (pAd->bExtPA == FALSE)
#endif /* RT6352_EP_SUPPORT */
{
DoDPDCalibration(pAd);
pAd->DoDPDCurrTemperature = 0x7FFFFFFF;
}
/* Rx DCOC Calibration */
RxDCOC_Calibration(pAd);
/* Do RXIQ Calibration */
RXIQ_Calibration(pAd);
#if defined(RT6352_EP_SUPPORT) || defined(RT6352_EL_SUPPORT)
RT6352_Init_ExtPA_ExtLNA(pAd, FALSE);
#endif /* defined(RT6352_EP_SUPPORT) || defined(RT6352_EL_SUPPORT) */
}
#endif /* RT6352 */
#ifdef RALINK_ATE
if (ATEInit(pAd) != NDIS_STATUS_SUCCESS)
{
DBGPRINT(RT_DEBUG_ERROR, ("%s(): ATE initialization failed !\n", __FUNCTION__));
goto err6;
}
#endif /* RALINK_ATE */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
InitRfPaModeTable(pAd);
#ifdef RTMP_TEMPERATURE_COMPENSATION
/* Temperature compensation, initialize the lookup table */
DBGPRINT(RT_DEBUG_OFF, ("bAutoTxAgcG = %d\n", pAd->bAutoTxAgcG));
if (pAd->chipCap.bTempCompTxALC && pAd->bAutoTxAgcG)
InitLookupTable(pAd);
#endif /* RTMP_TEMPERATURE_COMPENSATION */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif /* AP_QLOAD_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
#ifdef RALINK_ATE
#endif /* RALINK_ATE */
#ifdef CONFIG_AP_SUPPORT
/* Initialize RF register to default value*/
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
#ifdef RT6352
if (IS_RT6352(pAd) && (pAd->TxPowerCtrl.bInternalTxALC == TRUE))
{
RT635xTssiDcCalibration(pAd);
}
#endif /* RT6352 */
#endif /* RTMP_INTERNAL_TX_ALC */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
/* Enable Interrupt first due to we need to scan channel to receive beacons.*/
RTMP_IRQ_ENABLE(pAd);
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/* Let BBP register at 20MHz to do scan */
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
/* Now we can receive the beacon and do the listen beacon*/
/* use default BW to select channel*/
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
/* If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel */
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
/* RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);*/
#endif /* DOT11N_DRAFT3 */
#endif /* DOT11_N_SUPPORT */
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef RT6352
pAd->bCalibrationDone = TRUE;
if (IS_RT6352(pAd))
{
#ifdef DYNAMIC_VGA_SUPPORT
if (pAd->CommonCfg.MO_Cfg.bDyncVGAEnable)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R195, 0x83);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R196, 0x70);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R195, 0x86);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R196, 0x70);
}
#endif /* DYNAMIC_VGA_SUPPORT */
}
#endif /* RT6352 */
}/* end of else*/
/* Set up the Mac address*/
#ifdef CONFIG_AP_SUPPORT
#ifndef P2P_APCLI_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], NULL);
#endif /* P2P_APCLI_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], (PUCHAR)(pAd->StaCfg.dev_name));
#endif /* CONFIG_STA_SUPPORT */
/* Various AP function init*/
#ifdef CONFIG_AP_SUPPORT
#ifdef P2P_SUPPORT
#else
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
#endif /* P2P_SUPPORT */
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
/* RT28xx_MBSS_Init(pAd, pAd->net_dev); os abl move to rt_main_dev.c*/
#endif /* MBSS_SUPPORT */
#ifdef WDS_SUPPORT
/* RT28xx_WDS_Init(pAd, pAd->net_dev);*/
#endif /* WDS_SUPPORT */
#ifdef APCLI_SUPPORT
/* RT28xx_ApCli_Init(pAd, pAd->net_dev);*/
#endif /* APCLI_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef UAPSD_SUPPORT
UAPSD_Init(pAd);
#endif /* UAPSD_SUPPORT */
/* assign function pointers*/
#ifdef MAT_SUPPORT
/* init function pointers, used in OS_ABL */
RTMP_MATOpsInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef RTMP_RBUS_SUPPORT
if (pAd->infType == RTMP_DEV_INF_RBUS)
{
#ifdef VIDEO_TURBINE_SUPPORT
VideoTurbineDynamicTune(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#ifdef RT3XXX_ANTENNA_DIVERSITY_SUPPORT
RT3XXX_AntDiversity_Init(pAd);
#endif /* RT3XXX_ANTENNA_DIVERSITY_SUPPORT */
}
#endif /* RTMP_RBUS_SUPPORT */
#ifdef P2P_SUPPORT
/* RTMP_P2P_Init(pAd, pAd->net_dev); */
#endif /* P2P_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif /* CLIENT_WDS */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef DOT11Z_TDLS_SUPPORT
TDLS_Table_Init(pAd);
#endif /* DOT11Z_TDLS_SUPPORT */
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface up.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* auto-fall back settings */
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980); /* Fallback MCS8->MCS0 */
#ifdef DOT11N_SS3_SUPPORT
if (pAd->CommonCfg.TxStream >= 3)
{
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#endif /* DOT11N_SS3_SUPPORT */
#ifdef STREAM_MODE_SUPPORT
RtmpStreamModeInit(pAd);
#endif /* STREAM_MODE_SUPPORT */
#if defined(RT2883) || defined(RT3883)
if (IS_RT2883(pAd) || IS_RT3883(pAd))
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
if (pAd->CommonCfg.FineAGC)
BBPValue |= 0x40; /* turn on fine AGC*/
else
BBPValue &= ~0x40; /* turn off fine AGC*/
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
#endif /* defined(RT2883) || defined(RT3883) */
#ifdef DOT11_N_SUPPORT
#ifdef TXBF_SUPPORT
if (pAd->CommonCfg.ITxBfTimeout)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R179, 0x02);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 0);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, pAd->CommonCfg.ITxBfTimeout & 0xFF);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 1);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, (pAd->CommonCfg.ITxBfTimeout>>8) & 0xFF);
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
if (pAd == NULL)
return FALSE;
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
if (WaitForAsicReady(pAd) != TRUE)
goto err1;
DBGPRINT(RT_DEBUG_TRACE, ("MAC[Ver:Rev=0x%08x]\n", pAd->MACVersion));
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
#ifdef RTMP_MAC_PCI
#if defined(RT3090) || defined(RT3592) || defined(RT3390) || defined(RT3593) || defined(RT5390) || defined(RT5392) || defined(RT5592)
/*Iverson patch PCIE L1 issue to make sure that driver can be read,write ,BBP and RF register at pcie L.1 level */
if ((IS_RT3090(pAd) || IS_RT3572(pAd) ||IS_RT3390(pAd) || IS_RT3593(pAd)
|| IS_RT5390(pAd) || IS_RT5392(pAd) || IS_RT5592(pAd))
&&pAd->infType==RTMP_DEV_INF_PCIE)
{
UINT32 MacValue = 0;
RTMP_IO_READ32(pAd, AUX_CTRL, &MacValue);
MacValue |= 0x402;
RTMP_IO_WRITE32(pAd, AUX_CTRL, MacValue);
DBGPRINT(RT_DEBUG_TRACE, ("AUX_CTRL = 0x%x\n", MacValue));
}
#endif
/* To fix driver disable/enable hang issue when radio off*/
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif /* RTMP_MAC_PCI */
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif /* RTMP_MAC_PCI */
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RT_SOC_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RT_SOC_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
if ((pAd->OpMode == OPMODE_AP)
)
APInitialize(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif /* CONFIG_AP_SUPPORT */
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
/* Set eeprom related hook functions */
Status = RtmpChipOpsEepromHook(pAd, pAd->infType);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
#ifdef LED_CONTROL_SUPPORT
/* Send LED Setting to MCU */
RTMPInitLEDMode(pAd);
#endif /* LED_CONTROL_SUPPORT */
NICInitAsicFromEEPROM(pAd); /* rt2860b */
#ifdef RALINK_ATE
if (ATEInit(pAd) != NDIS_STATUS_SUCCESS)
{
DBGPRINT(RT_DEBUG_ERROR, ("%s(): ATE initialization failed !\n", __FUNCTION__));
goto err6;
}
#endif /* RALINK_ATE */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
#ifdef RTMP_TEMPERATURE_COMPENSATION
/* Temperature compensation, initialize the lookup table */
DBGPRINT(RT_DEBUG_OFF, ("bAutoTxAgcG = %d\n", pAd->bAutoTxAgcG));
if (pAd->chipCap.bTempCompTxALC && pAd->bAutoTxAgcG)
InitLookupTable(pAd);
#endif /* RTMP_TEMPERATURE_COMPENSATION */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif /* AP_QLOAD_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
#ifdef RALINK_ATE
#ifdef RT5592
#ifdef RTMP_RF_RW_SUPPORT
/* both for RT5572 and RT5592 */
if (IS_RT5592(pAd))
{
RT55x2ATEFilterCalibration(pAd);
}
#endif /* RTMP_RF_RW_SUPPORT */
#endif /* RT5592 */
#endif /* RALINK_ATE */
#ifdef CONFIG_AP_SUPPORT
/* Initialize RF register to default value*/
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif /* CONFIG_AP_SUPPORT */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef CONFIG_TSO_SUPPORT
if (RTMP_TEST_MORE_FLAG(pAd, fRTMP_ADAPTER_TSO_SUPPORT))
RTMPTsoEnable(pAd);
#endif /* CONFIG_TSO_SUPPORT */
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
/* Enable Interrupt first due to we need to scan channel to receive beacons.*/
RTMP_IRQ_ENABLE(pAd);
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/* Let BBP register at 20MHz to do scan */
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
/* Now we can receive the beacon and do the listen beacon*/
/* use default BW to select channel*/
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
/* If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel */
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
/* RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);*/
#endif /* DOT11N_DRAFT3 */
#endif /* DOT11_N_SUPPORT */
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif /* CONFIG_AP_SUPPORT */
}/* end of else*/
/* Set up the Mac address*/
#ifdef CONFIG_AP_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], NULL);
#endif /* CONFIG_AP_SUPPORT */
/* Various AP function init*/
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
/* RT28xx_MBSS_Init(pAd, pAd->net_dev); os abl move to rt_main_dev.c*/
#endif /* MBSS_SUPPORT */
#ifdef WDS_SUPPORT
/* RT28xx_WDS_Init(pAd, pAd->net_dev);*/
#endif /* WDS_SUPPORT */
#ifdef APCLI_SUPPORT
/* RT28xx_ApCli_Init(pAd, pAd->net_dev);*/
#endif /* APCLI_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef UAPSD_SUPPORT
UAPSD_Init(pAd);
#endif /* UAPSD_SUPPORT */
/* assign function pointers*/
#ifdef MAT_SUPPORT
/* init function pointers, used in OS_ABL */
RTMP_MATOpsInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef RT_SOC_SUPPORT
if (pAd->infType == RTMP_DEV_INF_RBUS ||
pAd->infType == RTMP_DEV_INF_PCIE)
{
#ifdef VIDEO_TURBINE_SUPPORT
VideoTurbineDynamicTune(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#ifdef RT3XXX_ANTENNA_DIVERSITY_SUPPORT
RT3XXX_AntDiversity_Init(pAd);
#endif /* RT3XXX_ANTENNA_DIVERSITY_SUPPORT */
}
#endif /* RT_SOC_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif /* CLIENT_WDS */
}
#endif /* CONFIG_AP_SUPPORT */
/* auto-fall back settings */
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980);
#ifdef DOT11N_SS3_SUPPORT
if (pAd->CommonCfg.TxStream >= 3)
{
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#endif /* DOT11N_SS3_SUPPORT */
#ifdef STREAM_MODE_SUPPORT
RtmpStreamModeInit(pAd);
#endif /* STREAM_MODE_SUPPORT */
#if defined(RT2883) || defined(RT3883) || defined(RT3593)
if (IS_RT2883(pAd) || IS_RT3883(pAd) || IS_RT3593(pAd))
{
UINT8 BBPValue = 0;
BBP_IO_READ8_BY_REG_ID(pAd, BBP_R65, &BBPValue);
if (pAd->CommonCfg.FineAGC)
BBPValue |= 0x40; /* turn on fine AGC*/
else
BBPValue &= ~0x40; /* turn off fine AGC*/
BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R65, BBPValue);
}
#endif /* defined(RT2883) || defined(RT3883) || defined(RT3593) */
#ifdef DOT11_N_SUPPORT
#ifdef TXBF_SUPPORT
if (pAd->CommonCfg.ITxBfTimeout)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R179, 0x02);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 0);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, pAd->CommonCfg.ITxBfTimeout & 0xFF);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R180, 1);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R182, (pAd->CommonCfg.ITxBfTimeout>>8) & 0xFF);
}
int rt28xx_init(
IN PRTMP_ADAPTER pAd,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
UINT16 ChipId = 0;
// reset Adapter flags
RTMP_CLEAR_FLAGS(pAd);
// Init BssTab & ChannelInfo tabbles for auto channel select.
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
//#ifdef AUTO_CH_SELECT_ENHANCE
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
//#endif // AUTO_CH_SELECT_ENHANCE //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef DOT11_N_SUPPORT
// Allocate BA Reordering memory
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif // DOT11_N_SUPPORT //
// Make sure MAC gets ready.
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
/* The purpose is to identify RT5390H */
RT28xx_EEPROM_READ16(pAd, 0x00, ChipId);
pAd->ChipId = ChipId;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
#ifdef RT5390
if (IS_RT5390H(pAd))
DBGPRINT(RT_DEBUG_ERROR, ("The chip belongs to 0x%04x\n", pAd->ChipId));
#endif /* RT5390 */
#ifdef SPECIFIC_BCN_BUF_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 1;
if (IS_RT5390(pAd) || IS_RT3593(pAd))
{
pAd->BcnCB.bHighShareMemSupport = 1;
pAd->BcnCB.DYN_HW_BEACON_BASE0 = 0x4000;
pAd->BcnCB.DYN_HW_BEACON_MAX_SIZE = 0x2000;
pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT = 16;
#ifdef MBSS_SUPPORT
#ifdef APCLI_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 8 - MAX_MESH_NUM;
#else
pAd->BcnCB.DYN_MAX_MBSSID_NUM = 16 - MAX_MESH_NUM;
#endif // APCLI_SUPPORT //
#endif // MBSS_SUPPORT //
}
else
{
pAd->BcnCB.bHighShareMemSupport = 0;
pAd->BcnCB.DYN_HW_BEACON_BASE0 = 0x7800;
pAd->BcnCB.DYN_HW_BEACON_MAX_SIZE = 0x1000;
pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT = 8;
#ifdef MBSS_SUPPORT
pAd->BcnCB.DYN_MAX_MBSSID_NUM = (pAd->BcnCB.DYN_HW_BEACON_MAX_COUNT - MAX_MESH_NUM - MAX_APCLI_NUM);
#endif // MBSS_SUPPORT //
}
#endif // SPECIFIC_BCN_BUF_SUPPORT //
#ifdef RTMP_MAC_PCI
#if defined(RT3090) || defined(RT3592) || defined(RT3390) || defined(RT3593) || defined(RT5390)
/*Iverson patch PCIE L1 issue to make sure that driver can be read,write ,BBP and RF register at pcie L.1 level */
if ((IS_RT3090(pAd) || IS_RT3572(pAd) ||
IS_RT3390(pAd) || IS_RT3593(pAd) || IS_RT5390(pAd))&&pAd->infType==RTMP_DEV_INF_PCIE)
{
RTMP_IO_READ32(pAd, AUX_CTRL, &MacCsr0);
MacCsr0 |= 0x402;
RTMP_IO_WRITE32(pAd, AUX_CTRL, MacCsr0);
DBGPRINT(RT_DEBUG_TRACE, ("AUX_CTRL = 0x%x\n", MacCsr0));
}
#endif // RT3090 //
// To fix driver disable/enable hang issue when radio off
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif // RTMP_MAC_PCI //
// Disable DMA
RT28XXDMADisable(pAd);
// Load 8051 firmware
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
// Disable interrupts here which is as soon as possible
// This statement should never be true. We might consider to remove it later
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif // RTMP_MAC_PCI //
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
// initialize MLME
//
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RMTP_RBUS_SUPPORT //
// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
//
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
// COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
// pAd->bForcePrintTX = TRUE;
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
APInitialize(pAd);
#endif // CONFIG_AP_SUPPORT //
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
//
// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
//
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif // CONFIG_AP_SUPPORT //
// Read parameters from Config File
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
//Init Ba Capability parameters.
// RT28XX_BA_INIT(pAd);
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
// UPdata to HT IE
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //
// after reading Registry, we now know if in AP mode or STA mode
// Load 8051 firmware; crash when FW image not existent
// Status = NICLoadFirmware(pAd);
// if (Status != NDIS_STATUS_SUCCESS)
// break;
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
// We should read EEPROM for all cases. rt2860b
NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); //rt2860b
#ifdef RTMP_INTERNAL_TX_ALC
//
// Initialize the desired TSSI table
//
InitDesiredTSSITable(pAd);
#endif // RTMP_INTERNAL_TX_ALC //
#if defined(RT5390) || defined(RT5370)
//
// Temperature compensation, initialize the lookup table
//
DBGPRINT(RT_DEBUG_ERROR, ("IS_RT5392 = %d, bAutoTxAgcG = %d\n", IS_RT5392(pAd), pAd->bAutoTxAgcG));
if (IS_RT5392(pAd) && pAd->bAutoTxAgcG && pAd->CommonCfg.TempComp != 0)
{
InitLookupTable(pAd);
}
#endif // defined(RT5390) || defined(RT5370) //
// Set PHY to appropriate mode
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
// No valid channels.
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif // AP_QLOAD_SUPPORT //
//#ifdef DOT11K_RRM_SUPPORT
// RRM_CfgInit(pAd);
//#endif // DOT11K_RRM_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
// APInitialize(pAd);
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //
#ifdef CONFIG_AP_SUPPORT
//
// Initialize RF register to default value
//
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif // CONFIG_AP_SUPPORT //
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef WMM_ACM_SUPPORT
#ifdef CONFIG_AP_SUPPORT
ACMP_Init(pAd,
pAd->CommonCfg.APEdcaParm.bACM[0],
pAd->CommonCfg.APEdcaParm.bACM[1],
pAd->CommonCfg.APEdcaParm.bACM[2],
pAd->CommonCfg.APEdcaParm.bACM[3], 0);
#endif // CONFIG_AP_SUPPORT //
#endif // WMM_ACM_SUPPORT //
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
//
// Undo everything if it failed
//
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
// NdisMDeregisterInterrupt(&pAd->Interrupt);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
// RTMPFreeAdapter(pAd); // we will free it in disconnect()
}
else if (pAd)
{
// Microsoft HCT require driver send a disconnect event after driver initialization.
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
// Enable Interrupt first due to we need to scan channel to receive beacons.
RTMP_IRQ_ENABLE(pAd);
// Now Enable RxTx
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
// Let BBP register at 20MHz to do scan
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
// Now we can receive the beacon and do the listen beacon
// use default BW to select channel
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
// If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
// RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);
#endif // DOT11N_DRAFT3 //
#endif // DOT11_N_SUPPORT //
#ifdef RT3090
#ifdef TONE_RADAR_DETECT_SUPPORT
if (IS_RT3090A(pAd) || IS_RT3390(pAd) || IS_RT5390(pAd))
pAd->CommonCfg.carrier_func=TONE_RADAR_V2;
else
pAd->CommonCfg.carrier_func=TONE_RADAR_V1;
#endif // TONE_RADAR_DETECT_SUPPORT //
#endif // RT3090 //
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif // CONFIG_AP_SUPPORT //
}// end of else
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
INT apidx;
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif //HOSTAPD_SUPPORT//
for (apidx = 0; apidx < pAd->ApCfg.BssidNum; apidx++)
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[apidx].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", apidx));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], apidx, FALSE);
WscInit(pAd, FALSE, apidx);
}
}
#endif // CONFIG_AP_SUPPORT //
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif // WSC_INCLUDED //
// Set up the Mac address
RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);
// Various AP function init
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
RT28xx_MBSS_Init(pAd, pAd->net_dev);
#endif // MBSS_SUPPORT //
#ifdef WDS_SUPPORT
RT28xx_WDS_Init(pAd, pAd->net_dev);
#endif // WDS_SUPPORT //
#ifdef APCLI_SUPPORT
RT28xx_ApCli_Init(pAd, pAd->net_dev);
#endif // APCLI_SUPPORT //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif // MAT_SUPPORT //
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif // CLIENT_WDS //
}
#endif // CONFIG_AP_SUPPORT //
#ifdef RT33xx
if (IS_RT3390(pAd))
{
RTMP_TxEvmCalibration(pAd);
}
#endif // RT33xx //
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
err6:
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
err3:
RtmpMgmtTaskExit(pAd);
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
err1:
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); // free BA pool
#endif // DOT11_N_SUPPORT //
// shall not set priv to NULL here because the priv didn't been free yet.
//net_dev->priv = 0;
#ifdef INF_AMAZON_SE
err0:
#endif // INF_AMAZON_SE //
#ifdef ST
err0:
#endif // ST //
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
if (pAd == NULL)
return FALSE;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
RtmpChipOpsHook(pAd);
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RMTP_RBUS_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef RTMP_MAC_USB
pAd->CommonCfg.bMultipleIRP = FALSE;
if (pAd->CommonCfg.bMultipleIRP)
pAd->CommonCfg.NumOfBulkInIRP = RX_RING_SIZE;
else
pAd->CommonCfg.NumOfBulkInIRP = 1;
#endif /* RTMP_MAC_USB */
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); /*rt2860b*/
#ifdef CONFIG_STA_SUPPORT
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
/* if (IS_RT3593(pAd))*/
/* {*/
/* Initialize the frequency calibration*/
RTMP_CHIP_ASIC_FREQ_CAL_INIT(pAd);
/* }*/
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
#ifdef RTMP_TEMPERATURE_COMPENSATION
/* Temperature compensation, initialize the lookup table */
DBGPRINT(RT_DEBUG_ERROR, ("IS_RT5392 = %d, bAutoTxAgcG = %d\n", IS_RT5392(pAd), pAd->bAutoTxAgcG));
if (IS_RT5392(pAd) && pAd->bAutoTxAgcG && pAd->CommonCfg.TempComp != 0)
{
InitLookupTable(pAd);
}
#endif /* RTMP_TEMPERATURE_COMPENSATION */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
#ifdef RTMP_MAC_USB
AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x02);
RTMPusecDelay(10000);
#endif /* RTMP_MAC_USB */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef RTMP_MAC_USB
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_REMOVE_IN_PROGRESS);
/* Support multiple BulkIn IRP,*/
/* the value on pAd->CommonCfg.NumOfBulkInIRP may be large than 1.*/
for(index=0; index<pAd->CommonCfg.NumOfBulkInIRP; index++)
{
RTUSBBulkReceive(pAd);
DBGPRINT(RT_DEBUG_TRACE, ("RTUSBBulkReceive!\n" ));
}
#endif /* RTMP_MAC_USB */
}/* end of else*/
/* Set up the Mac address*/
#ifdef CONFIG_STA_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], (PUCHAR)(pAd->StaCfg.dev_name));
#endif /* CONFIG_STA_SUPPORT */
/* Various AP function init*/
/* assign function pointers*/
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface up.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
#ifdef HW_ANTENNA_DIVERSITY_SUPPORT
if (pAd->chipCap.FlgIsHwAntennaDiversitySup == TRUE)
SetHWAntennaDivsersity(pAd, pAd->bHardwareAntennaDivesity);
#endif // HW_ANTENNA_DIVERSITY_SUPPORT //
RTMP_CHIP_SPECIFIC(pAd, RTMP_CHIP_SPEC_STATE_INIT,
RTMP_CHIP_SPEC_INITIALIZATION, NULL, 0);
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
err6:
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
err3:
RtmpMgmtTaskExit(pAd);
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
err1:
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); /* free BA pool*/
#endif /* DOT11_N_SUPPORT */
/* shall not set priv to NULL here because the priv didn't been free yet.*/
/*net_dev->priv = 0;*/
#ifdef INF_AMAZON_SE
err0:
#endif /* INF_AMAZON_SE */
#ifdef ST
err0:
#endif /* ST */
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
if (pAd == NULL)
return FALSE;
#ifdef RT3290
DBGPRINT(RT_DEBUG_OFF, ("MACVersion=0x%x\n", pAd->MACVersion));
if (IS_RT3290(pAd))
{
UINT32 MacRegValue;
OSCCTL_STRUC osCtrl = {.word = 0};
CMB_CTRL_STRUC cmbCtrl = {.word = 0};
WLAN_FUN_CTRL_STRUC WlanFunCtrl = {.word = 0};
RTMPEnableWlan(pAd, TRUE, TRUE);
//
// Too much time for reading efuse(enter/exit L1), and our device will hang up
// Disable L1
//
RTMP_IO_READ32(pAd, WLAN_FUN_CTRL, &WlanFunCtrl.word);
if (WlanFunCtrl.field.WLAN_EN == TRUE)
{
WlanFunCtrl.field.PCIE_APP0_CLK_REQ = TRUE;
RTMP_IO_WRITE32(pAd, WLAN_FUN_CTRL, WlanFunCtrl.word);
}
//Enable ROSC_EN first then CAL_REQ
RTMP_IO_READ32(pAd, OSCCTL, &osCtrl.word);
osCtrl.field.ROSC_EN = TRUE; //HW force
RTMP_IO_WRITE32(pAd, OSCCTL, osCtrl.word);
osCtrl.field.ROSC_EN = TRUE; //HW force
osCtrl.field.CAL_REQ = TRUE;
osCtrl.field.REF_CYCLE = 0x27;
RTMP_IO_WRITE32(pAd, OSCCTL, osCtrl.word);
RTMP_IO_READ32(pAd, CMB_CTRL, &cmbCtrl.word);
pAd->CmbCtrl.word = cmbCtrl.word;
// Overwrite default Coex Parameter
RTMP_IO_READ32(pAd, COEXCFG0, &MacRegValue);
MacRegValue &= ~(0xFF000000);
MacRegValue |= 0x5E000000;
RTMP_IO_WRITE32(pAd, COEXCFG0, MacRegValue);
}
if (IS_RT3290LE(pAd))
{
PLL_CTRL_STRUC PllCtrl;
RTMP_IO_READ32(pAd, PLL_CTRL, &PllCtrl.word);
PllCtrl.field.VCO_FIXED_CURRENT_CONTROL = 0x1;
RTMP_IO_WRITE32(pAd, PLL_CTRL, PllCtrl.word);
}
#endif /* RT3290 */
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
/*#ifdef AUTO_CH_SELECT_ENHANCE*/
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
/*#endif AUTO_CH_SELECT_ENHANCE */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
if (WaitForAsicReady(pAd) != TRUE)
goto err1;
DBGPRINT(RT_DEBUG_TRACE, ("MAC[Ver:Rev=0x%08x]\n", pAd->MACVersion));
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RMTP_RBUS_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
if ((pAd->OpMode == OPMODE_AP)
#ifdef P2P_SUPPORT
|| TRUE
#endif /* P2P_SUPPORT */
)
APInitialize(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif /* CONFIG_AP_SUPPORT */
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
#ifdef CONFIG_STA_SUPPORT
#ifdef CREDENTIAL_STORE
RecoverConnectInfo(pAd);
#endif /* CREDENTIAL_STORE */
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef RTMP_MAC_USB
pAd->CommonCfg.bMultipleIRP = FALSE;
if (pAd->CommonCfg.bMultipleIRP)
pAd->CommonCfg.NumOfBulkInIRP = RX_RING_SIZE;
else
pAd->CommonCfg.NumOfBulkInIRP = 1;
#endif /* RTMP_MAC_USB */
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
#ifdef LED_CONTROL_SUPPORT
/* Send LED Setting to MCU */
RTMPInitLEDMode(pAd);
#endif /* LED_CONTROL_SUPPORT */
NICInitAsicFromEEPROM(pAd); /* rt2860b */
#ifdef RALINK_ATE
if (ATEInit(pAd) != NDIS_STATUS_SUCCESS)
{
DBGPRINT(RT_DEBUG_ERROR, ("%s(): ATE initialization failed !\n", __FUNCTION__));
goto err6;
}
#endif /* RALINK_ATE */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#ifdef CONFIG_STA_SUPPORT
/* Initialize the frequency calibration*/
if (pAd->chipCap.FreqCalibrationSupport)
FrequencyCalibration(pAd);
#endif /* CONFIG_STA_SUPPORT */
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
#ifdef RTMP_TEMPERATURE_COMPENSATION
/* Temperature compensation, initialize the lookup table */
DBGPRINT(RT_DEBUG_OFF, ("bAutoTxAgcG = %d\n", pAd->bAutoTxAgcG));
if (pAd->chipCap.bTempCompTxALC && pAd->bAutoTxAgcG)
InitLookupTable(pAd);
#endif /* RTMP_TEMPERATURE_COMPENSATION */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#ifdef CONFIG_STA_SUPPORT
if (pAd->chipCap.FreqCalibrationSupport)
InitFrequencyCalibration(pAd);
#endif /* CONFIG_STA_SUPPORT */
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif /* AP_QLOAD_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
#ifdef RTMP_MAC_USB
AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x02, FALSE);
RTMPusecDelay(10000);
#endif /* RTMP_MAC_USB */
#ifdef RALINK_ATE
#ifdef RT5592
#ifdef RTMP_RF_RW_SUPPORT
/* both for RT5572 and RT5592 */
if (IS_RT5592(pAd))
{
RT55x2ATEFilterCalibration(pAd);
}
#endif /* RTMP_RF_RW_SUPPORT */
#endif /* RT5592 */
#endif /* RALINK_ATE */
#ifdef CONFIG_AP_SUPPORT
/* Initialize RF register to default value*/
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif /* CONFIG_AP_SUPPORT */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef CONFIG_TSO_SUPPORT
if (RTMP_TEST_MORE_FLAG(pAd, fRTMP_ADAPTER_TSO_SUPPORT))
RTMPTsoEnable(pAd);
#endif /* CONFIG_TSO_SUPPORT */
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
/* Enable Interrupt first due to we need to scan channel to receive beacons.*/
RTMP_IRQ_ENABLE(pAd);
#ifdef RTMP_MAC_USB
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_REMOVE_IN_PROGRESS);
/* Support multiple BulkIn IRP,*/
/* the value on pAd->CommonCfg.NumOfBulkInIRP may be large than 1.*/
for(index=0; index<pAd->CommonCfg.NumOfBulkInIRP; index++)
{
RTUSBBulkReceive(pAd);
DBGPRINT(RT_DEBUG_TRACE, ("RTUSBBulkReceive!\n" ));
}
#endif /* RTMP_MAC_USB */
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/* Let BBP register at 20MHz to do scan */
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
/* Now we can receive the beacon and do the listen beacon*/
/* use default BW to select channel*/
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
/* If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel */
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
/* RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);*/
#endif /* DOT11N_DRAFT3 */
#endif /* DOT11_N_SUPPORT */
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef RTMP_MAC_USB
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_REMOVE_IN_PROGRESS);
/* Support multiple BulkIn IRP,*/
/* the value on pAd->CommonCfg.NumOfBulkInIRP may be large than 1.*/
for(index=0; index<pAd->CommonCfg.NumOfBulkInIRP; index++)
{
RTUSBBulkReceive(pAd);
DBGPRINT(RT_DEBUG_TRACE, ("RTUSBBulkReceive!\n" ));
}
#endif /* RTMP_MAC_USB */
}/* end of else*/
/* Set up the Mac address*/
#ifdef CONFIG_AP_SUPPORT
#ifndef P2P_APCLI_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], NULL);
#endif /* P2P_APCLI_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], (PUCHAR)(pAd->StaCfg.dev_name));
#endif /* CONFIG_STA_SUPPORT */
/* Various AP function init*/
#ifdef CONFIG_AP_SUPPORT
#ifdef P2P_SUPPORT
#else
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
#endif /* P2P_SUPPORT */
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
/* RT28xx_MBSS_Init(pAd, pAd->net_dev); os abl move to rt_main_dev.c*/
#endif /* MBSS_SUPPORT */
#ifdef APCLI_SUPPORT
/* RT28xx_ApCli_Init(pAd, pAd->net_dev);*/
#endif /* APCLI_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef UAPSD_SUPPORT
UAPSD_Init(pAd);
#endif /* UAPSD_SUPPORT */
/* assign function pointers*/
#ifdef MAT_SUPPORT
/* init function pointers, used in OS_ABL */
RTMP_MATOpsInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef P2P_SUPPORT
/* RTMP_P2P_Init(pAd, pAd->net_dev); */
#endif /* P2P_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif /* CLIENT_WDS */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef DOT11Z_TDLS_SUPPORT
TDLS_Table_Init(pAd);
#endif /* DOT11Z_TDLS_SUPPORT */
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface up.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* auto-fall back settings */
#ifdef RANGE_EXTEND
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980);
#endif // RANGE_EXTEND //
#ifdef DOT11N_SS3_SUPPORT
if (pAd->CommonCfg.TxStream >= 3)
{
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#endif /* DOT11N_SS3_SUPPORT */
#ifdef STREAM_MODE_SUPPORT
RtmpStreamModeInit(pAd);
#endif /* STREAM_MODE_SUPPORT */
#ifdef DOT11_N_SUPPORT
#endif /* DOT11_N_SUPPORT */
#ifdef RT3290
if (IS_RT3290(pAd))
{
WLAN_FUN_CTRL_STRUC WlanFunCtrl = {.word = 0};
RTMP_MAC_PWRSV_EN(pAd, TRUE, TRUE);
//
// Too much time for reading efuse(enter/exit L1), and our device will hang up
// Enable L1
//
RTMP_IO_READ32(pAd, WLAN_FUN_CTRL, &WlanFunCtrl.word);
if (WlanFunCtrl.field.WLAN_EN == TRUE)
{
WlanFunCtrl.field.PCIE_APP0_CLK_REQ = FALSE;
RTMP_IO_WRITE32(pAd, WLAN_FUN_CTRL, WlanFunCtrl.word);
}
}
#endif /* RT3290 */
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
/*err7:
APStop(pAd);*/
err6:
#ifdef IGMP_SNOOP_SUPPORT
MultiCastFilterTableReset(&pAd->pMulticastFilterTable);
#endif /* IGMP_SNOOP_SUPPORT */
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
RTMP_TimerListRelease(pAd);
err3:
RtmpMgmtTaskExit(pAd);
#ifdef RTMP_TIMER_TASK_SUPPORT
NdisFreeSpinLock(&pAd->TimerQLock);
#endif /* RTMP_TIMER_TASK_SUPPORT */
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
err1:
#ifdef CONFIG_AP_SUPPORT
/* Free BssTab & ChannelInfo tabbles.*/
AutoChBssTableDestroy(pAd);
ChannelInfoDestroy(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef RT3290
if (IS_RT3290(pAd))
RTMPEnableWlan(pAd, FALSE, FALSE);
#endif /* RT3290 */
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); /* free BA pool*/
#endif /* DOT11_N_SUPPORT */
/* shall not set priv to NULL here because the priv didn't been free yet.*/
/*net_dev->priv = 0;*/
#ifdef INF_AMAZON_SE
err0:
#endif /* INF_AMAZON_SE */
#ifdef ST
err0:
#endif /* ST */
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
VOID RTMPDrvOpen(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
/* Enable Interrupt*/
RTMP_IRQ_ENABLE(pAd);
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
{
UINT32 reg = 0;
RTMP_IO_READ32(pAd, 0x1300, ®); /* clear garbage interrupts*/
printk("0x1300 = %08x\n", reg);
}
{
/* u32 reg;*/
/* UINT8 byte;*/
/* u16 tmp;*/
/* RTMP_IO_READ32(pAd, XIFS_TIME_CFG, ®);*/
/* tmp = 0x0805;*/
/* reg = (reg & 0xffff0000) | tmp;*/
/* RTMP_IO_WRITE32(pAd, XIFS_TIME_CFG, reg);*/
}
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
RTMPInitPCIeLinkCtrlValue(pAd);
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
#ifdef BG_FT_SUPPORT
BG_FTPH_Init();
#endif /* BG_FT_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
/*
To reduce connection time,
do auto reconnect here instead of waiting STAMlmePeriodicExec to do auto reconnect.
*/
if (pAd->OpMode == OPMODE_STA)
MlmeAutoReconnectLastSSID(pAd);
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
if ((pAd->OpMode == OPMODE_AP)
#ifdef P2P_SUPPORT
/* P2P will use ApCfg.MBSSID and ApCfg.ApCliTab also. */
|| TRUE
#endif /* P2P_SUPPORT */
)
{
int index;
for (index = 0; index < pAd->ApCfg.BssidNum; index++)
{
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.MBSSID[index].Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif /*HOSTAPD_SUPPORT*/
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[index].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", index));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], index, FALSE);
WscInit(pAd, FALSE, index);
}
}
#ifdef APCLI_SUPPORT
for(index = 0; index < MAX_APCLI_NUM; index++)
{
PWSC_CTRL pWpsCtrl = &pAd->ApCfg.ApCliTab[index].WscControl;
pWpsCtrl->pAd = pAd;
NdisZeroMemory(pWpsCtrl->EntryAddr, MAC_ADDR_LEN);
pWpsCtrl->WscConfigMethods= 0x018C;
RTMP_AP_IoctlHandle(pAd, NULL, CMD_RTPRIV_IOCTL_WSC_INIT, 0, (VOID *)&pAd->ApCfg.ApCliTab[index], index);
}
#endif /* APCLI_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
PWSC_CTRL pWscControl = &pAd->StaCfg.WscControl;
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], 0, FALSE);
WscInit(pAd, FALSE, BSS0);
#ifdef WSC_V2_SUPPORT
WscInitRegistrarPair(pAd, &pAd->StaCfg.WscControl, BSS0);
#endif /* WSC_V2_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif /* WSC_INCLUDED */
}
VOID RTMPDrvClose(
IN VOID *pAdSrc,
IN VOID *net_dev)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
BOOLEAN Cancelled;
UINT32 i = 0;
Cancelled = FALSE;
#ifdef CONFIG_STA_SUPPORT
#ifdef CREDENTIAL_STORE
if (pAd->IndicateMediaState == NdisMediaStateConnected)
{
StoreConnectInfo(pAd);
}
else
{
RTMP_SEM_LOCK(&pAd->StaCtIf.Lock);
pAd->StaCtIf.Changeable = FALSE;
RTMP_SEM_UNLOCK(&pAd->StaCtIf.Lock);
}
#endif /* CREDENTIAL_STORE */
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
#ifdef BG_FT_SUPPORT
BG_FTPH_Remove();
#endif /* BG_FT_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef PCIE_PS_SUPPORT
RTMPPCIeLinkCtrlValueRestore(pAd, RESTORE_CLOSE);
#endif /* PCIE_PS_SUPPORT */
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE))
{
AsicForceWakeup(pAd, TRUE);
}
#ifdef RTMP_MAC_USB
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_REMOVE_IN_PROGRESS);
#endif /* RTMP_MAC_USB */
}
#endif /* CONFIG_STA_SUPPORT */
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS);
#ifdef EXT_BUILD_CHANNEL_LIST
if (pAd->CommonCfg.pChDesp != NULL)
os_free_mem(NULL, pAd->CommonCfg.pChDesp);
pAd->CommonCfg.pChDesp = NULL;
pAd->CommonCfg.DfsType = MAX_RD_REGION;
pAd->CommonCfg.bCountryFlag = 0;
#endif /* EXT_BUILD_CHANNEL_LIST */
for (i = 0 ; i < NUM_OF_TX_RING; i++)
{
while (pAd->DeQueueRunning[i] == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Waiting for TxQueue[%d] done..........\n", i));
RTMPusecDelay(1000);
}
}
#ifdef RTMP_MAC_USB
RtmpOsUsbEmptyUrbCheck(&pAd->wait, &pAd->BulkInLock, &pAd->PendingRx);
#endif /* RTMP_MAC_USB */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef RTMP_MAC_USB
RTMPCancelTimer(&pAd->CommonCfg.BeaconUpdateTimer, &Cancelled);
#endif /* RTMP_MAC_USB */
#ifdef DOT11N_DRAFT3
if (pAd->CommonCfg.Bss2040CoexistFlag & BSS_2040_COEXIST_TIMER_FIRED)
{
RTMPCancelTimer(&pAd->CommonCfg.Bss2040CoexistTimer, &Cancelled);
pAd->CommonCfg.Bss2040CoexistFlag = 0;
}
#endif /* DOT11N_DRAFT3 */
/* PeriodicTimer already been canceled by MlmeHalt() API.*/
/*RTMPCancelTimer(&pAd->PeriodicTimer, &Cancelled);*/
}
#endif /* CONFIG_AP_SUPPORT */
/* Stop Mlme state machine*/
MlmeHalt(pAd);
/* Close net tasklets*/
RtmpNetTaskExit(pAd);
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
MacTableReset(pAd);
#ifdef MAT_SUPPORT
MATEngineExit(pAd);
#endif /* MAT_SUPPORT */
#if defined(WOW_SUPPORT) && defined(RTMP_MAC_USB) && defined(WOW_IFDOWN_SUPPORT)
if (pAd->WOW_Cfg.bEnable == TRUE)
RT28xxUsbAsicWOWEnable(pAd);
else
#endif /* WOW_SUPPORT */
MlmeRadioOff(pAd);
}
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineExit(pAd);
#endif /* MAT_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabDestory(pAd);
#endif /* CLIENT_WDS */
/* Shutdown Access Point function, release all related resources */
APShutdown(pAd);
/*#ifdef AUTO_CH_SELECT_ENHANCE*/
/* Free BssTab & ChannelInfo tabbles.*/
/* AutoChBssTableDestroy(pAd); */
/* ChannelInfoDestroy(pAd); */
/*#endif AUTO_CH_SELECT_ENHANCE */
}
#endif /* CONFIG_AP_SUPPORT */
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
#ifdef LED_CONTROL_SUPPORT
RTMPExitLEDMode(pAd);
#endif // LED_CONTROL_SUPPORT
/* Close kernel threads*/
RtmpMgmtTaskExit(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
/* must after RtmpMgmtTaskExit(); Or pAd->pChannelInfo will be NULL */
/* Free BssTab & ChannelInfo tabbles.*/
AutoChBssTableDestroy(pAd);
ChannelInfoDestroy(pAd);
}
#endif /* CONFIG_AP_SUPPORT */
/* Free IRQ*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* Free Ring or USB buffers*/
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
/* Free Ring or USB buffers*/
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS);
#ifdef DOT11_N_SUPPORT
/* Free BA reorder resource*/
ba_reordering_resource_release(pAd);
#endif /* DOT11_N_SUPPORT */
UserCfgExit(pAd); /* must after ba_reordering_resource_release */
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/*+++Modify by woody to solve the bulk fail+++*/
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef RT35xx
if (IS_RT3572(pAd))
{
RT30xxWriteRFRegister(pAd, RF_R08, 0x00);
AsicSendCommandToMcu(pAd, 0x30, 0xff, 0xff, 0x02, FALSE);
}
#endif /* RT35xx */
#ifdef DOT11Z_TDLS_SUPPORT
TDLS_Table_Destory(pAd);
#ifdef TDLS_AUTOLINK_SUPPORT
TDLS_ClearEntryList(&pAd->StaCfg.TdlsInfo.TdlsDiscovPeerList);
NdisFreeSpinLock(&pAd->StaCfg.TdlsInfo.TdlsDiscovPeerListSemLock);
TDLS_ClearEntryList(&pAd->StaCfg.TdlsInfo.TdlsBlackList);
NdisFreeSpinLock(&pAd->StaCfg.TdlsInfo.TdlsBlackListSemLock);
#endif /* TDLS_AUTOLINK_SUPPORT */
#endif /* DOT11Z_TDLS_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* clear MAC table */
/* TODO: do not clear spin lock, such as fLastChangeAccordingMfbLock */
NdisZeroMemory(&pAd->MacTab, sizeof(MAC_TABLE));
/* release all timers */
RTMPusecDelay(2000);
RTMP_TimerListRelease(pAd);
#ifdef RTMP_TIMER_TASK_SUPPORT
NdisFreeSpinLock(&pAd->TimerQLock);
#endif /* RTMP_TIMER_TASK_SUPPORT */
}
VOID RTMPInfClose(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
#ifdef CONFIG_AP_SUPPORT
pAd->ApCfg.MBSSID[MAIN_MBSSID].bBcnSntReq = FALSE;
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
/* kick out all STAs behind the bss.*/
MbssKickOutStas(pAd, MAIN_MBSSID, REASON_DISASSOC_INACTIVE);
}
#ifdef RT_CFG80211_SUPPORT
#else
APMakeAllBssBeacon(pAd);
APUpdateAllBeaconFrame(pAd);
#endif /* RT_CFG80211_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef PROFILE_STORE
WriteDatThread(pAd);
RTMPusecDelay(1000);
#endif /* PROFILE_STORE */
#ifdef QOS_DLS_SUPPORT
/* send DLS-TEAR_DOWN message, */
if (pAd->CommonCfg.bDLSCapable)
{
UCHAR i;
/* tear down local dls table entry*/
for (i=0; i<MAX_NUM_OF_INIT_DLS_ENTRY; i++)
{
if (pAd->StaCfg.DLSEntry[i].Valid && (pAd->StaCfg.DLSEntry[i].Status == DLS_FINISH))
{
RTMPSendDLSTearDownFrame(pAd, pAd->StaCfg.DLSEntry[i].MacAddr);
pAd->StaCfg.DLSEntry[i].Status = DLS_NONE;
pAd->StaCfg.DLSEntry[i].Valid = FALSE;
}
}
/* tear down peer dls table entry*/
for (i=MAX_NUM_OF_INIT_DLS_ENTRY; i<MAX_NUM_OF_DLS_ENTRY; i++)
{
if (pAd->StaCfg.DLSEntry[i].Valid && (pAd->StaCfg.DLSEntry[i].Status == DLS_FINISH))
{
RTMPSendDLSTearDownFrame(pAd, pAd->StaCfg.DLSEntry[i].MacAddr);
pAd->StaCfg.DLSEntry[i].Status = DLS_NONE;
pAd->StaCfg.DLSEntry[i].Valid = FALSE;
}
}
RTMP_MLME_HANDLER(pAd);
}
#endif /* QOS_DLS_SUPPORT */
if (INFRA_ON(pAd) &&
#if defined(WOW_SUPPORT) && defined(RTMP_MAC_USB) && defined(WOW_IFDOWN_SUPPORT) /* In WOW state, can't issue disassociation reqeust */
pAd->WOW_Cfg.bEnable == FALSE &&
#endif /* WOW_SUPPORT */
(!RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST)))
{
MLME_DISASSOC_REQ_STRUCT DisReq;
MLME_QUEUE_ELEM *MsgElem;/* = (MLME_QUEUE_ELEM *) kmalloc(sizeof(MLME_QUEUE_ELEM), MEM_ALLOC_FLAG);*/
os_alloc_mem(NULL, (UCHAR **)&MsgElem, sizeof(MLME_QUEUE_ELEM));
if (MsgElem)
{
COPY_MAC_ADDR(DisReq.Addr, pAd->CommonCfg.Bssid);
DisReq.Reason = REASON_DEAUTH_STA_LEAVING;
MsgElem->Machine = ASSOC_STATE_MACHINE;
MsgElem->MsgType = MT2_MLME_DISASSOC_REQ;
MsgElem->MsgLen = sizeof(MLME_DISASSOC_REQ_STRUCT);
NdisMoveMemory(MsgElem->Msg, &DisReq, sizeof(MLME_DISASSOC_REQ_STRUCT));
/* Prevent to connect AP again in STAMlmePeriodicExec*/
pAd->MlmeAux.AutoReconnectSsidLen= 32;
NdisZeroMemory(pAd->MlmeAux.AutoReconnectSsid, pAd->MlmeAux.AutoReconnectSsidLen);
pAd->Mlme.CntlMachine.CurrState = CNTL_WAIT_OID_DISASSOC;
MlmeDisassocReqAction(pAd, MsgElem);
/* kfree(MsgElem);*/
os_free_mem(NULL, MsgElem);
}
RTMPusecDelay(1000);
}
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface down.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_DOWN, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
if (pAd->StaCfg.pWpsProbeReqIe)
{
/* kfree(pAd->StaCfg.pWpsProbeReqIe);*/
os_free_mem(NULL, pAd->StaCfg.pWpsProbeReqIe);
pAd->StaCfg.pWpsProbeReqIe = NULL;
pAd->StaCfg.WpsProbeReqIeLen = 0;
}
if (pAd->StaCfg.pWpaAssocIe)
{
/* kfree(pAd->StaCfg.pWpaAssocIe);*/
os_free_mem(NULL, pAd->StaCfg.pWpaAssocIe);
pAd->StaCfg.pWpaAssocIe = NULL;
pAd->StaCfg.WpaAssocIeLen = 0;
}
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
}
PNET_DEV RtmpPhyNetDevMainCreate(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
PNET_DEV pDevNew;
UINT32 MC_RowID = 0, IoctlIF = 0;
pAd = pAd;
#ifdef MULTIPLE_CARD_SUPPORT
MC_RowID = pAd->MC_RowID;
#endif /* MULTIPLE_CARD_SUPPORT */
#ifdef HOSTAPD_SUPPORT
IoctlIF = pAd->IoctlIF;
#endif /* HOSTAPD_SUPPORT */
pDevNew = RtmpOSNetDevCreate((INT32)MC_RowID, (UINT32 *)&IoctlIF,
INT_MAIN, 0, sizeof(PRTMP_ADAPTER), INF_MAIN_DEV_NAME);
#ifdef HOSTAPD_SUPPORT
pAd->IoctlIF = IoctlIF;
#endif /* HOSTAPD_SUPPORT */
return pDevNew;
}
int rt28xx_init(
IN PRTMP_ADAPTER pAd,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// If dirver doesn't wake up firmware here,
// NICLoadFirmware will hang forever when interface is up again.
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif // PCIE_PS_SUPPORT //
#endif // CONFIG_STA_SUPPORT //
// reset Adapter flags
RTMP_CLEAR_FLAGS(pAd);
// Init BssTab & ChannelInfo tabbles for auto channel select.
#ifdef DOT11_N_SUPPORT
// Allocate BA Reordering memory
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif // DOT11_N_SUPPORT //
// Make sure MAC gets ready.
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
}
while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
// Disable DMA
RT28XXDMADisable(pAd);
// Load 8051 firmware
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
// Disable interrupts here which is as soon as possible
// This statement should never be true. We might consider to remove it later
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
// initialize MLME
//
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif // VIDEO_TURBINE_SUPPORT //
#endif // RMTP_RBUS_SUPPORT //
// Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default
//
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
// COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);
// pAd->bForcePrintTX = TRUE;
CfgInitHook(pAd);
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif // BLOCK_NET_IF //
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n", Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n", Status));
goto err6;
}
//
// Init the hardware, we need to init asic before read registry, otherwise mac register will be reset
//
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
// Read parameters from Config File
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n", Status));
goto err6;
}
#ifdef RTMP_MAC_USB
pAd->CommonCfg.bMultipleIRP = FALSE;
if (pAd->CommonCfg.bMultipleIRP)
pAd->CommonCfg.NumOfBulkInIRP = RX_RING_SIZE;
else
pAd->CommonCfg.NumOfBulkInIRP = 1;
#endif // RTMP_MAC_USB //
#ifdef DOT11_N_SUPPORT
//Init Ba Capability parameters.
// RT28XX_BA_INIT(pAd);
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
// UPdata to HT IE
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif // DOT11_N_SUPPORT //
// after reading Registry, we now know if in AP mode or STA mode
// Load 8051 firmware; crash when FW image not existent
// Status = NICLoadFirmware(pAd);
// if (Status != NDIS_STATUS_SUCCESS)
// break;
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
// We should read EEPROM for all cases. rt2860b
NICReadEEPROMParameters(pAd, (PUCHAR)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif // CONFIG_STA_SUPPORT //
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
NICInitAsicFromEEPROM(pAd); //rt2860b
#ifdef RTMP_INTERNAL_TX_ALC
//
// Initialize the desired TSSI table
//
InitDesiredTSSITable(pAd);
#endif // RTMP_INTERNAL_TX_ALC //
// Set PHY to appropriate mode
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif // DOT11_N_SUPPORT //
// No valid channels.
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif // DOT11_N_SUPPORT //
// APInitialize(pAd);
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif // IKANOS_VX_1X0 //
#ifdef RTMP_MAC_USB
AsicSendCommandToMcu(pAd, 0x31, 0xff, 0x00, 0x02);
RTMPusecDelay(10000);
#endif // RTMP_MAC_USB //
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
//
// Undo everything if it failed
//
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
// NdisMDeregisterInterrupt(&pAd->Interrupt);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
// RTMPFreeAdapter(pAd); // we will free it in disconnect()
}
else if (pAd)
{
// Microsoft HCT require driver send a disconnect event after driver initialization.
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef RTMP_MAC_USB
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_RESET_IN_PROGRESS);
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_REMOVE_IN_PROGRESS);
//
// Support multiple BulkIn IRP,
// the value on pAd->CommonCfg.NumOfBulkInIRP may be large than 1.
//
for (index = 0; index < pAd->CommonCfg.NumOfBulkInIRP; index++)
{
RTUSBBulkReceive(pAd);
DBGPRINT(RT_DEBUG_TRACE, ("RTUSBBulkReceive!\n"));
}
#endif // RTMP_MAC_USB //
}// end of else
// Set up the Mac address
RtmpOSNetDevAddrSet(pAd->net_dev, &pAd->CurrentAddress[0]);
// Various AP function init
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
// send wireless event to wpa_supplicant for infroming interface up.
RtmpOSWrielessEventSend(pAd, IWEVCUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
#endif // WPA_SUPPLICANT_SUPPORT //
}
#endif // CONFIG_STA_SUPPORT //
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
err6:
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
err3:
RtmpMgmtTaskExit(pAd);
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif // RESOURCE_PRE_ALLOC //
err1:
#ifdef DOT11_N_SUPPORT
if (pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); // free BA pool
#endif // DOT11_N_SUPPORT //
// shall not set priv to NULL here because the priv didn't been free yet.
//net_dev->priv = 0;
#ifdef INF_AMAZON_SE
err0:
#endif // INF_AMAZON_SE //
#ifdef ST
err0:
#endif // ST //
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
UINT32 MacCsr0 = 0;
if (pAd == NULL)
return FALSE;
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
/*#ifdef AUTO_CH_SELECT_ENHANCE*/
AutoChBssTableInit(pAd);
ChannelInfoInit(pAd);
/*#endif AUTO_CH_SELECT_ENHANCE */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
do
{
RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
pAd->MACVersion = MacCsr0;
if ((pAd->MACVersion != 0x00) && (pAd->MACVersion != 0xFFFFFFFF))
break;
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST))
goto err1;
RTMPusecDelay(10);
} while (index++ < 100);
DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
RtmpChipOpsHook(pAd);
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
#ifdef RTMP_MAC_PCI
/* To fix driver disable/enable hang issue when radio off*/
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif /* RTMP_MAC_PCI */
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif /* RTMP_MAC_PCI */
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RMTP_RBUS_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
APInitialize(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
}
#endif /* CONFIG_AP_SUPPORT */
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
#ifdef LED_CONTROL_SUPPORT
/* Send LED Setting to MCU */
RTMPInitLEDMode(pAd);
#endif /* LED_CONTROL_SUPPORT */
NICInitAsicFromEEPROM(pAd); /*rt2860b*/
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
/* if (IS_RT3593(pAd))*/
/* {*/
/* Initialize the frequency calibration*/
RTMP_CHIP_ASIC_FREQ_CAL_INIT(pAd);
/* }*/
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef AP_QLOAD_SUPPORT
/* init QBSS Element */
QBSS_LoadInit(pAd);
#endif /* AP_QLOAD_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
#ifdef CONFIG_AP_SUPPORT
/* Initialize RF register to default value*/
if (pAd->OpMode == OPMODE_AP)
{
AsicSwitchChannel(pAd, pAd->CommonCfg.Channel, FALSE);
AsicLockChannel(pAd, pAd->CommonCfg.Channel);
}
#endif /* CONFIG_AP_SUPPORT */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
if (pAd->ApCfg.bAutoChannelAtBootup || (pAd->CommonCfg.Channel == 0))
{
UINT8 BBPValue = 0;
/* Enable Interrupt first due to we need to scan channel to receive beacons.*/
RTMP_IRQ_ENABLE(pAd);
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/* Let BBP register at 20MHz to do scan */
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
BBPValue &= (~0x18);
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
DBGPRINT(RT_DEBUG_ERROR, ("SYNC - BBP R4 to 20MHz.l\n"));
/* Now we can receive the beacon and do the listen beacon*/
/* use default BW to select channel*/
pAd->CommonCfg.Channel = AP_AUTO_CH_SEL(pAd, pAd->ApCfg.AutoChannelAlg);
pAd->ApCfg.bAutoChannelAtBootup = FALSE;
}
#ifdef DOT11_N_SUPPORT
/* If phymode > PHY_11ABGN_MIXED and BW=40 check extension channel, after select channel */
N_ChannelCheck(pAd);
#ifdef DOT11N_DRAFT3
/*
We only do this Overlapping BSS Scan when system up, for the
other situation of channel changing, we depends on station's
report to adjust ourself.
*/
if (pAd->CommonCfg.bForty_Mhz_Intolerant == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Disable 20/40 BSSCoex Channel Scan(BssCoex=%d, 40MHzIntolerant=%d)\n",
pAd->CommonCfg.bBssCoexEnable,
pAd->CommonCfg.bForty_Mhz_Intolerant));
}
else if(pAd->CommonCfg.bBssCoexEnable == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Enable 20/40 BSSCoex Channel Scan(BssCoex=%d)\n",
pAd->CommonCfg.bBssCoexEnable));
APOverlappingBSSScan(pAd);
}
RTMP_11N_D3_TimerInit(pAd);
/* RTMPInitTimer(pAd, &pAd->CommonCfg.Bss2040CoexistTimer, GET_TIMER_FUNCTION(Bss2040CoexistTimeOut), pAd, FALSE);*/
#endif /* DOT11N_DRAFT3 */
#endif /* DOT11_N_SUPPORT */
APStartUp(pAd);
DBGPRINT(RT_DEBUG_OFF, ("Main bssid = %02x:%02x:%02x:%02x:%02x:%02x\n",
PRINT_MAC(pAd->ApCfg.MBSSID[BSS0].Bssid)));
}
#endif /* CONFIG_AP_SUPPORT */
}/* end of else*/
#ifdef WSC_INCLUDED
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
INT apidx;
for (apidx = 0; apidx < pAd->ApCfg.BssidNum; apidx++)
{
#ifdef HOSTAPD_SUPPORT
if (pAd->ApCfg.MBSSID[apidx].Hostapd == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("WPS is control by hostapd now.\n"));
}
else
#endif /*HOSTAPD_SUPPORT*/
{
PWSC_CTRL pWscControl;
UCHAR zeros16[16]= {0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0};
pWscControl = &pAd->ApCfg.MBSSID[apidx].WscControl;
DBGPRINT(RT_DEBUG_TRACE, ("Generate UUID for apidx(%d)\n", apidx));
if (NdisEqualMemory(&pWscControl->Wsc_Uuid_E[0], zeros16, UUID_LEN_HEX))
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], apidx, FALSE);
WscInit(pAd, FALSE, apidx);
}
}
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
PWSC_CTRL pWscControl = &pAd->StaCfg.WscControl;
WscGenerateUUID(pAd, &pWscControl->Wsc_Uuid_E[0], &pWscControl->Wsc_Uuid_Str[0], 0, FALSE);
WscInit(pAd, FALSE, BSS0);
#ifdef WSC_V2_SUPPORT
WscInitRegistrarPair(pAd, &pAd->StaCfg.WscControl, BSS0);
#endif /* WSC_V2_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* WSC hardware push button function 0811 */
WSC_HDR_BTN_Init(pAd);
#endif /* WSC_INCLUDED */
/* Set up the Mac address*/
#ifdef CONFIG_AP_SUPPORT
#ifndef P2P_APCLI_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], NULL);
#endif /* P2P_APCLI_SUPPORT */
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], (PUCHAR)(pAd->StaCfg.dev_name));
#endif /* CONFIG_STA_SUPPORT */
/* Various AP function init*/
#ifdef CONFIG_AP_SUPPORT
#ifdef P2P_SUPPORT
#else
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
#endif /* P2P_SUPPORT */
{
#ifdef MBSS_SUPPORT
/* the function can not be moved to RT2860_probe() even register_netdev()
is changed as register_netdevice().
Or in some PC, kernel will panic (Fedora 4) */
/* RT28xx_MBSS_Init(pAd, pAd->net_dev); os abl move to rt_main_dev.c*/
#endif /* MBSS_SUPPORT */
#ifdef WDS_SUPPORT
/* RT28xx_WDS_Init(pAd, pAd->net_dev);*/
#endif /* WDS_SUPPORT */
#ifdef APCLI_SUPPORT
/* RT28xx_ApCli_Init(pAd, pAd->net_dev);*/
#endif /* APCLI_SUPPORT */
#ifdef UAPSD_AP_SUPPORT
UAPSD_Init(pAd);
#endif /* UAPSD_AP_SUPPORT */
}
#endif /* CONFIG_AP_SUPPORT */
/* assign function pointers*/
#ifdef MAT_SUPPORT
/* init function pointers, used in OS_ABL */
RTMP_MATOpsInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef RTMP_RBUS_SUPPORT
#ifdef RT3XXX_ANTENNA_DIVERSITY_SUPPORT
RT3XXX_AntDiversity_Init(pAd);
#endif /* RT3XXX_ANTENNA_DIVERSITY_SUPPORT */
#endif /* RTMP_RBUS_SUPPORT */
#ifdef P2P_SUPPORT
/* RTMP_P2P_Init(pAd, pAd->net_dev); */
#endif /* P2P_SUPPORT */
#ifdef CONFIG_AP_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_AP(pAd)
{
#ifdef MAT_SUPPORT
MATEngineInit(pAd);
#endif /* MAT_SUPPORT */
#ifdef CLIENT_WDS
CliWds_ProxyTabInit(pAd);
#endif /* CLIENT_WDS */
}
#endif /* CONFIG_AP_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface up.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
#ifdef RTMP_RBUS_SUPPORT
#ifdef DOT11_N_SUPPORT
#endif /* DOT11_N_SUPPORT */
#endif /* RTMP_RBUS_SUPPORT */
#ifdef HW_ANTENNA_DIVERSITY_SUPPORT
if (pAd->chipCap.FlgIsHwAntennaDiversitySup == TRUE)
SetHWAntennaDivsersity(pAd, pAd->bHardwareAntennaDivesity);
#endif // HW_ANTENNA_DIVERSITY_SUPPORT //
RTMP_CHIP_SPECIFIC(pAd, RTMP_CHIP_SPEC_STATE_INIT,
RTMP_CHIP_SPEC_INITIALIZATION, NULL, 0);
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
err6:
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
err3:
RtmpMgmtTaskExit(pAd);
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
err1:
#ifdef CONFIG_AP_SUPPORT
/* Free BssTab & ChannelInfo tabbles.*/
AutoChBssTableDestroy(pAd);
ChannelInfoDestroy(pAd);
#endif /* CONFIG_AP_SUPPORT */
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); /* free BA pool*/
#endif /* DOT11_N_SUPPORT */
/* shall not set priv to NULL here because the priv didn't been free yet.*/
/*net_dev->priv = 0;*/
#ifdef INF_AMAZON_SE
err0:
#endif /* INF_AMAZON_SE */
#ifdef ST
err0:
#endif /* ST */
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
RTMP_BUILD_DRV_OPS_FUNCTION_BODY
#endif /* OS_ABL_FUNC_SUPPORT */
#endif /* LINUX */
int rt28xx_init(
IN VOID *pAdSrc,
IN PSTRING pDefaultMac,
IN PSTRING pHostName)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
UINT index;
UCHAR TmpPhy;
NDIS_STATUS Status;
if (pAd == NULL)
return FALSE;
#ifdef RT3290
DBGPRINT(RT_DEBUG_OFF, ("MACVersion=0x%x\n", pAd->MACVersion));
if (IS_RT3290(pAd))
{
UINT32 MacRegValue;
OSCCTL_STRUC osCtrl = {.word = 0};
CMB_CTRL_STRUC cmbCtrl = {.word = 0};
WLAN_FUN_CTRL_STRUC WlanFunCtrl = {.word = 0};
RTMPEnableWlan(pAd, TRUE, TRUE);
//
// Too much time for reading efuse(enter/exit L1), and our device will hang up
// Disable L1
//
RTMP_IO_READ32(pAd, WLAN_FUN_CTRL, &WlanFunCtrl.word);
if (WlanFunCtrl.field.WLAN_EN == TRUE)
{
WlanFunCtrl.field.PCIE_APP0_CLK_REQ = TRUE;
RTMP_IO_WRITE32(pAd, WLAN_FUN_CTRL, WlanFunCtrl.word);
}
//Enable ROSC_EN first then CAL_REQ
RTMP_IO_READ32(pAd, OSCCTL, &osCtrl.word);
osCtrl.field.ROSC_EN = TRUE; //HW force
RTMP_IO_WRITE32(pAd, OSCCTL, osCtrl.word);
osCtrl.field.ROSC_EN = TRUE; //HW force
osCtrl.field.CAL_REQ = TRUE;
osCtrl.field.REF_CYCLE = 0x27;
RTMP_IO_WRITE32(pAd, OSCCTL, osCtrl.word);
RTMP_IO_READ32(pAd, CMB_CTRL, &cmbCtrl.word);
pAd->CmbCtrl.word = cmbCtrl.word;
// Overwrite default Coex Parameter
RTMP_IO_READ32(pAd, COEXCFG0, &MacRegValue);
MacRegValue &= ~(0xFF000000);
MacRegValue |= 0x5E000000;
RTMP_IO_WRITE32(pAd, COEXCFG0, MacRegValue);
}
if (IS_RT3290LE(pAd))
{
PLL_CTRL_STRUC PllCtrl;
RTMP_IO_READ32(pAd, PLL_CTRL, &PllCtrl.word);
PllCtrl.field.VCO_FIXED_CURRENT_CONTROL = 0x1;
RTMP_IO_WRITE32(pAd, PLL_CTRL, PllCtrl.word);
}
#endif /* RT3290 */
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE) &&
OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_ADVANCE_POWER_SAVE_PCIE_DEVICE))
{
AUTO_WAKEUP_STRUC AutoWakeupCfg;
AsicForceWakeup(pAd, TRUE);
AutoWakeupCfg.word = 0;
RTMP_IO_WRITE32(pAd, AUTO_WAKEUP_CFG, AutoWakeupCfg.word);
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_DOZE);
}
}
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
/* reset Adapter flags*/
RTMP_CLEAR_FLAGS(pAd);
/* Init BssTab & ChannelInfo tabbles for auto channel select.*/
#ifdef DOT11_N_SUPPORT
/* Allocate BA Reordering memory*/
if (ba_reordering_resource_init(pAd, MAX_REORDERING_MPDU_NUM) != TRUE)
goto err1;
#endif /* DOT11_N_SUPPORT */
/* Make sure MAC gets ready.*/
index = 0;
if (WaitForAsicReady(pAd) != TRUE)
goto err1;
DBGPRINT(RT_DEBUG_TRACE, ("MAC[Ver:Rev=0x%08x]\n", pAd->MACVersion));
if (MAX_LEN_OF_MAC_TABLE > MAX_AVAILABLE_CLIENT_WCID(pAd))
{
DBGPRINT(RT_DEBUG_ERROR, ("MAX_LEN_OF_MAC_TABLE can not be larger than MAX_AVAILABLE_CLIENT_WCID!!!!\n"));
goto err1;
}
#ifdef RTMP_MAC_PCI
#if defined(RT3090) || defined(RT3592) || defined(RT3390) || defined(RT3593) || defined(RT5390) || defined(RT5392) || defined(RT5592)
/*Iverson patch PCIE L1 issue to make sure that driver can be read,write ,BBP and RF register at pcie L.1 level */
if ((IS_RT3090(pAd) || IS_RT3572(pAd) ||IS_RT3390(pAd) || IS_RT3593(pAd)
|| IS_RT5390(pAd) || IS_RT5392(pAd) || IS_RT5592(pAd))
&&pAd->infType==RTMP_DEV_INF_PCIE)
{
UINT32 MacValue = 0;
RTMP_IO_READ32(pAd, AUX_CTRL, &MacValue);
MacValue |= 0x402;
RTMP_IO_WRITE32(pAd, AUX_CTRL, MacValue);
DBGPRINT(RT_DEBUG_TRACE, ("AUX_CTRL = 0x%x\n", MacValue));
}
#endif
/* To fix driver disable/enable hang issue when radio off*/
RTMP_IO_WRITE32(pAd, PWR_PIN_CFG, 0x2);
#endif /* RTMP_MAC_PCI */
/* Disable DMA*/
RT28XXDMADisable(pAd);
/* Load 8051 firmware*/
Status = NICLoadFirmware(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICLoadFirmware failed, Status[=0x%08x]\n", Status));
goto err1;
}
NICLoadRateSwitchingParams(pAd);
/* Disable interrupts here which is as soon as possible*/
/* This statement should never be true. We might consider to remove it later*/
#ifdef RTMP_MAC_PCI
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
#endif /* RTMP_MAC_PCI */
#ifdef RESOURCE_PRE_ALLOC
Status = RTMPInitTxRxRingMemory(pAd);
#else
Status = RTMPAllocTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPAllocTxRxMemory failed, Status[=0x%08x]\n", Status));
goto err2;
}
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
/* initialize MLME*/
Status = RtmpMgmtTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err3;
Status = MlmeInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MlmeInit failed, Status[=0x%08x]\n", Status));
goto err4;
}
#ifdef RMTP_RBUS_SUPPORT
#ifdef VIDEO_TURBINE_SUPPORT
VideoConfigInit(pAd);
#endif /* VIDEO_TURBINE_SUPPORT */
#endif /* RMTP_RBUS_SUPPORT */
/* Initialize pAd->StaCfg, pAd->ApCfg, pAd->CommonCfg to manufacture default*/
UserCfgInit(pAd);
Status = RtmpNetTaskInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
goto err5;
/* COPY_MAC_ADDR(pAd->ApCfg.MBSSID[apidx].Bssid, netif->hwaddr);*/
/* pAd->bForcePrintTX = TRUE;*/
CfgInitHook(pAd);
#ifdef BLOCK_NET_IF
initblockQueueTab(pAd);
#endif /* BLOCK_NET_IF */
Status = MeasureReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("MeasureReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
Status = TpcReqTabInit(pAd);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("TpcReqTabInit failed, Status[=0x%08x]\n",Status));
goto err6;
}
/* Init the hardware, we need to init asic before read registry, otherwise mac register will be reset*/
Status = NICInitializeAdapter(pAd, TRUE);
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("NICInitializeAdapter failed, Status[=0x%08x]\n", Status));
if (Status != NDIS_STATUS_SUCCESS)
goto err6;
}
/* Read parameters from Config File */
/* unknown, it will be updated in NICReadEEPROMParameters */
pAd->RfIcType = RFIC_UNKNOWN;
Status = RTMPReadParametersHook(pAd);
#ifdef CONFIG_STA_SUPPORT
#ifdef CREDENTIAL_STORE
RecoverConnectInfo(pAd);
#endif /* CREDENTIAL_STORE */
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("1. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
if (Status != NDIS_STATUS_SUCCESS)
{
DBGPRINT_ERR(("RTMPReadParametersHook failed, Status[=0x%08x]\n",Status));
goto err6;
}
#ifdef DOT11_N_SUPPORT
/*Init Ba Capability parameters.*/
/* RT28XX_BA_INIT(pAd);*/
pAd->CommonCfg.DesiredHtPhy.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
pAd->CommonCfg.DesiredHtPhy.AmsduEnable = (USHORT)pAd->CommonCfg.BACapability.field.AmsduEnable;
pAd->CommonCfg.DesiredHtPhy.AmsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.DesiredHtPhy.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
/* UPdata to HT IE*/
pAd->CommonCfg.HtCapability.HtCapInfo.MimoPs = (USHORT)pAd->CommonCfg.BACapability.field.MMPSmode;
pAd->CommonCfg.HtCapability.HtCapInfo.AMsduSize = (USHORT)pAd->CommonCfg.BACapability.field.AmsduSize;
pAd->CommonCfg.HtCapability.HtCapParm.MpduDensity = (UCHAR)pAd->CommonCfg.BACapability.field.MpduDensity;
#endif /* DOT11_N_SUPPORT */
/* after reading Registry, we now know if in AP mode or STA mode*/
/* Load 8051 firmware; crash when FW image not existent*/
/* Status = NICLoadFirmware(pAd);*/
/* if (Status != NDIS_STATUS_SUCCESS)*/
/* break;*/
DBGPRINT(RT_DEBUG_OFF, ("2. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
/* We should read EEPROM for all cases. rt2860b*/
NICReadEEPROMParameters(pAd, (PSTRING)pDefaultMac);
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
DBGPRINT(RT_DEBUG_OFF, ("3. Phy Mode = %d\n", pAd->CommonCfg.PhyMode));
#ifdef LED_CONTROL_SUPPORT
/* Send LED Setting to MCU */
RTMPInitLEDMode(pAd);
#endif /* LED_CONTROL_SUPPORT */
NICInitAsicFromEEPROM(pAd); /* rt2860b */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#ifdef CONFIG_STA_SUPPORT
/* Initialize the frequency calibration*/
if (pAd->chipCap.FreqCalibrationSupport)
FrequencyCalibration(pAd);
#endif /* CONFIG_STA_SUPPORT */
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
#ifdef RTMP_INTERNAL_TX_ALC
/* Initialize the desired TSSI table*/
RTMP_CHIP_ASIC_TSSI_TABLE_INIT(pAd);
#endif /* RTMP_INTERNAL_TX_ALC */
#ifdef RTMP_TEMPERATURE_COMPENSATION
/* Temperature compensation, initialize the lookup table */
DBGPRINT(RT_DEBUG_OFF, ("bAutoTxAgcG = %d\n", pAd->bAutoTxAgcG));
if (pAd->chipCap.bTempCompTxALC && pAd->bAutoTxAgcG)
InitLookupTable(pAd);
#endif /* RTMP_TEMPERATURE_COMPENSATION */
#ifdef RTMP_FREQ_CALIBRATION_SUPPORT
#ifdef CONFIG_STA_SUPPORT
if (pAd->chipCap.FreqCalibrationSupport)
InitFrequencyCalibration(pAd);
#endif /* CONFIG_STA_SUPPORT */
#endif /* RTMP_FREQ_CALIBRATION_SUPPORT */
/* Set PHY to appropriate mode*/
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
#endif /* DOT11_N_SUPPORT */
/* No valid channels.*/
if (pAd->ChannelListNum == 0)
{
DBGPRINT(RT_DEBUG_ERROR, ("Wrong configuration. No valid channel found. Check \"ContryCode\" and \"ChannelGeography\" setting.\n"));
goto err6;
}
#ifdef DOT11_N_SUPPORT
DBGPRINT(RT_DEBUG_OFF, ("MCS Set = %02x %02x %02x %02x %02x\n", pAd->CommonCfg.HtCapability.MCSSet[0],
pAd->CommonCfg.HtCapability.MCSSet[1], pAd->CommonCfg.HtCapability.MCSSet[2],
pAd->CommonCfg.HtCapability.MCSSet[3], pAd->CommonCfg.HtCapability.MCSSet[4]));
#endif /* DOT11_N_SUPPORT */
/* APInitialize(pAd);*/
#ifdef IKANOS_VX_1X0
VR_IKANOS_FP_Init(pAd->ApCfg.BssidNum, pAd->PermanentAddress);
#endif /* IKANOS_VX_1X0 */
/*
Some modules init must be called before APStartUp().
Or APStartUp() will make up beacon content and call
other modules API to get some information to fill.
*/
#ifdef CONFIG_TSO_SUPPORT
if (RTMP_TEST_MORE_FLAG(pAd, fRTMP_ADAPTER_TSO_SUPPORT))
RTMPTsoEnable(pAd);
#endif /* CONFIG_TSO_SUPPORT */
if (pAd && (Status != NDIS_STATUS_SUCCESS))
{
/* Undo everything if it failed*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
/* NdisMDeregisterInterrupt(&pAd->Interrupt);*/
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* RTMPFreeAdapter(pAd); we will free it in disconnect()*/
}
else if (pAd)
{
/* Microsoft HCT require driver send a disconnect event after driver initialization.*/
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_MEDIA_STATE_CONNECTED);
OPSTATUS_CLEAR_FLAG(pAd, fOP_AP_STATUS_MEDIA_STATE_CONNECTED);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_MEDIA_STATE_CHANGE);
DBGPRINT(RT_DEBUG_TRACE, ("NDIS_STATUS_MEDIA_DISCONNECT Event B!\n"));
}/* end of else*/
/* Set up the Mac address*/
#ifdef CONFIG_STA_SUPPORT
RtmpOSNetDevAddrSet(pAd->OpMode, pAd->net_dev, &pAd->CurrentAddress[0], (PUCHAR)(pAd->StaCfg.dev_name));
#endif /* CONFIG_STA_SUPPORT */
/* Various AP function init*/
#ifdef UAPSD_SUPPORT
UAPSD_Init(pAd);
#endif /* UAPSD_SUPPORT */
/* assign function pointers*/
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface up.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_UP, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
/* auto-fall back settings */
#ifdef RANGE_EXTEND
RTMP_IO_WRITE32(pAd, HT_FBK_CFG1, 0xedcba980);
#endif // RANGE_EXTEND //
#ifdef DOT11N_SS3_SUPPORT
if (pAd->CommonCfg.TxStream >= 3)
{
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_0, 0x12111008);
RTMP_IO_WRITE32(pAd, TX_FBK_CFG_3S_1, 0x16151413);
}
#endif /* DOT11N_SS3_SUPPORT */
#ifdef STREAM_MODE_SUPPORT
RtmpStreamModeInit(pAd);
#endif /* STREAM_MODE_SUPPORT */
#ifdef DOT11_N_SUPPORT
#endif /* DOT11_N_SUPPORT */
#ifdef RT3290
if (IS_RT3290(pAd))
{
WLAN_FUN_CTRL_STRUC WlanFunCtrl = {.word = 0};
RTMP_MAC_PWRSV_EN(pAd, TRUE, TRUE);
//
// Too much time for reading efuse(enter/exit L1), and our device will hang up
// Enable L1
//
RTMP_IO_READ32(pAd, WLAN_FUN_CTRL, &WlanFunCtrl.word);
if (WlanFunCtrl.field.WLAN_EN == TRUE)
{
WlanFunCtrl.field.PCIE_APP0_CLK_REQ = FALSE;
RTMP_IO_WRITE32(pAd, WLAN_FUN_CTRL, WlanFunCtrl.word);
}
}
#endif /* RT3290 */
DBGPRINT_S(Status, ("<==== rt28xx_init, Status=%x\n", Status));
return TRUE;
/*err7:
APStop(pAd);*/
err6:
#ifdef IGMP_SNOOP_SUPPORT
MultiCastFilterTableReset(&pAd->pMulticastFilterTable);
#endif /* IGMP_SNOOP_SUPPORT */
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
err5:
RtmpNetTaskExit(pAd);
UserCfgExit(pAd);
err4:
MlmeHalt(pAd);
RTMP_TimerListRelease(pAd);
err3:
RtmpMgmtTaskExit(pAd);
#ifdef RTMP_TIMER_TASK_SUPPORT
NdisFreeSpinLock(&pAd->TimerQLock);
#endif /* RTMP_TIMER_TASK_SUPPORT */
err2:
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
err1:
#ifdef RT3290
if (IS_RT3290(pAd))
RTMPEnableWlan(pAd, FALSE, FALSE);
#endif /* RT3290 */
#ifdef DOT11_N_SUPPORT
if(pAd->mpdu_blk_pool.mem)
os_free_mem(pAd, pAd->mpdu_blk_pool.mem); /* free BA pool*/
#endif /* DOT11_N_SUPPORT */
/* shall not set priv to NULL here because the priv didn't been free yet.*/
/*net_dev->priv = 0;*/
#ifdef INF_AMAZON_SE
err0:
#endif /* INF_AMAZON_SE */
#ifdef ST
err0:
#endif /* ST */
DBGPRINT(RT_DEBUG_ERROR, ("!!! rt28xx Initialized fail !!!\n"));
return FALSE;
}
VOID RTMPDrvOpen(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
/* Enable Interrupt*/
RTMP_IRQ_ENABLE(pAd);
/* Now Enable RxTx*/
RTMPEnableRxTx(pAd);
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_START_UP);
{
UINT32 reg = 0;
RTMP_IO_READ32(pAd, 0x1300, ®); /* clear garbage interrupts*/
printk("0x1300 = %08x\n", reg);
}
{
/* u32 reg;*/
/* UINT8 byte;*/
/* u16 tmp;*/
/* RTMP_IO_READ32(pAd, XIFS_TIME_CFG, ®);*/
/* tmp = 0x0805;*/
/* reg = (reg & 0xffff0000) | tmp;*/
/* RTMP_IO_WRITE32(pAd, XIFS_TIME_CFG, reg);*/
}
#ifdef CONFIG_STA_SUPPORT
#ifdef PCIE_PS_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
RTMPInitPCIeLinkCtrlValue(pAd);
#endif /* PCIE_PS_SUPPORT */
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
/*
To reduce connection time,
do auto reconnect here instead of waiting STAMlmePeriodicExec to do auto reconnect.
*/
if (pAd->OpMode == OPMODE_STA)
MlmeAutoReconnectLastSSID(pAd);
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
}
VOID RTMPDrvClose(
IN VOID *pAdSrc,
IN VOID *net_dev)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
BOOLEAN Cancelled;
UINT32 i = 0;
Cancelled = FALSE;
#ifdef CONFIG_STA_SUPPORT
#ifdef CREDENTIAL_STORE
if (pAd->IndicateMediaState == NdisMediaStateConnected)
{
StoreConnectInfo(pAd);
}
else
{
RTMP_SEM_LOCK(&pAd->StaCtIf.Lock);
pAd->StaCtIf.Changeable = FALSE;
RTMP_SEM_UNLOCK(&pAd->StaCtIf.Lock);
}
#endif /* CREDENTIAL_STORE */
#endif /* CONFIG_STA_SUPPORT */
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef PCIE_PS_SUPPORT
RTMPPCIeLinkCtrlValueRestore(pAd, RESTORE_CLOSE);
#endif /* PCIE_PS_SUPPORT */
/* If dirver doesn't wake up firmware here,*/
/* NICLoadFirmware will hang forever when interface is up again.*/
if (OPSTATUS_TEST_FLAG(pAd, fOP_STATUS_DOZE))
{
AsicForceWakeup(pAd, TRUE);
}
#ifdef RTMP_MAC_PCI
pAd->bPCIclkOff = FALSE;
#endif /* RTMP_MAC_PCI */
}
#endif /* CONFIG_STA_SUPPORT */
RTMP_SET_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS);
#ifdef EXT_BUILD_CHANNEL_LIST
if (pAd->CommonCfg.pChDesp != NULL)
os_free_mem(NULL, pAd->CommonCfg.pChDesp);
pAd->CommonCfg.pChDesp = NULL;
pAd->CommonCfg.DfsType = MAX_RD_REGION;
pAd->CommonCfg.bCountryFlag = 0;
#endif /* EXT_BUILD_CHANNEL_LIST */
#ifdef WDS_SUPPORT
WdsDown(pAd);
#endif /* WDS_SUPPORT */
for (i = 0 ; i < NUM_OF_TX_RING; i++)
{
while (pAd->DeQueueRunning[i] == TRUE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Waiting for TxQueue[%d] done..........\n", i));
RTMPusecDelay(1000);
}
}
/* Stop Mlme state machine*/
MlmeHalt(pAd);
/* Close net tasklets*/
RtmpNetTaskExit(pAd);
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
MacTableReset(pAd);
#if defined(WOW_SUPPORT) && defined(RTMP_MAC_USB) && defined(WOW_IFDOWN_SUPPORT)
if (pAd->WOW_Cfg.bEnable == TRUE)
RT28xxUsbAsicWOWEnable(pAd);
else
#endif /* WOW_SUPPORT */
MlmeRadioOff(pAd);
}
#endif /* CONFIG_STA_SUPPORT */
MeasureReqTabExit(pAd);
TpcReqTabExit(pAd);
#ifdef LED_CONTROL_SUPPORT
RTMPExitLEDMode(pAd);
#endif // LED_CONTROL_SUPPORT
/* Close kernel threads*/
RtmpMgmtTaskExit(pAd);
#ifdef RTMP_MAC_PCI
{
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_ACTIVE))
{
RTMP_ASIC_INTERRUPT_DISABLE(pAd);
}
/* Receive packets to clear DMA index after disable interrupt. */
/*RTMPHandleRxDoneInterrupt(pAd);*/
/* put to radio off to save power when driver unload. After radiooff, can't write /read register. So need to finish all */
/* register access before Radio off.*/
#ifdef RTMP_PCI_SUPPORT
if (pAd->infType == RTMP_DEV_INF_PCI || pAd->infType == RTMP_DEV_INF_PCIE)
{
BOOLEAN brc;
brc=RT28xxPciAsicRadioOff(pAd, RTMP_HALT, 0);
/*In solution 3 of 3090F, the bPCIclkOff will be set to TRUE after calling RT28xxPciAsicRadioOff*/
#ifdef PCIE_PS_SUPPORT
pAd->bPCIclkOff = FALSE;
#endif /* PCIE_PS_SUPPORT */
if (brc==FALSE)
{
DBGPRINT(RT_DEBUG_ERROR,("%s call RT28xxPciAsicRadioOff fail !!\n", __FUNCTION__));
}
}
#endif /* RTMP_PCI_SUPPORT */
}
#endif /* RTMP_MAC_PCI */
/* Free IRQ*/
if (RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE))
{
#ifdef RTMP_MAC_PCI
/* Deregister interrupt function*/
RTMP_OS_IRQ_RELEASE(pAd, net_dev);
#endif /* RTMP_MAC_PCI */
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_INTERRUPT_IN_USE);
}
/* Free Ring or USB buffers*/
#ifdef RESOURCE_PRE_ALLOC
RTMPResetTxRxRingMemory(pAd);
#else
/* Free Ring or USB buffers*/
RTMPFreeTxRxRingMemory(pAd);
#endif /* RESOURCE_PRE_ALLOC */
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_HALT_IN_PROGRESS);
#ifdef DOT11_N_SUPPORT
/* Free BA reorder resource*/
ba_reordering_resource_release(pAd);
#endif /* DOT11_N_SUPPORT */
UserCfgExit(pAd); /* must after ba_reordering_resource_release */
#ifdef CONFIG_STA_SUPPORT
#endif /* CONFIG_STA_SUPPORT */
RTMP_CLEAR_FLAG(pAd, fRTMP_ADAPTER_START_UP);
/*+++Modify by woody to solve the bulk fail+++*/
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
}
#endif /* CONFIG_STA_SUPPORT */
/* clear MAC table */
/* TODO: do not clear spin lock, such as fLastChangeAccordingMfbLock */
NdisZeroMemory(&pAd->MacTab, sizeof(MAC_TABLE));
/* release all timers */
RTMPusecDelay(2000);
RTMP_TimerListRelease(pAd);
#ifdef RTMP_TIMER_TASK_SUPPORT
NdisFreeSpinLock(&pAd->TimerQLock);
#endif /* RTMP_TIMER_TASK_SUPPORT */
}
VOID RTMPInfClose(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
#ifdef CONFIG_STA_SUPPORT
IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
#ifdef PROFILE_STORE
WriteDatThread(pAd);
RTMPusecDelay(1000);
#endif /* PROFILE_STORE */
#ifdef QOS_DLS_SUPPORT
/* send DLS-TEAR_DOWN message, */
if (pAd->CommonCfg.bDLSCapable)
{
UCHAR i;
/* tear down local dls table entry*/
for (i=0; i<MAX_NUM_OF_INIT_DLS_ENTRY; i++)
{
if (pAd->StaCfg.DLSEntry[i].Valid && (pAd->StaCfg.DLSEntry[i].Status == DLS_FINISH))
{
RTMPSendDLSTearDownFrame(pAd, pAd->StaCfg.DLSEntry[i].MacAddr);
pAd->StaCfg.DLSEntry[i].Status = DLS_NONE;
pAd->StaCfg.DLSEntry[i].Valid = FALSE;
}
}
/* tear down peer dls table entry*/
for (i=MAX_NUM_OF_INIT_DLS_ENTRY; i<MAX_NUM_OF_DLS_ENTRY; i++)
{
if (pAd->StaCfg.DLSEntry[i].Valid && (pAd->StaCfg.DLSEntry[i].Status == DLS_FINISH))
{
RTMPSendDLSTearDownFrame(pAd, pAd->StaCfg.DLSEntry[i].MacAddr);
pAd->StaCfg.DLSEntry[i].Status = DLS_NONE;
pAd->StaCfg.DLSEntry[i].Valid = FALSE;
}
}
RTMP_MLME_HANDLER(pAd);
}
#endif /* QOS_DLS_SUPPORT */
if (INFRA_ON(pAd) &&
#if defined(WOW_SUPPORT) && defined(RTMP_MAC_USB) && defined(WOW_IFDOWN_SUPPORT) /* In WOW state, can't issue disassociation reqeust */
pAd->WOW_Cfg.bEnable == FALSE &&
#endif /* WOW_SUPPORT */
(!RTMP_TEST_FLAG(pAd, fRTMP_ADAPTER_NIC_NOT_EXIST)))
{
MLME_DISASSOC_REQ_STRUCT DisReq;
MLME_QUEUE_ELEM *MsgElem;/* = (MLME_QUEUE_ELEM *) kmalloc(sizeof(MLME_QUEUE_ELEM), MEM_ALLOC_FLAG);*/
os_alloc_mem(NULL, (UCHAR **)&MsgElem, sizeof(MLME_QUEUE_ELEM));
if (MsgElem)
{
COPY_MAC_ADDR(DisReq.Addr, pAd->CommonCfg.Bssid);
DisReq.Reason = REASON_DEAUTH_STA_LEAVING;
MsgElem->Machine = ASSOC_STATE_MACHINE;
MsgElem->MsgType = MT2_MLME_DISASSOC_REQ;
MsgElem->MsgLen = sizeof(MLME_DISASSOC_REQ_STRUCT);
NdisMoveMemory(MsgElem->Msg, &DisReq, sizeof(MLME_DISASSOC_REQ_STRUCT));
/* Prevent to connect AP again in STAMlmePeriodicExec*/
pAd->MlmeAux.AutoReconnectSsidLen= 32;
NdisZeroMemory(pAd->MlmeAux.AutoReconnectSsid, pAd->MlmeAux.AutoReconnectSsidLen);
pAd->Mlme.CntlMachine.CurrState = CNTL_WAIT_OID_DISASSOC;
MlmeDisassocReqAction(pAd, MsgElem);
/* kfree(MsgElem);*/
os_free_mem(NULL, MsgElem);
}
RTMPusecDelay(1000);
}
#ifdef WPA_SUPPLICANT_SUPPORT
#ifndef NATIVE_WPA_SUPPLICANT_SUPPORT
/* send wireless event to wpa_supplicant for infroming interface down.*/
RtmpOSWrielessEventSend(pAd->net_dev, RT_WLAN_EVENT_CUSTOM, RT_INTERFACE_DOWN, NULL, NULL, 0);
#endif /* NATIVE_WPA_SUPPLICANT_SUPPORT */
if (pAd->StaCfg.pWpsProbeReqIe)
{
/* kfree(pAd->StaCfg.pWpsProbeReqIe);*/
os_free_mem(NULL, pAd->StaCfg.pWpsProbeReqIe);
pAd->StaCfg.pWpsProbeReqIe = NULL;
pAd->StaCfg.WpsProbeReqIeLen = 0;
}
if (pAd->StaCfg.pWpaAssocIe)
{
/* kfree(pAd->StaCfg.pWpaAssocIe);*/
os_free_mem(NULL, pAd->StaCfg.pWpaAssocIe);
pAd->StaCfg.pWpaAssocIe = NULL;
pAd->StaCfg.WpaAssocIeLen = 0;
}
#endif /* WPA_SUPPLICANT_SUPPORT */
}
#endif /* CONFIG_STA_SUPPORT */
}
PNET_DEV RtmpPhyNetDevMainCreate(
IN VOID *pAdSrc)
{
PRTMP_ADAPTER pAd = (PRTMP_ADAPTER)pAdSrc;
PNET_DEV pDevNew;
UINT32 MC_RowID = 0, IoctlIF = 0;
pAd = pAd;
#ifdef MULTIPLE_CARD_SUPPORT
MC_RowID = pAd->MC_RowID;
#endif /* MULTIPLE_CARD_SUPPORT */
#ifdef HOSTAPD_SUPPORT
IoctlIF = pAd->IoctlIF;
#endif /* HOSTAPD_SUPPORT */
pDevNew = RtmpOSNetDevCreate((INT32)MC_RowID, (UINT32 *)&IoctlIF,
INT_MAIN, 0, sizeof(PRTMP_ADAPTER), INF_MAIN_DEV_NAME);
#ifdef HOSTAPD_SUPPORT
pAd->IoctlIF = IoctlIF;
#endif /* HOSTAPD_SUPPORT */
return pDevNew;
}