예제 #1
0
/*******************************************************************************
* Function Name  : DFU_Reset.
* Description    : DFU reset routine
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void DFU_Reset(void)
{
  /* Set DFU_DEVICE as not configured */
  Device_Info.Current_Configuration = 0;

  /* Current Feature initialization */
  pInformation->Current_Feature = DFU_ConfigDescriptor[7];

#ifdef STM32F10X_CL
  /* EP0 is already configured in DFU_Init by OTG_DEV_Init() function
      No Other endpoints needed for this firmware */
#else
  _SetBTABLE(BTABLE_ADDRESS);

  /* Initialize Endpoint 0 */
  _SetEPType(ENDP0, EP_CONTROL);
  _SetEPTxStatus(ENDP0, EP_TX_NAK);
  _SetEPRxAddr(ENDP0, ENDP0_RXADDR);
  SetEPRxCount(ENDP0, Device_Property.MaxPacketSize);
  _SetEPTxAddr(ENDP0, ENDP0_TXADDR);
  SetEPTxCount(ENDP0, Device_Property.MaxPacketSize);
  Clear_Status_Out(ENDP0);
  SetEPRxValid(ENDP0);

  /* Set this device to response on default address */
  SetDeviceAddress(0);
#endif /* STM32F10X_CL */

  /* Set the new control state of the device to Attached */
  bDeviceState = ATTACHED;
}
예제 #2
0
/*******************************************************************************
* Function Name  : DFU_Reset.
* Description    : DFU reset routine
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
void DFU_Reset(void)
{
  /* Set DFU_DEVICE as not configured */
  Device_Info.Current_Configuration = 0;

  /* Current Feature initialization */
  pInformation->Current_Feature = DFU_ConfigDescriptor[7];

  _SetBTABLE(BTABLE_ADDRESS);

  /* Initialize Endpoint 0 */
  _SetEPType(ENDP0, EP_CONTROL);
  _SetEPTxStatus(ENDP0, EP_TX_NAK);
  _SetEPRxAddr(ENDP0, ENDP0_RXADDR);
  SetEPRxCount(ENDP0, Device_Property.MaxPacketSize);
  _SetEPTxAddr(ENDP0, ENDP0_TXADDR);
  SetEPTxCount(ENDP0, Device_Property.MaxPacketSize);
  Clear_Status_Out(ENDP0);
  SetEPRxValid(ENDP0);

  /* Set this device to response on default address */
  SetDeviceAddress(0);

  /* Set the new control state of the device to Attached */
  bDeviceState = ATTACHED;
}
예제 #3
0
파일: usb_prop.c 프로젝트: mambrus/bitfire
/*******************************************************************************
* Function Name  : DFU_Reset
* Description    :
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
void DFU_Reset(void)
{
	/* Set DFU_DEVICE as not configured */
	Device_Info.Current_Configuration = 0;

	_SetBTABLE(BTABLE_ADDRESS);

	/* Initialize Endpoint 0 */
	_SetEPType(ENDP0, EP_CONTROL);
	_SetEPTxStatus(ENDP0, EP_TX_NAK);
	_SetEPRxAddr(ENDP0, ENDP0_RXADDR);
	SetEPRxCount(ENDP0, Device_Property.MaxPacketSize);
	_SetEPTxAddr(ENDP0, ENDP0_TXADDR);
	SetEPTxCount(ENDP0, Device_Property.MaxPacketSize);
	Clear_Status_Out(ENDP0);
	SetEPRxValid(ENDP0);
	
	/* Set this device to response on default address */
	SetDeviceAddress(0);

       /* if(!DFU_Button_Read())
	{
		DeviceState=STATE_dfuIDLE;
		DeviceStatus[4]=DeviceState;
		DeviceStatus[1]=0;
        	DeviceStatus[2]=0;
        	DeviceStatus[3]=0;
	}*/

} /* DFU_Reset() */
예제 #4
0
void usbReset(void) {
    pInformation->Current_Configuration = 0;

    /* current feature is current bmAttributes */
    pInformation->Current_Feature = (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELF_POWERED);

    _SetBTABLE(USB_BTABLE_ADDRESS);

    /* setup control endpoint 0 */
    _SetEPType(ENDP0, EP_CONTROL);
    _SetEPTxStatus(ENDP0, EP_TX_STALL);
    _SetEPRxAddr(ENDP0,VCOM_CTRL_RX_ADDR);
    _SetEPTxAddr(ENDP0,VCOM_CTRL_TX_ADDR);
    Clear_Status_Out(ENDP0);

    SetEPRxCount(ENDP0, pProperty->MaxPacketSize);
    SetEPRxValid(ENDP0);

    /* setup management endpoint 1  */
    SetEPType     (VCOM_NOTIFICATION_ENDP,     EP_INTERRUPT);
    SetEPTxAddr   (VCOM_NOTIFICATION_ENDP,     VCOM_NOTIFICATION_ADDR);
    SetEPTxStatus (VCOM_NOTIFICATION_ENDP,     EP_TX_NAK);
    SetEPRxStatus (VCOM_NOTIFICATION_ENDP,     EP_RX_DIS);

    /* setup data endpoint OUT (rx) */
    /*   SetEPType     (VCOM_RX_ENDP, EP_BULK); */
    /*   SetEPRxAddr   (VCOM_RX_ENDP, VCOM_RX_ADDR); */
    /*   SetEPRxCount  (VCOM_RX_ENDP, VCOM_RX_EPSIZE); */
    /*   // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS); */
    /*   SetEPRxStatus (VCOM_RX_ENDP, EP_RX_VALID); */

    SetEPType     (3, EP_BULK);
    SetEPRxAddr   (3, 0x110);
    SetEPRxCount  (3,64);
    // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS);
    SetEPRxStatus (3, EP_RX_VALID);

    /* setup data endpoint IN (tx)  */
    SetEPType     (VCOM_TX_ENDP, EP_BULK);
    SetEPTxAddr   (VCOM_TX_ENDP, VCOM_TX_ADDR);
    SetEPTxStatus (VCOM_TX_ENDP, EP_TX_NAK);
    SetEPRxStatus (VCOM_TX_ENDP, EP_RX_DIS);

    bDeviceState = ATTACHED;
    SetDeviceAddress(0);

    /* reset the rx fifo */
    recvBufIn   = 0;
    recvBufOut  = 0;
    maxNewBytes = VCOM_RX_EPSIZE;
    countTx     = 0;
}
예제 #5
0
void usbReset(void) {
  dfuUpdateByReset();

  pInformation->Current_Configuration = 0;
  pInformation->Current_Feature = usbConfigDescriptorDFU.Descriptor[7];

  _SetBTABLE(BTABLE_ADDRESS);

  /* setup the ctrl endpoint */
  _SetEPType(ENDP0, EP_CONTROL);
  _SetEPTxStatus(ENDP0, EP_TX_STALL);

  _SetEPRxAddr(ENDP0, ENDP0_RXADDR);
  _SetEPTxAddr(ENDP0, ENDP0_TXADDR);

  Clear_Status_Out(ENDP0);

  SetEPRxCount(ENDP0, pProperty->MaxPacketSize);
  //  SetEPTxCount(ENDP0, pProperty->MaxPacketSize);
  SetEPRxValid(ENDP0);

  bDeviceState = ATTACHED;
  SetDeviceAddress(0); /* different than usbSetDeviceAddr! comes from usb_core */
}