void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
if(htim_base->Instance==TIM6)
{
/* USER CODE BEGIN TIM6_MspInit 0 */
/* USER CODE END TIM6_MspInit 0 */
/* Peripheral clock enable */
__TIM6_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, 3, 0);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
/* USER CODE BEGIN TIM6_MspInit 1 */
/* USER CODE END TIM6_MspInit 1 */
}
else if(htim_base->Instance==TIM7)
{
/* USER CODE BEGIN TIM7_MspInit 0 */
/* USER CODE END TIM7_MspInit 0 */
/* Peripheral clock enable */
__TIM7_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM7_IRQn, 4, 0);
HAL_NVIC_EnableIRQ(TIM7_IRQn);
/* USER CODE BEGIN TIM7_MspInit 1 */
/* USER CODE END TIM7_MspInit 1 */
}
}
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
#ifdef USE_SCOPE
if(htim_base->Instance==TIM3)
{
/* USER CODE BEGIN TIM3_MspInit 0 */
/* USER CODE END TIM3_MspInit 0 */
/* Peripheral clock enable */
__TIM3_CLK_ENABLE();
/* USER CODE BEGIN TIM3_MspInit 1 */
/* USER CODE END TIM3_MspInit 1 */
}
#endif //USE_SCOPE
#ifdef USE_GEN
if(htim_base->Instance==TIM6){
__TIM6_CLK_ENABLE();
}
if(htim_base->Instance==TIM7){
__TIM7_CLK_ENABLE();
}
#endif //USE_GEN
}
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
GPIO_InitTypeDef GPIO_InitStruct;
if(htim_base->Instance==TIM3)
{
/* USER CODE BEGIN TIM3_MspInit 0 */
/* USER CODE END TIM3_MspInit 0 */
/* Peripheral clock enable */
__TIM3_CLK_ENABLE();
/**TIM3 GPIO Configuration
PA6 ------> TIM3_CH1
PA7 ------> TIM3_CH2
PB0 ------> TIM3_CH3
PB1 ------> TIM3_CH4
*/
GPIO_InitStruct.Pin = GPIO_PIN_6|GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/* USER CODE BEGIN TIM3_MspInit 1 */
/* USER CODE END TIM3_MspInit 1 */
}
else if(htim_base->Instance==TIM7)
{
/* USER CODE BEGIN TIM7_MspInit 0 */
/* USER CODE END TIM7_MspInit 0 */
/* Peripheral clock enable */
__TIM7_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM7_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM7_IRQn);
/* USER CODE BEGIN TIM7_MspInit 1 */
/* USER CODE END TIM7_MspInit 1 */
}
}
/* TIM7 init function - 1 usec timebase 16-bit */
void MX_TIM7_Init(void)
{
TIM_MasterConfigTypeDef sMasterConfig;
/* Peripheral clock enable */
__TIM7_CLK_ENABLE();
/* Peripheral configuration */
htim7.Instance = TIM7;
htim7.Init.Prescaler = 48;
htim7.Init.CounterMode = TIM_COUNTERMODE_DOWN;
htim7.Init.Period = 1;
HAL_TIM_Base_Init(&htim7);
sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
HAL_TIMEx_MasterConfigSynchronization(&htim7, &sMasterConfig);
}
//------------------------------------------------------------------------------------------------------------------------------------------------------
void Hardware_Init(void)
{
HAL_Init();
SystemClock_Config();
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
HAL_NVIC_SetPriority(SysTick_IRQn, PRIORITY_SYS_TICK);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, PRIORITY_TIMER_TIM6);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
Timer_Init();
Panel_Init();
FSMC_Init();
FSMC_SetMode(ModeFSMC_FPGA);
FDrive_Init();
}
void Hardware_Init()
{
HAL_Init();
SystemClock_Config();
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM6_CLK_ENABLE(); // Для отсчёта миллисекунд
__TIM2_CLK_ENABLE(); // Для тиков
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, 2, 0);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
if (HAL_TIM_Base_Init(&handleTIM6forTimer) != HAL_OK)
{
HARDWARE_ERROR
}
if (HAL_TIM_Base_Start_IT(&handleTIM6forTimer) != HAL_OK)
{
HARDWARE_ERROR
}
// Таймер для тиков
TIM_HandleTypeDef tim2handle =
{
TIM2,
{
0,
TIM_COUNTERMODE_UP,
0xffffffff,
TIM_CLOCKDIVISION_DIV1
}
};
if (HAL_TIM_Base_Init(&tim2handle) != HAL_OK)
{
HARDWARE_ERROR
}
if (HAL_TIM_Base_Start(&tim2handle) != HAL_OK)
{
HARDWARE_ERROR
}
Sound_Init();
#ifdef SPI_ENABLE
Panel_Init();
#endif
FSMC_Init();
ADC_Init();
FDrive_Init();
// Analog and DAC programmable SPI ////////////////////////////////////////
GPIO_InitTypeDef isGPIOG =
{
GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_5 | GPIO_PIN_7, // GPIO_PIN_1 - для работы с дисплеем
GPIO_MODE_OUTPUT_PP,
GPIO_NOPULL,
GPIO_SPEED_HIGH,
GPIO_AF0_MCO
};
HAL_GPIO_Init(GPIOG, &isGPIOG);
isGPIOG.Pin = GPIO_PIN_1;
isGPIOG.Mode = GPIO_MODE_OUTPUT_PP;
isGPIOG.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOG, &isGPIOG);
HAL_GPIO_WritePin(GPIOG, GPIO_PIN_1, GPIO_PIN_RESET); // PG1 - когда равен 1, чтение дисплея, в остальных случаях 0
RTC_Init();
}
//------------------------------------------------------------------------------------------------------------------------------------------------------
void Hardware_Init(void)
{
HAL_Init();
SystemClock_Config();
#ifndef _MS_VS
__GPIOA_CLK_ENABLE();
__GPIOB_CLK_ENABLE();
__GPIOC_CLK_ENABLE();
__GPIOD_CLK_ENABLE();
__GPIOE_CLK_ENABLE();
__GPIOF_CLK_ENABLE();
__GPIOG_CLK_ENABLE();
__DMA1_CLK_ENABLE(); // Для DAC1 (бикалка)
__TIM7_CLK_ENABLE(); // Для DAC1 (бикалка)
__DAC_CLK_ENABLE(); // Для бикалки
__PWR_CLK_ENABLE();
__SYSCFG_CLK_ENABLE();
#endif
HAL_NVIC_SetPriority(SysTick_IRQn, PRIORITY_SYS_TICK);
// Timer /////////////////////////////////////////////////////////////////
//RCC_PCLK1Config(RCC_HCLK_Div1);
// Таймер для мс
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, PRIORITY_TIMER_TIM6);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
Timer_Init();
Sound_Init();
Panel_Init();
FSMC_Init();
FSMC_SetMode(ModeFSMC_FPGA);
RAM_Init();
FDrive_Init();
// Analog and DAC programmable SPI ////////////////////////////////////////
GPIO_InitTypeDef isGPIO =
{
GPIO_PIN_10 | GPIO_PIN_12, // SPI SCLK, DATA
GPIO_MODE_OUTPUT_PP,
GPIO_NOPULL,
GPIO_SPEED_HIGH,
GPIO_AF0_MCO
};
HAL_GPIO_Init(GPIOC, &isGPIO);
isGPIO.Pin = GPIO_PIN_3 | GPIO_PIN_6; // SPI select1, select2
HAL_GPIO_Init(GPIOD, &isGPIO);
isGPIO.Pin = GPIO_PIN_10 | GPIO_PIN_15; // SPI select3, select4
HAL_GPIO_Init(GPIOG, &isGPIO);
RTC_Init();
}
void HAL_TIM_Base_MspInit(TIM_HandleTypeDef* htim_base)
{
if(htim_base->Instance==TIM1)
{
/* USER CODE BEGIN TIM1_MspInit 0 */
/* USER CODE END TIM1_MspInit 0 */
/* Peripheral clock enable */
__TIM1_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM1_BRK_TIM9_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM1_BRK_TIM9_IRQn);
HAL_NVIC_SetPriority(TIM1_UP_TIM10_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM1_UP_TIM10_IRQn);
HAL_NVIC_SetPriority(TIM1_CC_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM1_CC_IRQn);
/* USER CODE BEGIN TIM1_MspInit 1 */
/* USER CODE END TIM1_MspInit 1 */
}
else if(htim_base->Instance==TIM4)
{
/* USER CODE BEGIN TIM4_MspInit 0 */
/* USER CODE END TIM4_MspInit 0 */
/* Peripheral clock enable */
__TIM4_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM4_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM4_IRQn);
/* USER CODE BEGIN TIM4_MspInit 1 */
/* USER CODE END TIM4_MspInit 1 */
}
else if(htim_base->Instance==TIM6)
{
/* USER CODE BEGIN TIM6_MspInit 0 */
/* USER CODE END TIM6_MspInit 0 */
/* Peripheral clock enable */
__TIM6_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM6_DAC_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM6_DAC_IRQn);
/* USER CODE BEGIN TIM6_MspInit 1 */
/* USER CODE END TIM6_MspInit 1 */
}
else if(htim_base->Instance==TIM7)
{
/* USER CODE BEGIN TIM7_MspInit 0 */
/* USER CODE END TIM7_MspInit 0 */
/* Peripheral clock enable */
__TIM7_CLK_ENABLE();
/* USER CODE BEGIN TIM7_MspInit 1 */
/* USER CODE END TIM7_MspInit 1 */
}
else if(htim_base->Instance==TIM9)
{
/* USER CODE BEGIN TIM9_MspInit 0 */
/* USER CODE END TIM9_MspInit 0 */
/* Peripheral clock enable */
__TIM9_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM1_BRK_TIM9_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM1_BRK_TIM9_IRQn);
/* USER CODE BEGIN TIM9_MspInit 1 */
/* USER CODE END TIM9_MspInit 1 */
}
else if(htim_base->Instance==TIM10)
{
/* USER CODE BEGIN TIM10_MspInit 0 */
/* USER CODE END TIM10_MspInit 0 */
/* Peripheral clock enable */
__TIM10_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM1_UP_TIM10_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM1_UP_TIM10_IRQn);
/* USER CODE BEGIN TIM10_MspInit 1 */
/* USER CODE END TIM10_MspInit 1 */
}
else if(htim_base->Instance==TIM11)
{
/* USER CODE BEGIN TIM11_MspInit 0 */
/* USER CODE END TIM11_MspInit 0 */
/* Peripheral clock enable */
__TIM11_CLK_ENABLE();
/* USER CODE BEGIN TIM11_MspInit 1 */
/* USER CODE END TIM11_MspInit 1 */
}
else if(htim_base->Instance==TIM13)
{
/* USER CODE BEGIN TIM13_MspInit 0 */
/* USER CODE END TIM13_MspInit 0 */
/* Peripheral clock enable */
__TIM13_CLK_ENABLE();
/* Peripheral interrupt init*/
HAL_NVIC_SetPriority(TIM8_UP_TIM13_IRQn, 5, 0);
HAL_NVIC_EnableIRQ(TIM8_UP_TIM13_IRQn);
/* USER CODE BEGIN TIM13_MspInit 1 */
/* USER CODE END TIM13_MspInit 1 */
}
}
