예제 #1
0
파일: tlv320aic23b.c 프로젝트: Mazetti/asf
void aic23b_dac_start(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t arg),
                      uint32_t callback_opt,
                      uint32_t pba_hz)
{
#if AIC23B_CTRL_INTERFACE == AIC23B_CTRL_INTERFACE_SPI
  static const spi_options_t AIC23B_SPI_OPTIONS =
  {
    .reg          = AIC23B_SPI_NPCS,
    .baudrate     = AIC23B_SPI_MASTER_SPEED,
    .bits         = AIC23B_CTRL_SIZE,
    .spck_delay   = 0,
    .trans_delay  = 0,
    .stay_act     = 0,
    .spi_mode     = 3,
    .modfdis      = 1
  };
  spi_setupChipReg(AIC23B_SPI, &AIC23B_SPI_OPTIONS, pba_hz);
#endif

  aic23b_dac_stop();

  gpio_enable_module(AIC23B_SSC_DAC_GPIO_MAP,
                     sizeof(AIC23B_SSC_DAC_GPIO_MAP) / sizeof(AIC23B_SSC_DAC_GPIO_MAP[0]));

  aic23b_pdc_t pdc;
  pdc.data  = AIC23B_DEFAULT(AIC23B_PDC);
  pdc.off   = 0;
  pdc.clk   = 0;
  pdc.osc   = 0;
  pdc.out   = 0;
  pdc.dac   = 0;
  pdc.adc   = 1;
  pdc.mic   = 1;
  pdc.line  = 1;
  aic23b_set_power_down_state(pdc);

  aic23b_dac_setup(sample_rate_hz,
                   num_channels,
                   bits_per_sample,
                   swap_channels,
                   callback,
                   callback_opt,
                   pba_hz);

  aic23b_aapc_t aapc;
  aapc.data = AIC23B_DEFAULT(AIC23B_AAPC);
  aapc.ste  = 0;
  aapc.dac  = 1;
  aapc.byp  = 0;
  aapc.micm = 1;
  aapc.micb = 0;
  aic23b_set_analog_audio_path(aapc);

  aic23b_dapc_t dapc;
  dapc.data   = AIC23B_DEFAULT(AIC23B_DAPC);
  dapc.dacm   = 0;
  dapc.deemp  = AIC23B_DAPC_DEEMP_NONE;
  dapc.adchp  = 1;
  aic23b_set_digital_audio_path(dapc);

  // set an acceptable start volume
  aic23b_set_headphone_volume(AIC23B_LEFT_CHANNEL | AIC23B_RIGHT_CHANNEL,
                              -30,
                              true);

  aic23b_activate_dig_audio(true);

  INTC_register_interrupt(&aic23b_ssc_tx_pdca_int_handler,
                          AIC23B_SSC_TX_PDCA_IRQ,
                          AIC23B_SSC_TX_PDCA_INT_LEVEL);
}


void aic23b_dac_setup(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t arg),
                      uint32_t callback_opt,
                      uint32_t pba_hz)
{
#if defined(AIC23B_DAC_USE_RX_CLOCK) && AIC23B_DAC_USE_RX_CLOCK == true
  #if defined(AIC23B_DAC_RX_CLOCK_SET_CALLBACK)
    AIC23B_DAC_RX_CLOCK_SET_CALLBACK(2 * sample_rate_hz *
                                     ((bits_per_sample <= 16) ? 16 :
                                     (bits_per_sample <= 20) ? 20 :
                                     (bits_per_sample <= 24) ? 24 :
                                     32));
  #endif
  ssc_i2s_init(AIC23B_SSC,
               sample_rate_hz,
               bits_per_sample,
               (bits_per_sample <= 16) ? 16 :
               (bits_per_sample <= 20) ? 20 :
               (bits_per_sample <= 24) ? 24 :
                                         32,
               SSC_I2S_MODE_STEREO_OUT_EXT_CLK,
               pba_hz);
#else
  ssc_i2s_init(AIC23B_SSC,
               sample_rate_hz,
               bits_per_sample,
               (bits_per_sample <= 16) ? 16 :
               (bits_per_sample <= 20) ? 20 :
               (bits_per_sample <= 24) ? 24 :
                                         32,
               SSC_I2S_MODE_STEREO_OUT,
               pba_hz);
#endif

  pdca_channel_options_t aic23b_ssc_pdca_options =
  {
    .addr           = NULL,
    .size           = 0,
    .r_addr         = NULL,
    .r_size         = 0,
    .pid            = AIC23B_SSC_TX_PDCA_PID,
    .transfer_size  = (bits_per_sample <=  8) ? PDCA_TRANSFER_SIZE_BYTE      :
                      (bits_per_sample <= 16) ? PDCA_TRANSFER_SIZE_HALF_WORD :
                                                PDCA_TRANSFER_SIZE_WORD
  };
  pdca_init_channel(AIC23B_SSC_TX_PDCA_CHANNEL, &aic23b_ssc_pdca_options);
  pdca_enable(AIC23B_SSC_TX_PDCA_CHANNEL);

#if !defined(AIC23B_DAC_USE_RX_CLOCK) || AIC23B_DAC_USE_RX_CLOCK == false || \
    !defined(AIC23B_DAC_RX_CLOCK_SET_CALLBACK)
  // Set DAC frequency
  aic23b_configure_freq(AIC23B_MCLK_HZ, sample_rate_hz);
#endif

  aic23b_daif_t daif;
  daif.data   = AIC23B_DEFAULT(AIC23B_DAIF);
  daif.ms     = AIC23B_DAIF_MS_SLAVE;
  daif.lrswap = swap_channels;
  daif.lrp    = 0;
  daif.iwl    = (bits_per_sample <= 16) ? AIC23B_DAIF_IWL_16 :
                (bits_per_sample <= 20) ? AIC23B_DAIF_IWL_20 :
                (bits_per_sample <= 24) ? AIC23B_DAIF_IWL_24 :
                                          AIC23B_DAIF_IWL_32;
  daif.fmt    = AIC23B_DAIF_FMT_I2S;
  aic23b_write_reg(AIC23B_DAIF, daif.data);

  aic23b_output_params.num_channels             = num_channels;
  aic23b_output_params.callback                 = callback;
  aic23b_output_params.callback_opt             = callback_opt;
}
#endif

bool aic23b_dac_output(void *sample_buffer, size_t sample_length)
{
  bool global_interrupt_enabled;

  if (!(pdca_get_transfer_status(AIC23B_SSC_TX_PDCA_CHANNEL) &
        PDCA_TRANSFER_COUNTER_RELOAD_IS_ZERO))
    return false;

  if (sample_length)
  {
    if (aic23b_output_params.num_channels == 1)
    {
      int16_t *s16_sample_buffer = sample_buffer;
      int i;

      for (i = sample_length - 1; i >= 0; i--)
      {
        s16_sample_buffer[2 * i + 1] =
        s16_sample_buffer[2 * i]     = s16_sample_buffer[i];
      }
    }

    // The PDCA is not able to synchronize its start of transfer with the SSC
    // start of period, so this has to be done by polling the TF pin.
    // Not doing so may result in channels being swapped randomly.
    if ((global_interrupt_enabled = Is_global_interrupt_enabled()))
      Disable_global_interrupt();
    if (pdca_get_transfer_status(AIC23B_SSC_TX_PDCA_CHANNEL) &
        PDCA_TRANSFER_COMPLETE)
    {
      while (gpio_get_pin_value(AIC23B_SSC_TX_FRAME_SYNC_PIN));
      while (!gpio_get_pin_value(AIC23B_SSC_TX_FRAME_SYNC_PIN));
    }
    pdca_reload_channel(AIC23B_SSC_TX_PDCA_CHANNEL, sample_buffer, sample_length * 2);
    pdca_get_reload_size(AIC23B_SSC_TX_PDCA_CHANNEL);
    if (global_interrupt_enabled)
      Enable_global_interrupt();

    if (aic23b_output_params.callback_opt & AUDIO_DAC_OUT_OF_SAMPLE_CB)
      pdca_enable_interrupt_transfer_complete(AIC23B_SSC_TX_PDCA_CHANNEL);
    if (aic23b_output_params.callback_opt & AUDIO_DAC_RELOAD_CB)
      pdca_enable_interrupt_reload_counter_zero(AIC23B_SSC_TX_PDCA_CHANNEL);
  }
  return true;
}
예제 #2
0
파일: tlv320aic23b.c 프로젝트: Mazetti/asf
void aic23b_adc_start(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t arg),
                      uint32_t callback_opt,
                      uint32_t pba_hz)
{
#if AIC23B_CTRL_INTERFACE == AIC23B_CTRL_INTERFACE_SPI
  static const spi_options_t AIC23B_SPI_OPTIONS =
  {
    .reg          = AIC23B_SPI_NPCS,
    .baudrate     = AIC23B_SPI_MASTER_SPEED,
    .bits         = AIC23B_CTRL_SIZE,
    .spck_delay   = 0,
    .trans_delay  = 0,
    .stay_act     = 0,
    .spi_mode     = 3,
    .modfdis      = 1
  };
  spi_setupChipReg(AIC23B_SPI, &AIC23B_SPI_OPTIONS, pba_hz);
#endif

  aic23b_adc_stop();

  gpio_enable_module(AIC23B_SSC_ADC_GPIO_MAP,
                     sizeof(AIC23B_SSC_ADC_GPIO_MAP) / sizeof(AIC23B_SSC_ADC_GPIO_MAP[0]));

  aic23b_pdc_t pdc;
  pdc.data  = AIC23B_DEFAULT(AIC23B_PDC);
  pdc.off   = 0;
  pdc.clk   = 0;
  pdc.osc   = 0;
  pdc.out   = 0;
  pdc.dac   = 1;
  pdc.adc   = 0;
#if (AIC23B_INPUT==AIC23B_INPUT_LINE)
  pdc.mic   = 1;
  pdc.line  = 0;
#elif (AIC23B_INPUT==AIC23B_INPUT_MIC)
  pdc.mic   = 0;
  pdc.line  = 1;
#else
  #error No Input defined in file 'conf_tlv320aic23b.h'
#endif
  aic23b_set_power_down_state(pdc);

  aic23b_adc_setup(sample_rate_hz,
                   num_channels,
                   bits_per_sample,
                   swap_channels,
                   callback,
                   callback_opt,
                   pba_hz);

  aic23b_aapc_t aapc;
  aapc.data  = AIC23B_DEFAULT(AIC23B_AAPC);
#if (AIC23B_INPUT==AIC23B_INPUT_LINE)
  aapc.ste   = 0;
  aapc.dac   = 0;
  aapc.byp   = 0;
  aapc.insel = 0;
  aapc.micm  = 0;
  aapc.micb  = 0;
#elif (AIC23B_INPUT==AIC23B_INPUT_MIC)
  aapc.ste   = 0;
  aapc.dac   = 0;
  aapc.byp   = 0;
  aapc.insel = 1;
  aapc.micm  = 0;
  aapc.micb  = 0;
#else
  #error No Input defined in file 'conf_tlv320aic23b.h'
#endif
  aic23b_set_analog_audio_path(aapc);

  aic23b_dapc_t dapc;
  dapc.data   = AIC23B_DEFAULT(AIC23B_DAPC);
  dapc.dacm   = 0;
  dapc.deemp  = AIC23B_DAPC_DEEMP_NONE;
  dapc.adchp  = 0;
  aic23b_set_digital_audio_path(dapc);


  aic23b_llicvc_t llivc;
  llivc.data  = AIC23B_DEFAULT(AIC23B_LLICVC);
  llivc.liv   = 20;
  llivc.lim   = 0;
  llivc.lrs   = 1;
  aic23b_write_reg(AIC23B_LLICVC, llivc.data);

  aic23b_rlicvc_t rlivc;
  rlivc.data  = AIC23B_DEFAULT(AIC23B_RLICVC);
  rlivc.riv   = 20;
  rlivc.rim   = 0;
  rlivc.rls   = 1;
  aic23b_write_reg(AIC23B_RLICVC, rlivc.data);

  INTC_register_interrupt(&aic23b_ssc_rx_pdca_int_handler,
                          AIC23B_SSC_RX_PDCA_IRQ,
                          AIC23B_SSC_RX_PDCA_INT_LEVEL);

  aic23b_activate_dig_audio(true);

}

void aic23b_adc_setup(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t arg),
                      callback_opt,
                      uint32_t pba_hz)
{
  ssc_i2s_init(AIC23B_SSC,
               sample_rate_hz,
               bits_per_sample,
               (bits_per_sample <= 16) ? 16 :
               (bits_per_sample <= 20) ? 20 :
               (bits_per_sample <= 24) ? 24 :
                                         32,
               SSC_I2S_MODE_STEREO_IN,
               pba_hz);

  pdca_channel_options_t aic23b_ssc_pdca_options =
  {
    .addr           = NULL,
    .size           = 0,
    .r_addr         = NULL,
    .r_size         = 0,
    .pid            = AIC23B_SSC_RX_PDCA_PID,
    .transfer_size  = (bits_per_sample <=  8) ? PDCA_TRANSFER_SIZE_BYTE      :
                      (bits_per_sample <= 16) ? PDCA_TRANSFER_SIZE_HALF_WORD :
                                                PDCA_TRANSFER_SIZE_WORD
  };
  pdca_init_channel(AIC23B_SSC_RX_PDCA_CHANNEL, &aic23b_ssc_pdca_options);
  pdca_enable(AIC23B_SSC_RX_PDCA_CHANNEL);

  // Set ADC frequency
  aic23b_configure_freq(AIC23B_MCLK_HZ, sample_rate_hz);

  aic23b_daif_t daif;
  daif.data   = AIC23B_DEFAULT(AIC23B_DAIF);
  daif.ms     = AIC23B_DAIF_MS_SLAVE;
  daif.lrswap = swap_channels;
  daif.lrp    = 0;
  daif.iwl    = (bits_per_sample <= 16) ? AIC23B_DAIF_IWL_16 :
                (bits_per_sample <= 20) ? AIC23B_DAIF_IWL_20 :
                (bits_per_sample <= 24) ? AIC23B_DAIF_IWL_24 :
                                          AIC23B_DAIF_IWL_32;
  daif.fmt    = AIC23B_DAIF_FMT_I2S;
  aic23b_write_reg(AIC23B_DAIF, daif.data);

  aic23b_output_params.num_channels              = num_channels;
  aic23b_output_params.callback                  = callback;
  aic23b_output_params.callback_opt              = callback_opt;
}

void aic23b_adc_flush(void)
{
  pdca_disable_interrupt_transfer_complete(AIC23B_SSC_RX_PDCA_CHANNEL);

  while (!(pdca_get_transfer_status(AIC23B_SSC_RX_PDCA_CHANNEL) &
           PDCA_TRANSFER_COMPLETE));
}
예제 #3
0
void aic23b_codec_start(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t arg),
                      uint32_t callback_opt,
                      uint32_t pba_hz)
{
#if AIC23B_CTRL_INTERFACE == AIC23B_CTRL_INTERFACE_SPI
  static const spi_options_t AIC23B_SPI_OPTIONS =
  {
    .reg          = AIC23B_SPI_NPCS,
    .baudrate     = AIC23B_SPI_MASTER_SPEED,
    .bits         = AIC23B_CTRL_SIZE,
    .spck_delay   = 0,
    .trans_delay  = 0,
    .stay_act     = 0,
    .spi_mode     = 3,
    .modfdis      = 1
  };
  spi_setupChipReg(AIC23B_SPI, &AIC23B_SPI_OPTIONS, pba_hz);
#endif

  aic23b_codec_stop();

  gpio_enable_module(AIC23B_SSC_CODEC_GPIO_MAP,
                     sizeof(AIC23B_SSC_CODEC_GPIO_MAP) / sizeof(AIC23B_SSC_CODEC_GPIO_MAP[0]));

  aic23b_pdc_t pdc;
  pdc.data  = AIC23B_DEFAULT(AIC23B_PDC);
  pdc.off   = 0;
  pdc.clk   = 0;
  pdc.osc   = 0;
  pdc.out   = 0;
  pdc.dac   = 0;
  pdc.adc   = 0;
#if (AIC23B_INPUT==AIC23B_INPUT_LINE)
  pdc.mic   = 1;
  pdc.line  = 0;
#elif (AIC23B_INPUT==AIC23B_INPUT_MIC)
  pdc.mic   = 0;
  pdc.line  = 1;
#else
  #error No Input defined in file 'conf_tlv320aic23b.h'
#endif
  aic23b_set_power_down_state(pdc);

  aic23b_codec_setup(sample_rate_hz,
                   num_channels,
                   bits_per_sample,
                   swap_channels,
                   callback,
                   callback_opt,
                   pba_hz);

  aic23b_aapc_t aapc;
  aapc.data  = AIC23B_DEFAULT(AIC23B_AAPC);
#if (AIC23B_INPUT==AIC23B_INPUT_LINE)
  aapc.ste   = 0;
  aapc.dac   = 1;
  aapc.byp   = 0;
  aapc.insel = 0;
  aapc.micm  = 0;
  aapc.micb  = 1;
#elif (AIC23B_INPUT==AIC23B_INPUT_MIC)
  aapc.ste   = 0;
  aapc.dac   = 1;
  aapc.sta   = 4;
  aapc.byp   = 0;
  aapc.insel = 1;
  aapc.micm  = 0;
  aapc.micb  = 1;
#else
  #error No Input defined in file 'conf_tlv320aic23b.h'
#endif
  aic23b_set_analog_audio_path(aapc);

  aic23b_dapc_t dapc;
  dapc.data   = AIC23B_DEFAULT(AIC23B_DAPC);
  dapc.dacm   = 0;
  dapc.deemp  = AIC23B_DAPC_DEEMP_NONE;
  dapc.adchp  = 0;
  aic23b_set_digital_audio_path(dapc);


  aic23b_llicvc_t llivc;
  llivc.data  = AIC23B_DEFAULT(AIC23B_LLICVC);
  llivc.liv   = 20;
  llivc.lim   = 0;
  llivc.lrs   = 1;
  aic23b_write_reg(AIC23B_LLICVC, llivc.data);

  aic23b_rlicvc_t rlivc;
  rlivc.data  = AIC23B_DEFAULT(AIC23B_RLICVC);
  rlivc.riv   = 20;
  rlivc.rim   = 0;
  rlivc.rls   = 1;
  aic23b_write_reg(AIC23B_RLICVC, rlivc.data);

  INTC_register_interrupt(&aic23b_ssc_rx_pdca_int_handler,
                          AIC23B_SSC_RX_PDCA_IRQ,
                          AIC23B_SSC_RX_PDCA_INT_LEVEL);

  // set an acceptable start volume
  aic23b_set_headphone_volume(AIC23B_LEFT_CHANNEL | AIC23B_RIGHT_CHANNEL,
                              -30,
                              true);

  aic23b_activate_dig_audio(true);

  INTC_register_interrupt(&aic23b_ssc_tx_pdca_int_handler,
                          AIC23B_SSC_TX_PDCA_IRQ,
                          AIC23B_SSC_TX_PDCA_INT_LEVEL);
}

void aic23b_codec_setup(uint32_t sample_rate_hz,
                      uint8_t num_channels,
                      uint8_t bits_per_sample,
                      bool swap_channels,
                      void (*callback)(uint32_t opt),
                      uint32_t callback_opt,
                      uint32_t pba_hz)
{
  uint32_t master_clock = AIC23B_MCLK_HZ; // default configuration

  // Change the CPU frequency
  //
  //Disable_global_interrupt();

  // Switch to OSC0 during OSC1 transition
  //pm_switch_to_osc0(&AVR32_PM, FOSC0, OSC0_STARTUP);

  // Switch to PLL0 as the master clock
  //pm_switch_to_clock(&AVR32_PM, AVR32_PM_MCCTRL_MCSEL_PLL0);

  if (sample_rate_hz < (8000 + 8021) / 2)
  { // 8000 Hz
  }
  else if (sample_rate_hz < (8021 + 32000) / 2)
  { // 8021 Hz
  }
  else if (sample_rate_hz < (32000 + 44100) / 2)
  { // 32000 Hz
    master_clock = usb_stream_resync_frequency = 8192000;
    cs2200_freq_clk_out(_32_BITS_RATIO(usb_stream_resync_frequency, FOSC0));
    pba_hz = FCPU_HZ = FHSB_HZ = FPBA_HZ = FPBB_HZ = FMCK_HZ(8192000);
  }
  else if (sample_rate_hz < (44100 + 48000) / 2)
  { // 44100 Hz
    master_clock = usb_stream_resync_frequency = 11289600;
    cs2200_freq_clk_out(_32_BITS_RATIO(usb_stream_resync_frequency, FOSC0));
    pba_hz = FCPU_HZ = FHSB_HZ = FPBA_HZ = FPBB_HZ = FMCK_HZ(11289600);
  }
  else if (sample_rate_hz < (48000 + 88200) / 2)
  { // 48000 Hz
    master_clock = usb_stream_resync_frequency = 12288000;
    cs2200_freq_clk_out(_32_BITS_RATIO(usb_stream_resync_frequency, FOSC0));
    pba_hz = FCPU_HZ = FHSB_HZ = FPBA_HZ = FPBB_HZ = FMCK_HZ(12288000);
  }
  else if (sample_rate_hz < (88200 + 96000) / 2)
  { // 88200 Hz
  }
  else
  { // 96000 Hz
  }

  //Enable_global_interrupt();

  ssc_i2s_init(AIC23B_SSC,
               sample_rate_hz,
               bits_per_sample,
               (bits_per_sample <= 16) ? 16 :
               (bits_per_sample <= 20) ? 20 :
               (bits_per_sample <= 24) ? 24 :
                                         32,
               SSC_I2S_MODE_STEREO_OUT_STEREO_IN,
               pba_hz);

  pdca_channel_options_t aic23b_ssc_pdca_options_rx =
  {
    .addr           = NULL,
    .size           = 0,
    .r_addr         = NULL,
    .r_size         = 0,
    .pid            = AIC23B_SSC_RX_PDCA_PID,
    .transfer_size  = (bits_per_sample <=  8) ? PDCA_TRANSFER_SIZE_BYTE      :
                      (bits_per_sample <= 16) ? PDCA_TRANSFER_SIZE_HALF_WORD :
                                                PDCA_TRANSFER_SIZE_WORD

  };
  pdca_init_channel(AIC23B_SSC_RX_PDCA_CHANNEL, &aic23b_ssc_pdca_options_rx);
  pdca_enable(AIC23B_SSC_RX_PDCA_CHANNEL);

  pdca_channel_options_t aic23b_ssc_pdca_options_tx =
  {
    .addr           = NULL,
    .size           = 0,
    .r_addr         = NULL,
    .r_size         = 0,
    .pid            = AIC23B_SSC_TX_PDCA_PID,
    .transfer_size  = (bits_per_sample <=  8) ? PDCA_TRANSFER_SIZE_BYTE      :
                      (bits_per_sample <= 16) ? PDCA_TRANSFER_SIZE_HALF_WORD :
                                                PDCA_TRANSFER_SIZE_WORD
  };
  pdca_init_channel(AIC23B_SSC_TX_PDCA_CHANNEL, &aic23b_ssc_pdca_options_tx);
  pdca_enable(AIC23B_SSC_TX_PDCA_CHANNEL);

  // Set codec frequency
  aic23b_configure_freq(master_clock, sample_rate_hz);

  aic23b_daif_t daif;
  daif.data   = AIC23B_DEFAULT(AIC23B_DAIF);
  daif.ms     = AIC23B_DAIF_MS_SLAVE;
  daif.lrswap = swap_channels;
  daif.lrp    = 0;
  daif.iwl    = (bits_per_sample <= 16) ? AIC23B_DAIF_IWL_16 :
                (bits_per_sample <= 20) ? AIC23B_DAIF_IWL_20 :
                (bits_per_sample <= 24) ? AIC23B_DAIF_IWL_24 :
                                          AIC23B_DAIF_IWL_32;
  daif.fmt    = AIC23B_DAIF_FMT_I2S;
  aic23b_write_reg(AIC23B_DAIF, daif.data);

  aic23b_output_params.num_channels              = num_channels;
  aic23b_output_params.callback                  = callback;
  aic23b_output_params.callback_opt              = callback_opt;
}

void aic23b_codec_flush(void)
{
  pdca_disable_interrupt_transfer_complete(AIC23B_SSC_RX_PDCA_CHANNEL);
  while (!(pdca_get_transfer_status(AIC23B_SSC_RX_PDCA_CHANNEL) &
           PDCA_TRANSFER_COMPLETE));
  pdca_disable_interrupt_transfer_complete(AIC23B_SSC_TX_PDCA_CHANNEL);
  while (!(pdca_get_transfer_status(AIC23B_SSC_TX_PDCA_CHANNEL) &
           PDCA_TRANSFER_COMPLETE));
}

void aic23b_codec_stop(void)
{
  aic23b_codec_flush();

  aic23b_reset();

  aic23b_pdc_t pdc;
  pdc.data  = AIC23B_DEFAULT(AIC23B_PDC);
  pdc.off   = 1;
  pdc.clk   = 1;
  pdc.osc   = 1;
  pdc.out   = 1;
  pdc.dac   = 1;
  pdc.adc   = 1;
  pdc.mic   = 1;
  pdc.line  = 1;
  aic23b_set_power_down_state(pdc);

  pdca_disable(AIC23B_SSC_RX_PDCA_CHANNEL);
  pdca_disable(AIC23B_SSC_TX_PDCA_CHANNEL);

  ssc_i2s_reset(AIC23B_SSC);

  gpio_enable_gpio(AIC23B_SSC_CODEC_GPIO_MAP,
                   sizeof(AIC23B_SSC_CODEC_GPIO_MAP) / sizeof(AIC23B_SSC_CODEC_GPIO_MAP[0]));

  aic23b_output_params.num_channels             = 0;
  aic23b_output_params.callback                 = NULL;
  aic23b_output_params.callback_opt             = 0;
}