static void __init omap_apollon_init(void)
{
u32 v;
omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
omap_board_config = apollon_config;
omap_board_config_size = ARRAY_SIZE(apollon_config);
apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
/* REVISIT: where's the correct place */
omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
/* LCD PWR_EN */
omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
v |= (1 << 24);
omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
omap_serial_init();
}
static void __init omap_apollon_init(void)
{
u32 v;
omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
/* REVISIT: where's the correct place */
omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
/* LCD PWR_EN */
omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
v |= (1 << 24);
omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
apollon_smc91x_resources[1].start = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
apollon_smc91x_resources[1].end = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
omap_serial_init();
omap_sdrc_init(NULL, NULL);
omap_display_init(&apollon_dss_data);
}
static void __init omap_apollon_init(void)
{
u32 v;
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
/* REVISIT: where's the correct place */
omap_cfg_reg(W19_24XX_SYS_NIRQ);
/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
v |= (1 << 24);
omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
omap_board_config = apollon_config;
omap_board_config_size = ARRAY_SIZE(apollon_config);
omap_serial_init();
}
static void __init omap_apollon_init(void)
{
apollon_cs_init();
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
apollon_tsc_init();
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
omap_board_config = apollon_config;
omap_board_config_size = ARRAY_SIZE(apollon_config);
omap_serial_init();
omap_register_i2c_bus(1, 100, NULL, 0);
omap_register_i2c_bus(2, 100, NULL, 0);
spi_register_board_info(apollon_spi_board_info,
ARRAY_SIZE(apollon_spi_board_info));
apollon_mmc_init();
}