int board_init(void)
{
gd->bd->bi_arch_number=MACH_TYPE_MESON6_SKT;
gd->bd->bi_boot_params=BOOT_PARAMS_OFFSET;
#if CONFIG_JERRY_NAND_TEST //temp test
nand_init();
#endif
#ifdef CONFIG_AML_I2C
board_i2c_init();
#endif /*CONFIG_AML_I2C*/
#ifdef CONFIG_IR_REMOTE
board_ir_init();
#endif
#ifdef CONFIG_USB_DWC_OTG_HCD
board_usb_init(&g_usb_config_m6_skt_b,BOARD_USB_MODE_HOST);
board_usb_init(&g_usb_config_m6_skt_h,BOARD_USB_MODE_CHARGER);
#endif /*CONFIG_USB_DWC_OTG_HCD*/
key_init();
wifi_power_init();
run_command("magic_checkstatus", 0);
return 0;
}
int board_init(void)
{
#ifdef CONFIG_UART_A_FUNCTION_ADD
unsigned a_uart = (159375000/(115200*4) -1)
| UART_STP_BIT
| UART_PRTY_BIT
| UART_CHAR_LEN
| UART_CNTL_MASK_TX_EN
| UART_CNTL_MASK_RX_EN
| UART_CNTL_MASK_RST_TX
| UART_CNTL_MASK_RST_RX
| UART_CNTL_MASK_CLR_ERR ;
serial_init_uart_a(a_uart);
#endif
#if KSZ8091
CLEAR_CBUS_REG_MASK(PREG_PAD_GPIO1_EN_N, 1 << 31);
CLEAR_CBUS_REG_MASK(PREG_PAD_GPIO1_O, 1 << 31);
#endif
gd->bd->bi_arch_number=MACH_TYPE_MESON6_SKT;
gd->bd->bi_boot_params=BOOT_PARAMS_OFFSET;
#if CONFIG_JERRY_NAND_TEST //temp test
nand_init();
#endif
// LED
clrbits_le32(P_AO_GPIO_O_EN_N, (1 << 15));
clrbits_le32(P_AO_GPIO_O_EN_N, (1 << 31));
#ifdef CONFIG_AML_I2C
board_i2c_init();
#endif /*CONFIG_AML_I2C*/
#ifdef CONFIG_IR_REMOTE
board_ir_init();
#endif
#ifdef CONFIG_USB_DWC_OTG_HCD
board_usb_init(&g_usb_config_m6_skt_b,BOARD_USB_MODE_HOST);
board_usb_init(&g_usb_config_m6_skt_h,BOARD_USB_MODE_CHARGER);
#endif /*CONFIG_USB_DWC_OTG_HCD*/
#ifdef CONFIG_NET_WIFI
wifi_power_init();
#endif
key_init();
return 0;
}
int board_init(void)
{
#ifdef CONFIG_M201_COSTDOWN
/* pull up Linux rx/tx */
writel(readl(P_AO_RTI_PULL_UP_REG) | (3 << 0 | 3 << 16),
P_AO_RTI_PULL_UP_REG);
#endif
borad_power_init();
gd->bd->bi_arch_number=MACH_TYPE_MESON6_SKT;
gd->bd->bi_boot_params=BOOT_PARAMS_OFFSET;
#if CONFIG_JERRY_NAND_TEST //temp test
nand_init();
#endif
#ifdef CONFIG_AML_I2C
board_i2c_init();
#endif /*CONFIG_AML_I2C*/
#ifdef CONFIG_IR_REMOTE
board_ir_init();
#endif
#ifdef CONFIG_USB_DWC_OTG_HCD
board_usb_init(&g_usb_config_m6_skt_b,BOARD_USB_MODE_HOST);
board_usb_init(&g_usb_config_m6_skt_h,BOARD_USB_MODE_CHARGER);
#endif /*CONFIG_USB_DWC_OTG_HCD*/
#ifdef CONFIG_M201_COSTDOWN
/* 32k clock init */
printf("init 32k clock\n");
aml_set_reg32_mask(P_PERIPHS_PIN_MUX_9,0x1<<19);//set mode GPIOX_10-->CLK_OUT3
WRITE_CBUS_REG(PWM_PWM_E, 0x16d016d);
WRITE_CBUS_REG(PWM_MISC_REG_EF, 0x8001);
/* init led out put */
//red off
gpio_amlogic_requst(NULL, GPIOAO_2);
gpio_amlogic_direction_output(NULL, GPIOAO_2, 1);
//green on
gpio_amlogic_requst(NULL, GPIOAO_13);
gpio_amlogic_direction_output(NULL, GPIOAO_13, 0);
#endif
return 0;
}
int board_init(void)
{
gd->bd->bi_arch_number=MACH_TYPE_MESON6_SKT;
gd->bd->bi_boot_params=BOOT_PARAMS_OFFSET;
#ifdef CONFIG_UBOOT_BUILD_VERSION_INFO
print_build_version_info();
#endif
#if CONFIG_JERRY_NAND_TEST //temp test
nand_init();
#endif
#ifdef CONFIG_AML_I2C
board_i2c_init();
#endif /*CONFIG_AML_I2C*/
#ifdef CONFIG_IR_REMOTE
board_ir_init();
#endif
#ifdef CONFIG_USB_XHCI_AMLOGIC
board_usb_init(&g_usb_config_g9TV_skt,BOARD_USB_MODE_HOST);
#endif /*CONFIG_USB_XHCI_AMLOGIC*/
#if defined(CONFIG_VLSI_EMULATOR)
run_command("video dev open 1080p", 0);
#endif
#ifdef CONFIG_PWM_E_OUT_32K
printf("init pwm_e out 32k clock.\n");
writel(readl(P_PERIPHS_PIN_MUX_9) | (0x1 << 19), P_PERIPHS_PIN_MUX_9); //set mode GPIOX_10-->CLK_OUT3
writel(0x16d016d, P_PWM_PWM_E);
writel((readl(P_PWM_MISC_REG_EF) & ~(0xFF << 8)) | 0x8001, P_PWM_MISC_REG_EF);
#endif
//default power on 24M
writel(readl(P_PERIPHS_PIN_MUX_10)&~(1 << 11),P_PERIPHS_PIN_MUX_10);
writel(readl(P_AO_GPIO_O_EN_N)&~(1 << 18),P_AO_GPIO_O_EN_N);
writel(readl(P_AO_GPIO_O_EN_N)&~(1 << 2),P_AO_GPIO_O_EN_N);
return 0;
}