// public function, must be called by every task using serial_printf before calling it for the first time.
void cli_init()
{
if(!(cli_uart_initialized))
{
cli_uart_init(&cli_uart);
cli_stdout = (SerialDevice *)&cli_uart;
cli_uart_initialized = 1;
log_info("boot");
}
}
/**
* Starts the initialization, the tasks and then the scheduler.
*/
int main(void)
{
/* disable ETM at very first */
PINSEL10 &= ~((unsigned int)(1 << 3));
/* Initialize BMC hardware */
global_data.bmc_resetcause = 0x00;
/* IPMI message sequence counter */
global_data.seq_counter = 0x00;
/* site number used for entity instance */
global_data.bmc_siteno = 0x00;
/* reset sdr list */
sdr_list.sdr_count = 0;
/* init PLL */
init_clock();
/* init interrupts */
init_irq();
/* get reset cause */
init_resetcause();
/* init port pins */
init_portpins();
/* CUSTOM BOARD INIT CODE LOCATION 1 */
custom_init_1();
/* get HW and IPMB address */
custom_get_hw_ipmb_address();
uptime_init();
/* init RTC */
rtc_init();
/* create the FreeRTOS queues */
create_queues();
uart_init(UART_DEBUG_CONNECTOR, 115200);
uart_printf("Firmware started...\n");
/* init SPI/SSP controllers */
spi_init();
/* init SPI FLASH */
spi_flash_init_devices();
spi_flash_init(&spi_flash);
#ifdef CFG_MMC_I2C_MASTER
/* init BMC master I2C bus */
master_i2c_init(MASTER_BUS_I2C);
#endif
/* init EEPROM file system */
//spi_eeprom_init(&spi_eeprom);
#ifdef CFG_FS
if (fs_init(&efs, &spi_eeprom) != 0)
{
uart_printf("\nEEPROM not accesable!\n");
/* reboot bmc */
lpc_watchdog_start(CFG_BL_WATCHDOG_TIMEOUT, WD_RESET_MODE);
while (1);
}
#endif
/* init leds */
//led_init();
#ifndef CFG_ONCHIP_FLASH_GLOBAL_CONF
/* check EEPROM areas */
//eeprom_integrity_check_areas();
#endif
/* init CLI (and debug console) */
cli_uart_init(115200);
/* handle reset type warm/cold? */
//fru_handle_reset_type();
#ifdef CFG_CM
cm_fru_get_last_known_state();
#endif
#ifdef CFG_EXT_INT
/* init external interrupts */
external_interrupt_init();
#endif
#ifdef CFG_HELPER
/* init the helper task */
helper_init();
#endif
#ifdef CFG_BIOS_FLASH
/* init BIOS FLASH */
spi_flash_init(&bios_flash);
/* init FPGA BIOS flash selection */
bios_restore_active_flash_from_eeprom();
#endif
/* CUSTOM BOARD INIT CODE LOCATION 2 */
//custom_init_2();
/* get global configuration from EEPROM */
global_config();
/* CUSTOM BOARD INIT CODE LOCATION 3 */
//custom_init_3();
/* parse FRU */
fru_init(0);
#if defined (CFG_CM) || defined (CFG_MMC) || defined (CFG_IRTM) || defined(CFG_MCMC)
/* init the IPMB-L interface(s) */
ipmbl_init();
#endif
#ifdef CFG_LAN
/* read and set ncsi mac address from fru */
custom_set_ncsi_mac();
#endif
/* create message pool for IPMI messages */
message_pool_init();
/* init board task */
board_init();
/* init the BMC task */
bmc_init();
#ifdef CFG_PI_SERIAL_BASIC
/* init the payload interface */
pi_uart_b_init(CFG_PI_PORT_RATE);
#endif /* CFG_PI_SERIAL_BASIC */
#ifdef CFG_PI_SERIAL_TERMINAL
/* init the payload interface */
pi_uart_t_init(CFG_PI_PORT_RATE);
#endif /* CFG_PI_SERIAL_TERMINAL */
#ifdef CFG_PI_KCS
/* initialise kcs interface */
kcs_init();
#endif /* CFG_PI_KCS */
#ifdef CFG_ATCA
if (global_conf.operation_mode == OPERATION_MODE_STANDALONE)
{
/* configure IPMB-A and IPMB-B as master only in stanalone mode */
master_i2c_init(IPMB0A_I2C);
master_i2c_init(IPMB0B_I2C);
/* enable IPMB-0 pull ups and buffer */
ipmb0_bus_ctrl(IPMB0_A, IPMB_ENABLE);
ipmb0_bus_ctrl(IPMB0_B, IPMB_ENABLE);
}
else
{
/* init the IPMB-0 interface */
ipmb0_init();
}
#endif
#ifdef CFG_LAN_PLUS
sol_init();
#endif
#ifdef CFG_LAN
/* init ethernet hardware and Task */
eth_start();
#endif
/* init the SDR task */
/* PORT_NOTE: Needs to be started AFTER BMC task because of Semaphore dependency */
sdr_init();
/* parse all PICMG Records in FRU data and store relevant information */
//fru_parse_picmg();
/* init the IPMI message hub */
msg_hub_init();
/* init the event task */
event_init();
#ifdef CFG_CM
/* init the CM task */
init_cm();
#endif
#ifdef CFG_COOLING_MANAGER
cool_init();
#endif
/* do all post tests */
//post_test();
/* needs to be done after sdr initialization */
//hpm_check_bl_flags();
#ifdef CFG_BIOS_FLASH
/* collect BIOS/NVRAM version info (if payload power is off) */
if (!(signal_read(&sig_payload_power_enable)))
{
bios_redundancy_get_versions();
}
#endif
#ifdef CFG_WATCHDOG
/* start the FW watchdog */
lpc_watchdog_start(CFG_FW_WATCHDOG_TIMEOUT, WD_RESET_MODE);
#endif
/* set desired debug output mode before starting scheduler */
global_debug_uart_enabled = CFG_GLOBAL_DEBUG_UART;
/* all tasks have been initialized, start the scheduler */
vTaskStartScheduler();
/* Should never reach here! */
while (1);
}
