static int tegra20_boot_secondary(unsigned int cpu, struct task_struct *idle) { cpu = cpu_logical_map(cpu); /* * Force the CPU into reset. The CPU must remain in reset when * the flow controller state is cleared (which will cause the * flow controller to stop driving reset if the CPU has been * power-gated via the flow controller). This will have no * effect on first boot of the CPU since it should already be * in reset. */ tegra_put_cpu_in_reset(cpu); /* * Unhalt the CPU. If the flow controller was used to * power-gate the CPU this will cause the flow controller to * stop driving reset. The CPU will remain in reset because the * clock and reset block is now driving reset. */ flowctrl_write_cpu_halt(cpu, 0); tegra_enable_cpu_clock(cpu); flowctrl_write_cpu_csr(cpu, 0); /* Clear flow controller CSR. */ tegra_cpu_out_of_reset(cpu); return 0; }
static int tegra114_boot_secondary(unsigned int cpu, struct task_struct *idle) { int ret = 0; cpu = cpu_logical_map(cpu); if (cpumask_test_cpu(cpu, &tegra_cpu_init_mask)) { /* * Warm boot flow * The flow controller in charge of the power state and * control for each CPU. */ /* set SCLK as event trigger for flow controller */ flowctrl_write_cpu_csr(cpu, 1); flowctrl_write_cpu_halt(cpu, FLOW_CTRL_WAITEVENT | FLOW_CTRL_SCLK_RESUME); } else { /* * Cold boot flow * The CPU is powered up by toggling PMC directly. It will * also initial power state in flow controller. After that, * the CPU's power state is maintained by flow controller. */ ret = tegra_pmc_cpu_power_on(cpu); } return ret; }
void flowctrl_cpu_off(int cpu) { uint32_t reg; reg = cpu ? HALT_REG_CORE1 : HALT_REG_CORE0; flowctrl_prepare_cpu_off(cpu); flowctrl_write_cpu_halt(cpu, reg); }
void flowctrl_cpu_off(int cpu) { uint32_t val = FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG | FLOW_CTRL_CSR_ENABLE | (FLOW_CTRL_CSR_WFI_CPU0 << cpu); flowctrl_write_cpu_csr(cpu, val); flowctrl_write_cpu_halt(cpu, FLOW_CTRL_WAITEVENT); flowctrl_write_cc4_ctrl(cpu, 0); }
void flowctrl_cpu_suspend(int cpu) { uint32_t val; val = FLOW_CTRL_HALT_GIC_IRQ | FLOW_CTRL_HALT_GIC_FIQ | FLOW_CTRL_HALT_LIC_IRQ | FLOW_CTRL_HALT_LIC_FIQ | FLOW_CTRL_WAITEVENT; flowctrl_write_cpu_halt(cpu, val); val = FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG | FLOW_CTRL_CSR_ENABLE | (FLOW_CTRL_CSR_WFI_CPU0 << cpu); flowctrl_write_cpu_csr(cpu, val); }
static void tegra20_wake_cpu1_from_reset(void) { tegra_pen_lock(); tegra20_cpu_clear_resettable(); /* enable cpu clock on cpu */ tegra_enable_cpu_clock(1); /* take the CPU out of reset */ tegra_cpu_out_of_reset(1); /* unhalt the cpu */ flowctrl_write_cpu_halt(1, 0); tegra_pen_unlock(); }
int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle) { int status; /* * Force the CPU into reset. The CPU must remain in reset when the * flow controller state is cleared (which will cause the flow * controller to stop driving reset if the CPU has been power-gated * via the flow controller). This will have no effect on first boot * of the CPU since it should already be in reset. */ writel(CPU_RESET(cpu), CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET); dmb(); /* * Unhalt the CPU. If the flow controller was used to power-gate the * CPU this will cause the flow controller to stop driving reset. * The CPU will remain in reset because the clock and reset block * is now driving reset. */ flowctrl_write_cpu_halt(cpu, 0); switch (tegra_chip_id) { case TEGRA20: status = tegra20_power_up_cpu(cpu); break; case TEGRA30: status = tegra30_power_up_cpu(cpu); break; default: status = -EINVAL; break; } if (status) goto done; /* Take the CPU out of reset. */ writel(CPU_RESET(cpu), CLK_RST_CONTROLLER_RST_CPU_CMPLX_CLR); wmb(); done: return status; }
static int tegra30_boot_secondary(unsigned int cpu, struct task_struct *idle) { int ret; unsigned long timeout; cpu = cpu_logical_map(cpu); tegra_put_cpu_in_reset(cpu); flowctrl_write_cpu_halt(cpu, 0); /* * The power up sequence of cold boot CPU and warm boot CPU * was different. * * For warm boot CPU that was resumed from CPU hotplug, the * power will be resumed automatically after un-halting the * flow controller of the warm boot CPU. We need to wait for * the confirmaiton that the CPU is powered then removing * the IO clamps. * For cold boot CPU, do not wait. After the cold boot CPU be * booted, it will run to tegra_secondary_init() and set * tegra_cpu_init_mask which influences what tegra30_boot_secondary() * next time around. */ if (cpumask_test_cpu(cpu, &tegra_cpu_init_mask)) { timeout = jiffies + msecs_to_jiffies(50); do { if (tegra_pmc_cpu_is_powered(cpu)) goto remove_clamps; udelay(10); } while (time_before(jiffies, timeout)); } /* * The power status of the cold boot CPU is power gated as * default. To power up the cold boot CPU, the power should * be un-gated by un-toggling the power gate register * manually. */ if (!tegra_pmc_cpu_is_powered(cpu)) { ret = tegra_pmc_cpu_power_on(cpu); if (ret) return ret; /* Wait for the power to come up. */ timeout = jiffies + msecs_to_jiffies(100); while (!tegra_pmc_cpu_is_powered(cpu)) { if (time_after(jiffies, timeout)) return -ETIMEDOUT; udelay(10); } } remove_clamps: /* CPU partition is powered. Enable the CPU clock. */ tegra_enable_cpu_clock(cpu); udelay(10); /* Remove I/O clamps. */ ret = tegra_pmc_cpu_remove_clamping(cpu); if (ret) return ret; udelay(10); flowctrl_write_cpu_csr(cpu, 0); /* Clear flow controller CSR. */ tegra_cpu_out_of_reset(cpu); return 0; }
void flowctrl_cpu_on(int cpu) { flowctrl_write_cpu_csr(cpu, FLOW_CTRL_CSR_ENABLE); flowctrl_write_cpu_halt(cpu, FLOW_CTRL_WAITEVENT | FLOW_CTRL_HALT_SCLK); }