예제 #1
0
int main(void)
{
	DDRC |= (1 << DDRC7);
	PORTC |= (1 << PORTC7);
	_delay_ms(2);
	PORTC &= ~(1 << PORTC7);
	
 	init_power();
 	init_timeout_timer();
	init_switch();
	init_ref_clock();
	init_spi(2);
	init_buttons();
	init_serial(2400);
	init_adc();
	init_i2c();
	//Turn on interrupts
	sei();
	play_sounds();
	//Debug: Never Gets here
    while(1)
    {
		_delay_ms(1000);
		get_POT_set_TWIPOT();
	}
}
예제 #2
0
파일: main.c 프로젝트: sebseb7/pentabug
int main(void)
{

	/* hardware initialisation: */
	init_motor();
	init_buzzr();
	init_leds();
	init_switch();
	uint8_t mode = 0;

	for(;;) /* ever */  {
		//do something



		switch(mode){
			case 1: 
				mode_blinktest();
				break;
			case 2:
				mode_motortest();
				break;
			case 3: 
				mode_beeptest();
				break;
			default: //mode=0;
				blinkrattlebeep();

		}

		//check switches and change mode		
		switch( PIND & 0b00000011){
			case 0b00000010: //left switch pressed
				mode--;
				if (mode > 3) mode =3;
				flashleds(LED_L);
				break;
			case 0b00000001: //right switch pressed
				mode++;
				if (mode > 3) mode = 0;
				flashleds(LED_R);
				break;
			case 0b00000000: //both switches pressed
				flashleds(LED_R|LED_L);
				break;


		}

	}
	/* never  return 0; */
	return 0;
}
예제 #3
0
void init() 
{
	prc2 = 1;			/*PACRの書込み許可*/
	pacr = 3;			/*80ピンに設定*/
	
	/*クロック設定*/
	prc0=1;
	cm21=0;
	cm06=0;
	prc0=0;
	
	//
	init_led();
	//
	init_switch();
}
예제 #4
0
int main(int argc, char **argv) {

	// initialize gpio17 that is hooked up to the switch
	if(init_gpio()) {
		perror("could not initialize gpio17");
		return 1;
	}

	// S points to the switch values structure
	SWITCH_T * S = init_switch();

	while(1) {
		// read the switch values
		if(get_debounce_vals(S)) {
			perror("could not read values");
		}
		// print the state of the switch and light led accordingly
		switch_led(S);
	}

	return 0;
}
예제 #5
0
void init(void){

	DIR_DATA = STD_DIR_DATA;
	DIR_REGA = STD_DIR_REGA;
	DIR_REGB = STD_DIR_REGB;
	DIR_MC2  = STD_DIR_MC2;
	
	PORT_DATA = STD_PORT_DATA;
	PORT_REGA = STD_PORT_REGA;
	PORT_REGB = STD_PORT_REGB;
	PORT_MC2  = STD_PORT_MC2;
	
	init_mux();
	init_switch();
	init_buffer();
	init_processing();
	
	for(char i = 0; i<10; i++){
		for(char j = 0; j<13; j++){
			CUBE[i][j]=0x01;
		}
	}
   
    //Timer A:
    TCCR1A = 0x00;
    TCCR1B = (1<<WGM12)|(1<CS12);
	
    OCR1AH = TM1ZAEHLER>>8;
    OCR1AL = TM1ZAEHLER & 0x00FF;
	
	TIMSK = (1<<OCIE1A);
   
    sei();

	PORT_REGB |= (1<<PIN_ENABLE_CUBE); // CUBE EINSCHALTEN
	
}
예제 #6
0
// used for various testing
static int rctest_main(int argc, char *argv[])
{
	int on;

	if (argc < 3) {
		_dprintf("test what?\n");
	}
	else if (strcmp(argv[1], "rc_service")==0) {
		notify_rc(argv[2]);
	}
	else if(strcmp(argv[1], "get_phy_status")==0) {
		int mask;
		mask = atoi(argv[2]);
		TRACE_PT("debug for phy_status %x\n", get_phy_status(mask));
	}
	else if(strcmp(argv[1], "get_phy_speed")==0) {
		int mask;
		mask = atoi(argv[2]);
		TRACE_PT("debug for phy_speed %x\n", get_phy_speed(mask));
	}
	else if(strcmp(argv[1], "set_phy_ctrl")==0) {
		int mask, ctrl;
		mask = atoi(argv[2]);
		ctrl = atoi(argv[3]);
		TRACE_PT("debug for phy_speed %x\n", set_phy_ctrl(mask, ctrl));
	}
	else if(strcmp(argv[1], "handle_notifications")==0) {
		handle_notifications();
	}
	else if(strcmp(argv[1], "check_action")==0) {
		_dprintf("check: %d\n", check_action());
	}
	else if(strcmp(argv[1], "nvramhex")==0) {
		int i;
		char *nv;

		nv = nvram_safe_get(argv[2]);

		_dprintf("nvram %s(%d): ", nv, strlen(nv));
		for(i=0;i<strlen(nv);i++) {
			_dprintf(" %x", (unsigned char)*(nv+i));
		}
		_dprintf("\n");
	}
	else {
		on = atoi(argv[2]);
		_dprintf("%s %d\n", argv[1], on);

		if (strcmp(argv[1], "vlan") == 0)
		{	
			if(on) start_vlan();
			else stop_vlan();
		}
		else if (strcmp(argv[1], "lan") == 0) {
			if(on) start_lan();
			else stop_lan();
		}
		else if (strcmp(argv[1], "wl") == 0) {
			if(on) 
			{
				start_wl();
				lanaccess_wl();
			}
		}
		else if (strcmp(argv[1], "wan") == 0) {
			if(on) start_wan();
			else stop_wan();
		}
		else if (strcmp(argv[1], "firewall") == 0) {
			//if(on) start_firewall();
			//else stop_firewall();
		}
		else if (strcmp(argv[1], "watchdog") == 0) {
			if(on) start_watchdog();
			else stop_watchdog();
		}
#ifdef RTCONFIG_FANCTRL
		else if (strcmp(argv[1], "phy_tempsense") == 0) {
			if(on) start_phy_tempsense();
			else stop_phy_tempsense();
		}
#endif
#ifdef RTCONFIG_BCMWL6
#ifdef RTCONFIG_PROXYSTA
		else if (strcmp(argv[1], "psta_monitor") == 0) {
			if(on) start_psta_monitor();
			else stop_psta_monitor();
		}
#endif
#endif
		else if (strcmp(argv[1], "qos") == 0) {//qos test
			if(on){
#ifdef RTCONFIG_RALINK
				if (module_loaded("hw_nat"))
				{
					modprobe_r("hw_nat");
					sleep(1);
#if 0
					system("echo 0 > /proc/sys/net/ipv4/conf/default/force_igmp_version");
					system("echo 0 > /proc/sys/net/ipv4/conf/all/force_igmp_version");
#endif
				}
#endif
				add_iQosRules(get_wan_ifname(0));
				start_iQos();
			}
			else 
			{
#ifdef RTCONFIG_RALINK
				if (nvram_get_int("hwnat") &&
					/* TODO: consider RTCONFIG_DUALWAN case */
//					!nvram_match("wan0_proto", "l2tp") &&
//					!nvram_match("wan0_proto", "pptp") &&
//					!(nvram_get_int("fw_pt_l2tp") || nvram_get_int("fw_pt_ipsec") &&
//					(nvram_match("wl0_radio", "0") || nvram_get_int("wl0_mrate_x")) &&
//					(nvram_match("wl1_radio", "0") || nvram_get_int("wl1_mrate_x")) &&
					!module_loaded("hw_nat"))
				{
#if 0
					system("echo 2 > /proc/sys/net/ipv4/conf/default/force_igmp_version");
					system("echo 2 > /proc/sys/net/ipv4/conf/all/force_igmp_version");
#endif
					modprobe("hw_nat");
					sleep(1);
				}
#endif
				stop_iQos();
				del_iQosRules();
			}
		}
#ifdef RTCONFIG_WEBDAV
		else if (strcmp(argv[1], "webdav") == 0) {
			if(on)
				start_webdav();
		}
#endif
		else if (strcmp(argv[1], "gpiow") == 0) {
			if(argc>=4) set_gpio(atoi(argv[2]), atoi(argv[3]));
		}
		else if (strcmp(argv[1], "gpior") == 0) {
			_dprintf("%d\n", get_gpio(atoi(argv[2])));
		}
		else if (strcmp(argv[1], "gpiod") == 0) {
			if(argc>=4) gpio_dir(atoi(argv[2]), atoi(argv[3]));
		}
		else if (strcmp(argv[1], "init_switch") == 0) {
			init_switch(on);
		}
		else if (strcmp(argv[1], "set_action") == 0) {
			set_action(on);
		}
		else if (strcmp(argv[1], "pwr_usb") == 0) {
			set_pwr_usb(atoi(argv[2]));
			_dprintf("done.\n");
		}
		else {
			printf("what?\n");
		}
	}
	return 0;
}
예제 #7
0
파일: main.c 프로젝트: u1v3r/pds-switch
int main(int argc, char *argv[] ){

    init_switch();

    return 0;
}
예제 #8
0
파일: rc.c 프로젝트: hebjt/asuswrt-merlin
// used for various testing
static int rctest_main(int argc, char *argv[])
{
	int on;

	if (argc < 2) {
		_dprintf("test what?\n");
	}
	else if (strcmp(argv[1], "rc_service")==0) {
		notify_rc(argv[2]);
	}
	else if(strcmp(argv[1], "get_phy_status")==0) {
		int mask;
		mask = atoi(argv[2]);
		TRACE_PT("debug for phy_status %x\n", get_phy_status(mask));
	}
	else if(strcmp(argv[1], "get_phy_speed")==0) {
		int mask;
		mask = atoi(argv[2]);
		TRACE_PT("debug for phy_speed %x\n", get_phy_speed(mask));
	}
	else if(strcmp(argv[1], "set_phy_ctrl")==0) {
		int mask, ctrl;
		mask = atoi(argv[2]);
		ctrl = atoi(argv[3]);
		TRACE_PT("debug for phy_speed %x\n", set_phy_ctrl(mask, ctrl));
	}
	else if(strcmp(argv[1], "handle_notifications")==0) {
		handle_notifications();
	}
	else if(strcmp(argv[1], "check_action")==0) {
		_dprintf("check: %d\n", check_action());
	}
	else if(strcmp(argv[1], "nvramhex")==0) {
		int i;
		char *nv;

		nv = nvram_safe_get(argv[2]);

		_dprintf("nvram %s(%d): ", nv, strlen(nv));
		for(i=0;i<strlen(nv);i++) {
			_dprintf(" %x", (unsigned char)*(nv+i));
		}
		_dprintf("\n");
	}
	else {
		on = atoi(argv[2]);
		_dprintf("%s %d\n", argv[1], on);

		if (strcmp(argv[1], "vlan") == 0)
		{
			if(on) start_vlan();
			else stop_vlan();
		}
		else if (strcmp(argv[1], "lan") == 0) {
			if(on) start_lan();
			else stop_lan();
		}
		else if (strcmp(argv[1], "wl") == 0) {
			if(on)
			{
				start_wl();
				lanaccess_wl();
			}
		}
		else if (strcmp(argv[1], "wan") == 0) {
			if(on) start_wan();
			else stop_wan();
		}
		else if (strcmp(argv[1], "wan_port") == 0) {
			if(on) start_wan_port();
			else stop_wan_port();
		}
		else if (strcmp(argv[1], "firewall") == 0) {
			//if(on) start_firewall();
			//else stop_firewall();
		}
		else if (strcmp(argv[1], "watchdog") == 0) {
			if(on) start_watchdog();
			else stop_watchdog();
		}
#if ! (defined(RTCONFIG_QCA) || defined(RTCONFIG_RALINK))
		else if (strcmp(argv[1], "watchdog02") == 0) {
			if(on) start_watchdog02();
			else stop_watchdog02();
		}
#endif  /* ! (RTCONFIG_QCA || RTCONFIG_RALINK) */
		else if (strcmp(argv[1], "sw_devled") == 0) {
			if(on) start_sw_devled();
			else stop_sw_devled();
		}
#ifdef RTCONFIG_FANCTRL
		else if (strcmp(argv[1], "phy_tempsense") == 0) {
			if(on) start_phy_tempsense();
			else stop_phy_tempsense();
		}
#endif
#ifdef RTCONFIG_BCMWL6
#ifdef RTCONFIG_PROXYSTA
		else if (strcmp(argv[1], "psta_monitor") == 0) {
			if(on) start_psta_monitor();
			else stop_psta_monitor();
		}
#endif
#endif
#ifdef RTCONFIG_IPERF
		else if (strcmp(argv[1], "monitor") == 0) {
			if(on) start_monitor();
			else stop_monitor();
		}
#endif
		else if (strcmp(argv[1], "qos") == 0) {//qos test
			if(on){
#ifdef RTCONFIG_RALINK
				if (module_loaded("hw_nat"))
				{
					modprobe_r("hw_nat");
					sleep(1);
#if 0
					f_write_string("/proc/sys/net/ipv4/conf/default/force_igmp_version", "0", 0, 0);
					f_write_string("/proc/sys/net/ipv4/conf/all/force_igmp_version", "0", 0, 0);
#endif
				}
#endif
			add_iQosRules(get_wan_ifname(wan_primary_ifunit()));
#ifdef RTCONFIG_BWDPI
				if(nvram_get_int("qos_type") == 1) {
					start_dpi_engine_service();
					// force to rebuild firewall to avoid some loopback issue
					if (nvram_match("fw_nat_loopback", "2"))
						start_firewall(wan_primary_ifunit(), 0);
				}
				else
#endif
				start_iQos();
			}
			else
			{
#ifdef RTCONFIG_RALINK
				if (nvram_get_int("hwnat") &&
					/* TODO: consider RTCONFIG_DUALWAN case */
//					!nvram_match("wan0_proto", "l2tp") &&
//					!nvram_match("wan0_proto", "pptp") &&
//					!(nvram_get_int("fw_pt_l2tp") || nvram_get_int("fw_pt_ipsec") &&
//					(nvram_match("wl0_radio", "0") || nvram_get_int("wl0_mrate_x")) &&
//					(nvram_match("wl1_radio", "0") || nvram_get_int("wl1_mrate_x")) &&
					!module_loaded("hw_nat"))
				{
#if 0
					f_write_string("/proc/sys/net/ipv4/conf/default/force_igmp_version", "2", 0, 0);
					f_write_string("/proc/sys/net/ipv4/conf/all/force_igmp_version", "2", 0, 0);
#endif

#if defined(RTN14U) || defined(RTAC52U) || defined(RTAC51U) || defined(RTN11P) || defined(RTN300) || defined(RTN54U) || defined(RTAC1200HP) || defined(RTN56UB1) || defined(RTAC54U) || defined(RTN56UB2)
					if (!(!nvram_match("switch_wantag", "none")&&!nvram_match("switch_wantag", "")))
#endif
					{
						modprobe("hw_nat");
						sleep(1);
					}
				}
#endif
#ifdef RTCONFIG_BWDPI
				if(nvram_get_int("qos_type") == 1){
					stop_dpi_engine_service(1);
				}
				else
#endif
				stop_iQos();
				del_iQosRules();
			}
		}
#ifdef RTCONFIG_WEBDAV
		else if (strcmp(argv[1], "webdav") == 0) {
			if(on)
				start_webdav();
		}
#endif
#ifdef RTCONFIG_TUNNEL
		else if (strcmp(argv[1], "mastiff") == 0) {
			if(on)
				start_mastiff();
		}
#endif
		else if (strcmp(argv[1], "gpiow") == 0) {
			if(argc>=4) set_gpio(atoi(argv[2]), atoi(argv[3]));
		}
		else if (strcmp(argv[1], "gpior") == 0) {
			printf("%d\n", get_gpio(atoi(argv[2])));
		}
		else if (strcmp(argv[1], "gpiod") == 0) {
			if(argc>=4) gpio_dir(atoi(argv[2]), atoi(argv[3]));
		}
		else if (strcmp(argv[1], "init_switch") == 0) {
			init_switch();
		}
		else if (strcmp(argv[1], "set_action") == 0) {
			set_action(on);
		}
		else if (strcmp(argv[1], "pwr_usb") == 0) {
			set_pwr_usb(atoi(argv[2]));
			_dprintf("done.\n");
		}
		else if (strcmp(argv[1], "enc_chk") == 0) {
        		unsigned char enc_buf[ENC_WORDS_LEN];
        		unsigned char dec_buf[DATA_WORDS_LEN + 1];

			_dprintf("get enc str:[%s]\n", enc_str(argv[2], (char *) enc_buf));
			_dprintf("get dec str:[%s]\n", dec_str((char *) enc_buf, (char *) dec_buf));

			_dprintf("done(%d)\n", strcmp(argv[2], (const char *) dec_buf));
		}
#ifdef RTCONFIG_BCMFA
		else if (strcmp(argv[1], "fa_rev") == 0) {
			_dprintf("(%d) done.\n", get_fa_rev());
		}
		else if (strcmp(argv[1], "fa_dump") == 0) {
			_dprintf("(%d) done.\n", get_fa_dump());
		}
#endif
		else {
			printf("what?\n");
		}
	}
	return 0;
}
예제 #9
0
void init_motor(void){
	init_switch();
	init_motorPWM();
}
예제 #10
0
파일: mashing.c 프로젝트: za6o/MyProject
void init_buttons(){
	init_switch();
	init_led();
	init_heater();
}