void v7_outer_cache_enable(void)
{
struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
unsigned int val;
/*
* Must disable the L2 before changing the latency parameters
* and auxiliary control register.
*/
clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
/*
* Set bit 22 in the auxiliary control register. If this bit
* is cleared, PL310 treats Normal Shared Non-cacheable
* accesses as Cacheable no-allocate.
*/
setbits_le32(&pl310->pl310_aux_ctrl, L310_SHARED_ATT_OVERRIDE_ENABLE);
if (is_mx6sl() || is_mx6sll()) {
val = readl(&iomux->gpr[11]);
if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
/* L2 cache configured as OCRAM, reset it */
val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
writel(val, &iomux->gpr[11]);
}
}
writel(0x132, &pl310->pl310_tag_latency_ctrl);
writel(0x132, &pl310->pl310_data_latency_ctrl);
val = readl(&pl310->pl310_prefetch_ctrl);
/* Turn on the L2 I/D prefetch */
val |= 0x30000000;
/*
* The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
* The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
* But according to ARM PL310 errata: 752271
* ID: 752271: Double linefill feature can cause data corruption
* Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
* Workaround: The only workaround to this erratum is to disable the
* double linefill feature. This is the default behavior.
*/
#ifndef CONFIG_MX6Q
val |= 0x40800000;
#endif
writel(val, &pl310->pl310_prefetch_ctrl);
val = readl(&pl310->pl310_power_ctrl);
val |= L2X0_DYNAMIC_CLK_GATING_EN;
val |= L2X0_STNDBY_MODE_EN;
writel(val, &pl310->pl310_power_ctrl);
setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
}
static inline int gpt_has_clk_source_osc(void)
{
#if defined(CONFIG_MX6)
if (((is_mx6dq()) && (soc_rev() > CHIP_REV_1_0)) ||
is_mx6dqp() || is_mx6sdl() || is_mx6sx() || is_mx6ul() ||
is_mx6ull() || is_mx6sll())
return 1;
return 0;
#else
return 0;
#endif
}
/* i2c_num can be from 0 - 3 */
int enable_i2c_clk(unsigned char enable, unsigned i2c_num)
{
u32 reg;
u32 mask;
u32 *addr;
if (i2c_num > 3)
return -EINVAL;
if (i2c_num < 3) {
mask = MXC_CCM_CCGR_CG_MASK
<< (MXC_CCM_CCGR2_I2C1_SERIAL_OFFSET
+ (i2c_num << 1));
reg = __raw_readl(&imx_ccm->CCGR2);
if (enable)
reg |= mask;
else
reg &= ~mask;
__raw_writel(reg, &imx_ccm->CCGR2);
} else {
if (is_mx6sll())
return -EINVAL;
if (is_mx6sx() || is_mx6ul() || is_mx6ull()) {
mask = MXC_CCM_CCGR6_I2C4_MASK;
addr = &imx_ccm->CCGR6;
} else {
mask = MXC_CCM_CCGR1_I2C4_SERIAL_MASK;
addr = &imx_ccm->CCGR1;
}
reg = __raw_readl(addr);
if (enable)
reg |= mask;
else
reg &= ~mask;
__raw_writel(reg, addr);
}
return 0;
}
