// Configure the CN interrupt handler
void __ISR(_CHANGE_NOTICE_VECTOR, ipl2) ChangeNotice_Handler(void)
{
unsigned int temp;
// clear the mismatch condition
temp = mPORTBRead();
// clear the interrupt flag
mCNClearIntFlag();
// .. things to do ..
if ( !(temp & (1<<2)) ) { //button on RB2 is pressed
if (MotorsON == 0)
MotorsON = 1;
else
MotorsON = 0;
}
if ( temp & (1<<3) ) {
M1forward = 1;
} else if ( !(temp & (1<<3)) ) {
M1forward = 0;
}
if ( temp & (1<<4) ) {
M2forward = 1;
} else if ( !(temp & (1<<4)) ) {
M2forward = 0;
}
}
void readCNAndClrIsr()
{
int portStatus = 0;
portStatus = mPORTDRead(); //clear mismatch
portStatus = mPORTBRead(); //clear mismatch
mCNClearIntFlag();
}
int main(void)
{
unsigned int temp;
// Configure the device for maximum performance but do not change the PBDIV
// Given the options, this function will change the flash wait states, RAM
// wait state and enable prefetch cache but will not change the PBDIV.
// The PBDIV value is already set via the pragma FPBDIV option above..
SYSTEMConfig(GetSystemClock(), SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
/*PORT CONFIGURATION for UART*/
// Blinky LED for Uart activity
//mPORTAClearBits(BIT_7);
//mPORTASetPinsDigitalOut(BIT_7);
// PINS used for the buttons
PORTSetPinsDigitalIn(IOPORT_B, BIT_2 | BIT_3 | BIT_4);
#define CONFIG (CN_ON | CN_IDLE_CON)
#define INTERRUPT (CHANGE_INT_ON | CHANGE_INT_PRI_2)
mCNOpen(CONFIG, CN4_ENABLE | CN5_ENABLE | CN6_ENABLE,
CN4_PULLUP_ENABLE | CN5_PULLUP_ENABLE | CN6_PULLUP_ENABLE);
temp = mPORTBRead();
//Analog input
CloseADC10();
#define PARAM1 ADC_MODULE_ON | ADC_FORMAT_INTG32 | ADC_CLK_AUTO | ADC_AUTO_SAMPLING_ON
#define PARAM2 ADC_VREF_AVDD_AVSS | ADC_SCAN_ON | ADC_SAMPLES_PER_INT_2 | ADC_BUF_16 | ADC_ALT_INPUT_OFF
#define PARAM3 ADC_CONV_CLK_INTERNAL_RC | ADC_SAMPLE_TIME_5
#define PARAM4 ENABLE_AN0_ANA | ENABLE_AN1_ANA
#define PARAM5 SKIP_SCAN_AN2 | SKIP_SCAN_AN3 | SKIP_SCAN_AN4 | SKIP_SCAN_AN5 | SKIP_SCAN_AN6 | SKIP_SCAN_AN7 | SKIP_SCAN_AN8 | SKIP_SCAN_AN9 | SKIP_SCAN_AN10 | SKIP_SCAN_AN11 | SKIP_SCAN_AN12 | SKIP_SCAN_AN13 | SKIP_SCAN_AN14 | SKIP_SCAN_AN15
SetChanADC10( ADC_CH0_NEG_SAMPLEA_NVREF | ADC_CH0_POS_SAMPLEA_AN0);
OpenADC10( PARAM1, PARAM2, PARAM3, PARAM4, PARAM5 );
EnableADC10();
//PORT D for motors
mPORTDClearBits(BIT_0 | BIT_1 | BIT_2 | BIT_3 |
BIT_4 | BIT_5 | BIT_6 | BIT_7 |
BIT_8 | BIT_9 | BIT_10 | BIT_11 |
BIT_12 | BIT_13 | BIT_14 | BIT_15); // Turn off PORTD on startup.
mPORTDSetPinsDigitalOut(BIT_0 | BIT_1 | BIT_2 | BIT_3 |
BIT_4 | BIT_5 | BIT_6 | BIT_7 |
BIT_8 | BIT_9 | BIT_10 | BIT_11 |
BIT_12 | BIT_13 | BIT_14 | BIT_15); // Make PORTD output.
// Explorer-16 uses UART2 to connect to the PC.
// This initialization assumes 36MHz Fpb clock. If it changes,
// you will have to modify baud rate initializer.
UARTConfigure(UART2, UART_ENABLE_PINS_TX_RX_ONLY);
UARTSetFifoMode(UART2, UART_INTERRUPT_ON_TX_NOT_FULL | UART_INTERRUPT_ON_RX_NOT_EMPTY);
UARTSetLineControl(UART2, UART_DATA_SIZE_8_BITS | UART_PARITY_NONE | UART_STOP_BITS_1);
UARTSetDataRate(UART2, GetPeripheralClock(), DESIRED_BAUDRATE);
UARTEnable(UART2, UART_ENABLE_FLAGS(UART_PERIPHERAL | UART_RX | UART_TX));
// Configure UART2 RX Interrupt
INTEnable(INT_SOURCE_UART_RX(UART2), INT_ENABLED);
INTSetVectorPriority(INT_VECTOR_UART(UART2), INT_PRIORITY_LEVEL_2);
INTSetVectorSubPriority(INT_VECTOR_UART(UART2), INT_SUB_PRIORITY_LEVEL_0);
// Congifure Change/Notice Interrupt Flag
ConfigIntCN(INTERRUPT);
// configure for multi-vectored mode
INTConfigureSystem(INT_SYSTEM_CONFIG_MULT_VECTOR);
// enable interrupts
INTEnableInterrupts();
WriteString("*** UART Interrupt-driven Example ***\r\n");
unsigned int channel1, channel2;
unsigned int motor1Time, motor2Time;
// Let interrupt handler do the work
while (1) {
while ( ! mAD1GetIntFlag() );
channel1 = ReadADC10(0);
channel2 = ReadADC10(1);
motor1Time = (channel1*(60000)/(1023) + 80000);
motor2Time = (channel2*(60000)/(1023) + 80000);
//maximo valor de motorTime = 140000
//use motor time for stepping delay
if (MotorsON) {
if (M1forward) {
adelante(1, motor1Time, 1);
} else {
atras(1, motor1Time, 1);
}
if (M2forward) {
adelante(1, motor2Time, 3);
} else {
atras(1, motor2Time, 3);
}
}
mAD1ClearIntFlag();
}
return 0;
}