void __init msm_8974_init_gpiomux(void)
{
int rc;
rc = msm_gpiomux_init_dt();
if (rc) {
pr_err("%s failed %d\n", __func__, rc);
return;
}
#if defined(CONFIG_KS8851) || defined(CONFIG_KS8851_MODULE)
msm_gpiomux_install(msm_eth_configs, ARRAY_SIZE(msm_eth_configs));
#endif
msm_gpiomux_install(msm_blsp_configs, ARRAY_SIZE(msm_blsp_configs));
msm_gpiomux_install(msm_blsp2_uart7_configs,
ARRAY_SIZE(msm_blsp2_uart7_configs));
msm_gpiomux_install(wcnss_5wire_interface,
ARRAY_SIZE(wcnss_5wire_interface));
msm_gpiomux_install(msm8974_slimbus_config,
ARRAY_SIZE(msm8974_slimbus_config));
msm_gpiomux_install(msm_touch_configs, ARRAY_SIZE(msm_touch_configs));
msm_gpiomux_install(hap_lvl_shft_config,
ARRAY_SIZE(hap_lvl_shft_config));
msm_gpiomux_install(msm_sensor_configs, ARRAY_SIZE(msm_sensor_configs));
msm_gpiomux_install(&sd_card_det, 1);
msm_gpiomux_sdc3_install();
msm_gpiomux_sdc4_install();
msm_gpiomux_install(msm_taiko_config, ARRAY_SIZE(msm_taiko_config));
msm_gpiomux_install(msm_hsic_configs, ARRAY_SIZE(msm_hsic_configs));
msm_gpiomux_install(msm_hsic_hub_configs,
ARRAY_SIZE(msm_hsic_hub_configs));
msm_gpiomux_install(msm_hdmi_configs, ARRAY_SIZE(msm_hdmi_configs));
if (machine_is_msm8974_fluid())
msm_gpiomux_install(msm_mhl_configs,
ARRAY_SIZE(msm_mhl_configs));
msm_gpiomux_install(msm8974_pri_auxpcm_configs,
ARRAY_SIZE(msm8974_pri_auxpcm_configs));
if (machine_is_msm8974_rumi())
msm_gpiomux_install(msm_rumi_blsp_configs,
ARRAY_SIZE(msm_rumi_blsp_configs));
}
int __cpuinit msm8974_boot_secondary(unsigned int cpu, struct task_struct *idle)
{
pr_debug("Starting secondary CPU %d\n", cpu);
if (per_cpu(cold_boot_done, cpu) == false) {
if (machine_is_msm8974_sim() || machine_is_mpq8092_sim())
release_secondary_sim(0xf9088000, cpu);
else if (!machine_is_msm8974_rumi())
msm8974_release_secondary(0xf9088000, cpu);
per_cpu(cold_boot_done, cpu) = true;
}
return release_from_pen(cpu);
}
/*
* Used to satisfy dependencies for devices that need to be
* run early or in a particular order. Most likely your device doesn't fall
* into this category, and thus the driver should not be added here. The
* EPROBE_DEFER can satisfy most dependency problems.
*/
void __init msm_8974_add_drivers(void)
{
msm_init_modem_notifier_list();
msm_smd_init();
msm_rpm_driver_init();
msm_lpmrs_module_init();
rpm_regulator_smd_driver_init();
msm_spm_device_init();
regulator_stub_init();
if (machine_is_msm8974_rumi())
msm_clock_init(&msm_dummy_clock_init_data);
else
msm_clock_init(&msm8974_clock_init_data);
msm8974_init_buses();
}
/*
* Used to satisfy dependencies for devices that need to be
* run early or in a particular order. Most likely your device doesn't fall
* into this category, and thus the driver should not be added here. The
* EPROBE_DEFER can satisfy most dependency problems.
*/
void __init msm8974_add_drivers(void)
{
msm_init_modem_notifier_list();
msm_smd_init();
msm_rpm_driver_init();
msm_lpmrs_module_init();
rpm_regulator_smd_driver_init();
msm_spm_device_init();
krait_power_init();
if (machine_is_msm8974_rumi())
msm_clock_init(&msm8974_rumi_clock_init_data);
else
msm_clock_init(&msm8974_clock_init_data);
msm8974_init_buses();
msm_thermal_device_init();
mxt_init_vkeys_8974();
}
