static void __init kurobox_pro_init(void)
{
orion5x_init();
orion5x_mpp_conf(kurobox_pro_mpp_modes);
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&kurobox_pro_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&kurobox_pro_sata_data);
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
KUROBOX_PRO_NOR_BOOT_SIZE);
platform_device_register(&kurobox_pro_nor_flash);
if (machine_is_kurobox_pro()) {
orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
KUROBOX_PRO_NAND_SIZE);
platform_device_register(&kurobox_pro_nand_flash);
}
i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
pm_power_off = kurobox_pro_power_off;
}
static void __init wrt350n_v2_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(wrt350n_v2_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data);
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
WRT350N_V2_NOR_BOOT_BASE,
WRT350N_V2_NOR_BOOT_SIZE);
platform_device_register(&wrt350n_v2_nor_flash);
platform_device_register(&wrt350n_v2_leds);
platform_device_register(&wrt350n_v2_button_device);
}
static void __init dt2_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(dt2_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_uart0_init();
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_i2c_init();
orion5x_sata_init(&dt2_sata_data);
orion5x_xor_init();
printk(KERN_INFO "U-Boot parameters:\n");
printk(KERN_INFO "Sys Clk = %d, Tclk = %d, BoardID = 0x%02x\n", mvSysclk, mvTclk, gBoardId);
printk(KERN_INFO "Serial: %s\n", dt2_eeprom.fc.dt2_serial_number);
printk(KERN_INFO "Revision: %016x\n", dt2_eeprom.fc.dt2_revision);
printk(KERN_INFO "DT2: Using MAC address %pM for port 0\n",
dt2_eeprom.gw.mac_addr[0]);
printk(KERN_INFO "DT2: Using MAC address %pM for port 1\n",
dt2_eeprom.gw.mac_addr[1]);
orion5x_eth_init(&dt2_eth_data);
memcpy(dt2_eth_data.mac_addr, dt2_eeprom.gw.mac_addr[0], 6);
orion5x_eth_switch_init(&dt2_switch_plat_data, NO_IRQ);
i2c_register_board_info(0, &dt2_i2c_rtc, 1);
mvebu_mbus_add_window("devbus-boot", DT2_NOR_BOOT_BASE,
DT2_NOR_BOOT_SIZE);
platform_device_register(&dt2_nor_flash);
mvebu_mbus_add_window("devbus-cs0", DT2_LEDS_BASE, DT2_LEDS_SIZE);
platform_device_register(&dt2_leds);
if (request_irq(gpio_to_irq(DT2_PIN_GPIO_RESET), &dt2_reset_handler,
IRQF_DISABLED | IRQF_TRIGGER_LOW,
"DT2: Reset button", NULL) < 0) {
printk("DT2: Reset Button IRQ %d not available\n",
gpio_to_irq(DT2_PIN_GPIO_RESET));
}
if (request_irq(gpio_to_irq(DT2_PIN_GPIO_POWER), &dt2_power_handler,
IRQF_DISABLED | IRQF_TRIGGER_LOW,
"DT2: Power button", NULL) < 0) {
printk(KERN_DEBUG "DT2: Power Button IRQ %d not available\n",
gpio_to_irq(DT2_PIN_GPIO_POWER));
}
}
static void __init rd88f5181l_ge_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(rd88f5181l_ge_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data);
orion5x_i2c_init();
orion5x_uart0_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
RD88F5181L_GE_NOR_BOOT_BASE,
RD88F5181L_GE_NOR_BOOT_SIZE);
platform_device_register(&rd88f5181l_ge_nor_boot_flash);
i2c_register_board_info(0, &rd88f5181l_ge_i2c_rtc, 1);
}
static void __init db88f5281_init(void)
{
orion5x_init();
orion5x_mpp_conf(db88f5281_mpp_modes);
writel(0, MPP_DEV_CTRL);
orion5x_ehci0_init();
orion5x_eth_init(&db88f5281_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_setup_dev_boot_win(DB88F5281_NOR_BOOT_BASE,
DB88F5281_NOR_BOOT_SIZE);
platform_device_register(&db88f5281_boot_flash);
orion5x_setup_dev0_win(DB88F5281_7SEG_BASE, DB88F5281_7SEG_SIZE);
orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE);
platform_device_register(&db88f5281_nor_flash);
orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE);
platform_device_register(&db88f5281_nand_flash);
i2c_register_board_info(0, &db88f5281_i2c_rtc, 1);
}
static void __init rd88f5181l_ge_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(rd88f5181l_ge_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data,
gpio_to_irq(8));
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_setup_dev_boot_win(RD88F5181L_GE_NOR_BOOT_BASE,
RD88F5181L_GE_NOR_BOOT_SIZE);
platform_device_register(&rd88f5181l_ge_nor_boot_flash);
i2c_register_board_info(0, &rd88f5181l_ge_i2c_rtc, 1);
}
static void __init d2net_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(d2net_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&d2net_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
d2net_sata_power_init();
orion5x_sata_init(&d2net_sata_data);
orion5x_setup_dev_boot_win(D2NET_NOR_BOOT_BASE,
D2NET_NOR_BOOT_SIZE);
platform_device_register(&d2net_nor_flash);
platform_device_register(&d2net_gpio_buttons);
d2net_gpio_leds_init();
pr_notice("d2net: Flash write are not yet supported.\n");
i2c_register_board_info(0, d2net_i2c_devices,
ARRAY_SIZE(d2net_i2c_devices));
orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
}
static void __init db88f5281_init(void)
{
/*
* Basic Orion setup. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(db88f5281_mpp_modes);
writel(0, MPP_DEV_CTRL); /* DEV_D[31:16] */
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&db88f5281_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_setup_dev_boot_win(DB88F5281_NOR_BOOT_BASE,
DB88F5281_NOR_BOOT_SIZE);
platform_device_register(&db88f5281_boot_flash);
orion5x_setup_dev0_win(DB88F5281_7SEG_BASE, DB88F5281_7SEG_SIZE);
orion5x_setup_dev1_win(DB88F5281_NOR_BASE, DB88F5281_NOR_SIZE);
platform_device_register(&db88f5281_nor_flash);
orion5x_setup_dev2_win(DB88F5281_NAND_BASE, DB88F5281_NAND_SIZE);
platform_device_register(&db88f5281_nand_flash);
i2c_register_board_info(0, &db88f5281_i2c_rtc, 1);
}
static void __init dns323_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
orion5x_mpp_conf(dns323_mpp_modes);
writel(0, MPP_DEV_CTRL); /* DEV_D[31:16] */
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&dns323_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
/* setup flash mapping
* CS3 holds a 8 MB Spansion S29GL064M90TFIR4
*/
orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE);
platform_device_register(&dns323_nor_flash);
platform_device_register(&dns323_gpio_leds);
platform_device_register(&dns323_button_device);
i2c_register_board_info(0, dns323_i2c_devices,
ARRAY_SIZE(dns323_i2c_devices));
/* register dns323 specific power-off method */
if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
pr_err("DNS323: failed to setup power-off GPIO\n");
pm_power_off = dns323_power_off;
}
static void __init qnap_ts209_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(ts209_mpp_modes);
/*
* MPP[20] PCI clock 0
* MPP[21] PCI clock 1
* MPP[22] USB 0 over current
* MPP[23-25] Reserved
*/
/*
* Configure peripherals.
*/
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
QNAP_TS209_NOR_BOOT_BASE,
QNAP_TS209_NOR_BOOT_SIZE);
platform_device_register(&qnap_ts209_nor_flash);
orion5x_ehci0_init();
orion5x_ehci1_init();
qnap_tsx09_find_mac_addr(QNAP_TS209_NOR_BOOT_BASE +
qnap_ts209_partitions[5].offset,
qnap_ts209_partitions[5].size);
orion5x_eth_init(&qnap_tsx09_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&qnap_ts209_sata_data);
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_xor_init();
platform_device_register(&qnap_ts209_button_device);
/* Get RTC IRQ and register the chip */
if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) {
if (gpio_direction_input(TS209_RTC_GPIO) == 0)
qnap_ts209_i2c_rtc.irq = gpio_to_irq(TS209_RTC_GPIO);
else
gpio_free(TS209_RTC_GPIO);
}
if (qnap_ts209_i2c_rtc.irq == 0)
pr_warning("qnap_ts209_init: failed to get RTC IRQ\n");
i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1);
/* register tsx09 specific power-off method */
pm_power_off = qnap_tsx09_power_off;
}
static void __init rd88f5181l_fxo_init(void)
{
orion5x_init();
orion5x_mpp_conf(rd88f5181l_fxo_mpp_modes);
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
orion5x_eth_switch_init(&rd88f5181l_fxo_switch_plat_data, NO_IRQ);
orion5x_uart0_init();
orion5x_setup_dev_boot_win(RD88F5181L_FXO_NOR_BOOT_BASE,
RD88F5181L_FXO_NOR_BOOT_SIZE);
platform_device_register(&rd88f5181l_fxo_nor_boot_flash);
}
static void __init rd88f6183ap_ge_init(void)
{
orion5x_init();
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data,
gpio_to_irq(3));
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
orion5x_uart0_init();
}
static void __init wrt350n_v2_init(void)
{
orion5x_init();
orion5x_mpp_conf(wrt350n_v2_mpp_modes);
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
orion5x_eth_switch_init(&wrt350n_v2_switch_plat_data, NO_IRQ);
orion5x_uart0_init();
orion5x_setup_dev_boot_win(WRT350N_V2_NOR_BOOT_BASE,
WRT350N_V2_NOR_BOOT_SIZE);
platform_device_register(&wrt350n_v2_nor_flash);
}
static void __init mss2_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
orion5x_mpp_conf(mss2_mpp_modes);
/*
* MPP[20] Unused
* MPP[21] PCI clock
* MPP[22] USB 0 over current
* MPP[23] USB 1 over current
*/
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&mss2_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&mss2_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
MSS2_NOR_BOOT_BASE,
MSS2_NOR_BOOT_SIZE);
platform_device_register(&mss2_nor_flash);
platform_device_register(&mss2_button_device);
if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
else
gpio_free(MSS2_GPIO_RTC_IRQ);
}
i2c_register_board_info(0, &mss2_i2c_rtc, 1);
/* register mss2 specific power-off method */
pm_power_off = mss2_power_off;
}
static void __init rd88f5181l_ge_init(void)
{
orion5x_init();
orion5x_mpp_conf(rd88f5181l_ge_mpp_modes);
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_ge_eth_data);
orion5x_eth_switch_init(&rd88f5181l_ge_switch_plat_data,
gpio_to_irq(8));
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_setup_dev_boot_win(RD88F5181L_GE_NOR_BOOT_BASE,
RD88F5181L_GE_NOR_BOOT_SIZE);
platform_device_register(&rd88f5181l_ge_nor_boot_flash);
i2c_register_board_info(0, &rd88f5181l_ge_i2c_rtc, 1);
}
static void __init rd88f6183ap_ge_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f6183ap_ge_eth_data);
orion5x_eth_switch_init(&rd88f6183ap_ge_switch_plat_data,
gpio_to_irq(3));
spi_register_board_info(rd88f6183ap_ge_spi_slave_info,
ARRAY_SIZE(rd88f6183ap_ge_spi_slave_info));
orion5x_spi_init();
orion5x_uart0_init();
}
static void __init qnap_ts409_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(ts409_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_setup_dev_boot_win(QNAP_TS409_NOR_BOOT_BASE,
QNAP_TS409_NOR_BOOT_SIZE);
platform_device_register(&qnap_ts409_nor_flash);
orion5x_ehci0_init();
qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE +
qnap_ts409_partitions[5].offset,
qnap_ts409_partitions[5].size);
orion5x_eth_init(&qnap_tsx09_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_uart1_init();
platform_device_register(&qnap_ts409_button_device);
/* Get RTC IRQ and register the chip */
if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) {
if (gpio_direction_input(TS409_RTC_GPIO) == 0)
qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO);
else
gpio_free(TS409_RTC_GPIO);
}
if (qnap_ts409_i2c_rtc.irq == 0)
pr_warning("qnap_ts409_init: failed to get RTC IRQ\n");
i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1);
platform_device_register(&ts409_leds);
/* register tsx09 specific power-off method */
pm_power_off = qnap_tsx09_power_off;
}
static void __init net2big_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(net2big_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&net2big_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_xor_init();
net2big_sata_power_init();
orion5x_sata_init(&net2big_sata_data);
orion5x_setup_dev_boot_win(NET2BIG_NOR_BOOT_BASE,
NET2BIG_NOR_BOOT_SIZE);
platform_device_register(&net2big_nor_flash);
platform_device_register(&net2big_gpio_buttons);
net2big_gpio_leds_init();
i2c_register_board_info(0, net2big_i2c_devices,
ARRAY_SIZE(net2big_i2c_devices));
orion_gpio_set_valid(NET2BIG_GPIO_POWER_OFF, 1);
if (gpio_request(NET2BIG_GPIO_POWER_OFF, "power-off") == 0 &&
gpio_direction_output(NET2BIG_GPIO_POWER_OFF, 0) == 0)
pm_power_off = net2big_power_off;
else
pr_err("net2big: failed to configure power-off GPIO\n");
pr_notice("net2big: Flash writing is not yet supported.\n");
}
static void __init rd88f5182_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(rd88f5182_mpp_modes);
/*
* MPP[20] PCI Clock to MV88F5182
* MPP[21] PCI Clock to mini PCI CON11
* MPP[22] USB 0 over current indication
* MPP[23] USB 1 over current indication
* MPP[24] USB 1 over current enable
* MPP[25] USB 0 over current enable
*/
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&rd88f5182_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&rd88f5182_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
RD88F5182_NOR_BOOT_BASE,
RD88F5182_NOR_BOOT_SIZE);
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_TARGET(1),
ORION_MBUS_DEVBUS_ATTR(1),
RD88F5182_NOR_BASE,
RD88F5182_NOR_SIZE);
platform_device_register(&rd88f5182_nor_flash);
platform_device_register(&rd88f5182_gpio_leds);
i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1);
}
static void __init wrt350n_v2_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(wrt350n_v2_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&wrt350n_v2_eth_data);
orion5x_uart0_init();
orion5x_setup_dev_boot_win(WRT350N_V2_NOR_BOOT_BASE,
WRT350N_V2_NOR_BOOT_SIZE);
platform_device_register(&wrt350n_v2_nor_flash);
}
static void __init rd88f5181l_fxo_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(rd88f5181l_fxo_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&rd88f5181l_fxo_eth_data);
orion5x_uart0_init();
orion5x_setup_dev_boot_win(RD88F5181L_FXO_NOR_BOOT_BASE,
RD88F5181L_FXO_NOR_BOOT_SIZE);
platform_device_register(&rd88f5181l_fxo_nor_boot_flash);
}
static void __init lsmini_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(lsmini_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&lsmini_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&lsmini_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
ORION_MBUS_DEVBUS_BOOT_ATTR,
LSMINI_NOR_BOOT_BASE,
LSMINI_NOR_BOOT_SIZE);
platform_device_register(&lsmini_nor_flash);
platform_device_register(&lsmini_button_device);
platform_device_register(&lsmini_leds);
i2c_register_board_info(0, &lsmini_i2c_rtc, 1);
/* enable USB power */
gpio_set_value(LSMINI_GPIO_USB_POWER, 1);
/* register power-off method */
pm_power_off = lsmini_power_off;
pr_info("%s: finished\n", __func__);
}
static void __init lschl_init(void)
{
/*
* Setup basic Orion functions. Needs to be called early.
*/
orion5x_init();
orion5x_mpp_conf(lschl_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&lschl_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&lschl_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(LSCHL_NOR_BOOT_BASE,
LSCHL_NOR_BOOT_SIZE);
platform_device_register(&lschl_nor_flash);
platform_device_register(&lschl_leds);
platform_device_register(&lschl_button_device);
platform_device_register(&lschl_fan_device);
i2c_register_board_info(0, &lschl_i2c_rtc, 1);
/* usb power on */
gpio_set_value(LSCHL_GPIO_USB_POWER, 1);
/* register power-off method */
pm_power_off = lschl_power_off;
pr_info("%s: finished\n", __func__);
}
static void __init edmini_v2_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(edminiv2_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_eth_init(&edmini_v2_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&edmini_v2_sata_data);
orion5x_uart0_init();
orion5x_setup_dev_boot_win(EDMINI_V2_NOR_BOOT_BASE,
EDMINI_V2_NOR_BOOT_SIZE);
platform_device_register(&edmini_v2_nor_flash);
platform_device_register(&edmini_v2_gpio_leds);
platform_device_register(&edmini_v2_gpio_buttons);
pr_notice("edmini_v2: USB device port, flash write and power-off "
"are not yet supported.\n");
/* Get RTC IRQ and register the chip */
if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
else
gpio_free(EDMINIV2_RTC_GPIO);
}
if (edmini_v2_i2c_rtc.irq == 0)
pr_warning("edmini_v2: failed to get RTC IRQ\n");
i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
}
static void __init mv2120_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
orion5x_mpp_conf(mv2120_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&mv2120_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&mv2120_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(MV2120_NOR_BOOT_BASE, MV2120_NOR_BOOT_SIZE);
platform_device_register(&mv2120_nor_flash);
platform_device_register(&mv2120_button_device);
if (gpio_request(MV2120_GPIO_RTC_IRQ, "rtc") == 0) {
if (gpio_direction_input(MV2120_GPIO_RTC_IRQ) == 0)
mv2120_i2c_rtc.irq = gpio_to_irq(MV2120_GPIO_RTC_IRQ);
else
gpio_free(MV2120_GPIO_RTC_IRQ);
}
i2c_register_board_info(0, &mv2120_i2c_rtc, 1);
platform_device_register(&mv2120_leds);
/* register mv2120 specific power-off method */
if (gpio_request(MV2120_GPIO_POWER_OFF, "POWEROFF") != 0 ||
gpio_direction_output(MV2120_GPIO_POWER_OFF, 1) != 0)
pr_err("mv2120: failed to setup power-off GPIO\n");
pm_power_off = mv2120_power_off;
}
static void __init rd88f5182_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(rd88f5182_mpp_modes);
/*
* MPP[20] PCI Clock to MV88F5182
* MPP[21] PCI Clock to mini PCI CON11
* MPP[22] USB 0 over current indication
* MPP[23] USB 1 over current indication
* MPP[24] USB 1 over current enable
* MPP[25] USB 0 over current enable
*/
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&rd88f5182_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&rd88f5182_sata_data);
orion5x_uart0_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(RD88F5182_NOR_BOOT_BASE,
RD88F5182_NOR_BOOT_SIZE);
orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE);
platform_device_register(&rd88f5182_nor_flash);
i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1);
}
static void __init tsp2_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(tsp2_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_setup_dev_boot_win(TSP2_NOR_BOOT_BASE,
TSP2_NOR_BOOT_SIZE);
platform_device_register(&tsp2_nor_flash);
orion5x_ehci0_init();
orion5x_eth_init(&tsp2_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
orion5x_uart1_init();
/* Get RTC IRQ and register the chip */
if (gpio_request(TSP2_RTC_GPIO, "rtc") == 0) {
if (gpio_direction_input(TSP2_RTC_GPIO) == 0)
tsp2_i2c_rtc.irq = gpio_to_irq(TSP2_RTC_GPIO);
else
gpio_free(TSP2_RTC_GPIO);
}
if (tsp2_i2c_rtc.irq == 0)
pr_warning("tsp2_init: failed to get RTC IRQ\n");
i2c_register_board_info(0, &tsp2_i2c_rtc, 1);
/* register Terastation Pro II specific power-off method */
pm_power_off = tsp2_power_off;
}
static void __init kurobox_pro_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(kurobox_pro_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&kurobox_pro_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&kurobox_pro_sata_data);
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
KUROBOX_PRO_NOR_BOOT_SIZE);
platform_device_register(&kurobox_pro_nor_flash);
if (machine_is_kurobox_pro()) {
orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
KUROBOX_PRO_NAND_SIZE);
platform_device_register(&kurobox_pro_nand_flash);
}
i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
/* register Kurobox Pro specific power-off method */
pm_power_off = kurobox_pro_power_off;
}
static void __init dns323_init(void)
{
/* Setup basic Orion functions. Need to be called early. */
orion5x_init();
/* Identify revision */
system_rev = dns323_identify_rev();
pr_info("DNS-323: Identified HW revision %c1\n", 'A' + system_rev);
/* Just to be tricky, the 5182 has a completely different
* set of MPP modes to the 5181.
*/
switch(system_rev) {
case DNS323_REV_A1:
orion5x_mpp_conf(dns323a_mpp_modes);
writel(0, MPP_DEV_CTRL); /* DEV_D[31:16] */
break;
case DNS323_REV_B1:
orion5x_mpp_conf(dns323b_mpp_modes);
break;
case DNS323_REV_C1:
orion5x_mpp_conf(dns323c_mpp_modes);
break;
}
/* setup flash mapping
* CS3 holds a 8 MB Spansion S29GL064M90TFIR4
*/
orion5x_setup_dev_boot_win(DNS323_NOR_BOOT_BASE, DNS323_NOR_BOOT_SIZE);
platform_device_register(&dns323_nor_flash);
/* Sort out LEDs, Buttons and i2c devices */
switch(system_rev) {
case DNS323_REV_A1:
/* The 5181 power LED is active low and requires
* DNS323_GPIO_LED_POWER1 to also be low.
*/
dns323ab_leds[0].active_low = 1;
gpio_request(DNS323_GPIO_LED_POWER1, "Power Led Enable");
gpio_direction_output(DNS323_GPIO_LED_POWER1, 0);
/* Fall through */
case DNS323_REV_B1:
i2c_register_board_info(0, dns323ab_i2c_devices,
ARRAY_SIZE(dns323ab_i2c_devices));
break;
case DNS323_REV_C1:
/* Hookup LEDs & Buttons */
dns323_gpio_leds.dev.platform_data = &dns323c_led_data;
dns323_button_device.dev.platform_data = &dns323c_button_data;
/* Hookup i2c devices and fan driver */
i2c_register_board_info(0, dns323c_i2c_devices,
ARRAY_SIZE(dns323c_i2c_devices));
platform_device_register_simple("dns323c-fan", 0, NULL, 0);
/* Register fixup for the PHY LEDs */
phy_register_fixup_for_uid(MARVELL_PHY_ID_88E1118,
MARVELL_PHY_ID_MASK,
dns323c_phy_fixup);
}
platform_device_register(&dns323_gpio_leds);
platform_device_register(&dns323_button_device);
/*
* Configure peripherals.
*/
if (dns323_read_mac_addr() < 0)
printk("DNS-323: Failed to read MAC address\n");
orion5x_ehci0_init();
orion5x_eth_init(&dns323_eth_data);
orion5x_i2c_init();
orion5x_uart0_init();
/* Remaining GPIOs */
switch(system_rev) {
case DNS323_REV_A1:
/* Poweroff GPIO */
if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
pr_err("DNS-323: failed to setup power-off GPIO\n");
pm_power_off = dns323a_power_off;
break;
case DNS323_REV_B1:
/* 5182 built-in SATA init */
orion5x_sata_init(&dns323_sata_data);
/* The DNS323 rev B1 has flag to indicate the system is up.
* Without this flag set, power LED will flash and cannot be
* controlled via leds-gpio.
*/
if (gpio_request(DNS323_GPIO_SYSTEM_UP, "SYS_READY") == 0)
gpio_direction_output(DNS323_GPIO_SYSTEM_UP, 1);
/* Poweroff GPIO */
if (gpio_request(DNS323_GPIO_POWER_OFF, "POWEROFF") != 0 ||
gpio_direction_output(DNS323_GPIO_POWER_OFF, 0) != 0)
pr_err("DNS-323: failed to setup power-off GPIO\n");
pm_power_off = dns323b_power_off;
break;
case DNS323_REV_C1:
/* 5182 built-in SATA init */
orion5x_sata_init(&dns323_sata_data);
/* Poweroff GPIO */
if (gpio_request(DNS323C_GPIO_POWER_OFF, "POWEROFF") != 0 ||
gpio_direction_output(DNS323C_GPIO_POWER_OFF, 0) != 0)
pr_err("DNS-323: failed to setup power-off GPIO\n");
pm_power_off = dns323c_power_off;
/* Now, -this- should theorically be done by the sata_mv driver
* once I figure out what's going on there. Maybe the behaviour
* of the LEDs should be somewhat passed via the platform_data.
* for now, just whack the register and make the LEDs happy
*
* Note: AFAIK, rev B1 needs the same treatement but I'll let
* somebody else test it.
*/
writel(0x5, ORION5X_SATA_VIRT_BASE | 0x2c);
break;
}
}